วีดีโอ

Is bad check you thermal paste, fan, and airflow.

At full load not ideal, too high. If thats the temperature at idle, then something is very wrong.

@@hayemiranda7647 at full load and the fan is hella loud like 3200 rpm and 85 degrees but I have this like msi version or something and it's known to be loud and hot 🔥🥵 so I think I'm good cuz a lot of people used it like that for couple of years

Wrong, terrible advice. Many cases of crashing on TH-cam by using 1mm on Saphire RX 500 cards (their stock pads are 0.75mm from fabric). Do not use 1mm on these cards it will not squish enough for the heatsink to make proper contact with the processor. 0.5mm does the job here.

Yes. Ive seen many cases of crashing by using 1.0mm on Saphire RX 500 séries. Use 0.5mm thermal pads If needed.

I put it directly on the pci 16x slot.

I used only 0.5mm.

That's what I did, until the VRAM chips overheated and produced artifacts. Can't even run 4K benchmarks in superposition without it crashing the program. I now use thermal putty instead, which lowered temps more than previously. The only caveat is that it's a mess to clean.

@@ryzeeboi7637 im use 0.5mm for vram but did not have contact to heat sink. officially shapphire use 0.75mm but they say its safe to use 0.5mm

what was the GPU you used the 0.5mm pads on?

They are in the description.

100-110 like every gpz. For everyday use dont get over 85

@@L4ftyOne ok thanks

I recommend 70°C

same situation, what problems did u have? mine is crashing in furmark reaching 86celsius and also crashing while exporting in premiere with fans spinning at max and losing signal

mine just wouldn't boot man no clue what the problem might be for you @@adrian3126

1920x1080

Try 0.5mm, 1.0 thermal pads are too thick according to online sources

@@tanja-k thx

@@tanja-k could I get away with only using thermal paste instead of pads in a pinch?

You can, but I don’t recommend it, because it will make a mess and will be not that effective probably.

I used 0.5 mm pads.

The case is Cougar MG130-G with only one exhaust fan and room temperature was probably 18 degrees celsius.

​​@@ryzeeboi7637eans if i get 2 intake fans with stock cooler, will temperature be less than no intake fan? also here in summers the temperature is about 30°c.

Before was 85 degrees and after was 70.

​@@ryzeeboi7637same,I will do it

I don’t have an 6500XT

Yes, if you use a bit lower settings than the highest.

I don’t know, maybe they optimized it.

Thank you,i used isopropyl alcohol,but the paste was really old,dry and stuck.

@@ryzeeboi7637 use Zippo fuel to soften the old thermal paste. put a kitchenpaper on the Die and keep it wet for 10 minutes. then use cotton tips to clean.

i use WD40 contact cleaner is good as well

Obrigada!

Yes,0.5mm.

when i remove the heatsink cover that metal bar part comes over it how can i put it back on pcb board? i temporary put thermal paste on it to prevent over heating issues thou

@@ryzeeboi7637 also for the 8gb version?

Nah, 0.5mm won't make contact at all for this model. The person from the video made a huge mistake. 1.0mm is a way to go.

​​@@zeljkorilke701i have problem with 1 mm, i will try 0.5 mm

Sorry,i sold the GPU.

You are welcome!

@@ryzeeboi7637 Thank you aswell. A lot of used cards enter secound hand market and this was perfect for fixing thermals. By the way did it improve efficiency for you?

No,the efficiency didn’t change.

Yes

DVI-D port,two HDMI ports and two DisplayPorts

Output only. You would need a dedicated capture card if you want to capture any footage that isn't generated by the GPU.

I don’t own the GPU anymore,sorry.

Estoy feliz por haber ayudado!

Dejan mucho que desear los cooler stock de intel

It supports LGA1200,go to the official arctic website for the freezer 34 esports duo and check the technical specifications.

Don't know how or where you read that-it clearly says it does....SMH

Lga 1151 supported coolers also support lga 1200

If you ask me there isn’t a bottleneck here.