Not too bad, it looks a lot better. However, I'd get the Dremel out using a burr and completely refinish the frame with the engraving on, so its all uniform. A Dremel with wire brush wheel might be able to clean the knurling up a bit more too. Also, I think there might be an end ratchet missing off the back of the thimble. I might buy a basket case and have a go...I got inspired.
@@LordPrecision you can't inspect it by looks. I have had over 3 micron errors in perfectly good looking Japanese micrometer screws. In my best ones I can't tell the error is there. The reading in this is 1 thou but the accuracy is still 1 tenth
Sir I removed the spindle to lubricte it and after it was done I tried to scre the spindle back but it had become tight to screw it? Anybody pls suggest the solution
I assume it's not cross threaded? This one came apart and was re-assembled ok. I use it now and again and it's not as free as my other micrometers maybe that's because it has been serviced and needs time to wear in. Sorry not sure what to say after that..good luck hope you get it sorted.
![THE TOYS x NONT TANONT - ดอกไม้ที่รอฝน (spring) [Official MV]](http://i.ytimg.com/vi/pPa1d5cC8M4/mqdefault.jpg)
![คุณอาเรียโต๊ะข้างๆ พูดรัสเซียหวานใส่ซะหัวใจจะวาย ตอนที่ 4 [ซับไทย] 【Ani-One Thailand】](http://i.ytimg.com/vi/_vK_cden2f8/mqdefault.jpg)
Various grits of black oxide paper might work better then Scotchbrite 🤔
Спасибо все очень подробно. Отдельное спасибо за лунную сонату
Nice job, thanks a lot for sharing!
Super👌👌👌
Sir micro meter ka pura part lag karka dikhaiye🎉
Not too bad, it looks a lot better. However, I'd get the Dremel out using a burr and completely refinish the frame with the engraving on, so its all uniform. A Dremel with wire brush wheel might be able to clean the knurling up a bit more too. Also, I think there might be an end ratchet missing off the back of the thimble. I might buy a basket case and have a go...I got inspired.
Thanks for the comment and advice.
This model has a friction thimble and therefore does not have the end ratchet.
@@andrewdolinskiatcarpathian Yes you're correct, Thanks for the clarification about this.
supper
மிக பயனுள்ள காணொளி
Need Mauser micrometre service video
your vid would be way better if you got rid of all the music and talked to your audience.
I would not trust it without a thorough test with various gage blocks.
@@LordPrecision you can't inspect it by looks. I have had over 3 micron errors in perfectly good looking Japanese micrometer screws. In my best ones I can't tell the error is there. The reading in this is 1 thou but the accuracy is still 1 tenth
Sir I removed the spindle to lubricte it and after it was done I tried to scre the spindle back but it had become tight to screw it?
Anybody pls suggest the solution
I assume it's not cross threaded? This one came apart and was re-assembled ok. I use it now and again and it's not as free as my other micrometers maybe that's because it has been serviced and needs time to wear in. Sorry not sure what to say after that..good luck hope you get it sorted.
@@darrensworkshop6783 great it's gave me a way to fixed my problem
The audacity, tsk, tsk, tsk. Mr. phat fingers forgets to assemble the washer under the locking lever. 🤪🤣😂
Need Mauser micrometre service video
look at my channel for Mauser mics and service.