I have a graco 490, when i turn it on and it does nothing just the light D20 turns on and after a while it turns off. Is there any way you can tell me whats wrong with it?
Taking my old Graco Ultimate MX 695 pressure control apart when the cover plate came off two wires came off. The wires are black and white. The three receptacles are labeled, L1, L2, and Looks like J11. Can anyone tell me where the black and white wires go? I have a photo but can't post it here. Thanks
I have 795 graco.. I got E03 on screen.. I change the transducer.the fault E03 is disapear. But My problem now is the machine continue pressuering whitout stop.also i change the drain valve ..still not fixed. Can you advice pls?
Idk man. I have a gas powered 5900 and the only thing that goes bad periodically is the packing. I spray the sewers with a paint/pesticide mix. The rig is bolted to the back of the truck. This includes being on steep inclines and a lot of rough off-road stuff. The rig generally runs 8~36 hours straight. In 4 years and 43k gallons of material I've only replaced the packing twice, piston rod once and now the transducer(snapped bouncing around off-road). This is all while sitting in the hot AZ sun.
This is the least helpful tutorial I've ever seen. Think the transducer is busted? Step one, buy a transducer 🤣😭 Side note: I actually have an extra transducer to test it with. But I think your average painter would not have a machine graveyard
So the way to troubleshoot the part.....IS TO BUY A NEW PART? brilliant! Thank you for your expertise!
That’s the way to make business
I have a graco 490, when i turn it on and it does nothing just the light D20 turns on and after a while it turns off. Is there any way you can tell me whats wrong with it?
I have the same problem I’m pretty sure it’s the transducer
I have a 795 ultra max electronic Airless sprayer I replaced the power cord it started up and shut off like it's getting no power
Taking my old Graco Ultimate MX 695 pressure control apart when the cover plate came off two wires came off. The wires are black and white. The three receptacles are labeled, L1, L2, and Looks like J11. Can anyone tell me where the black and white wires go? I have a photo but can't post it here. Thanks
Hey do you still need help?
I have a graco mx2 1095 I have problems it does not give codes only 4 led points on the screen can someone help me solve it please thank you😊
I got a graco 795 and the screen says code 02 high pressure can u help me on that please sir
You ever figure it out I'm having the same issue
I have 795 graco.. I got E03 on screen.. I change the transducer.the fault E03 is disapear. But My problem now is the machine continue pressuering whitout stop.also i change the drain valve ..still not fixed. Can you advice pls?
I having this same problem, did find the solution?! Please help
@@oswaldonunez999 yes ..i change the mother board ..then its work well
@@fencer1965 thank you 👍🏼
@@oswaldonunez999 welcome
transducer where you can accessibly get to it.
It is screwed inside the filter casing then the other end, looking like a telephone jack, is plugged into the board.
They make these so they can break down, hence you spend more money on them. Marketing is important for their business.
Idk man. I have a gas powered 5900 and the only thing that goes bad periodically is the packing. I spray the sewers with a paint/pesticide mix. The rig is bolted to the back of the truck. This includes being on steep inclines and a lot of rough off-road stuff. The rig generally runs 8~36 hours straight. In 4 years and 43k gallons of material I've only replaced the packing twice, piston rod once and now the transducer(snapped bouncing around off-road). This is all while sitting in the hot AZ sun.
This is the least helpful tutorial I've ever seen. Think the transducer is busted? Step one, buy a transducer 🤣😭
Side note: I actually have an extra transducer to test it with. But I think your average painter would not have a machine graveyard