+Josh Eichelberger Actually most cases are due to line loosen. The worst case is control board no working, but replacing is not complicated either. You can see my other video- how to take part the scooter.
Hi I just got the board the other day and when I try to ride it wheels do not move the circle light on the left side don't come on when I stand on it also just the green battery on the right come on I have the same one any help ??????
+Gunnar Hansen Actualy, I have send it to my friend who is doing repairs of industrial electronic equipment, and he found that one chip on the main board is broken. As he said, there are three same circuits and on that one protective diode is mounted wrong (polarity is not good). Now we need that kind of circuit, but there is not any data...
If you have a red flashing light on one side and it wont move and Recalibrate doesn't fix it... Check all plugs and wires are getting good connection (Especially the 5 wire sockets). If they are and it still don't move then it probly has a blown output fet on the side thats red. They're easy to change.. MAKE SURE BATTERY IS UNPLUGGED!! Measure the Mosfets, 6 on a heatsink per side(GDS)... Usually only 1 or 2 short... DMM to Diode, Neg on Center pin (Drain), Gate approx +1.5v, Source approx .5v. YST7575C crosses to RU6888R 68v 88a TO220 *** For the 12 Fet Mainboard Model, one bank of Fets controls one drive wheel. Do a continuity test to figure out what bank controls what side.. Each bank of Fets, are broken into pairs per thick drive wheel wire (YGB)..
I have the same problem but my hoverboard is the one with Bluetooth and lights on the top of the wheels and one of the wheels feels weird it's feels like bumps when I turn the wheel can you tell me what's the problem
+Cris Ramos Have you try to reset the hoverboard? can find video about that on youtube, but a very important point is the final step, you cannot turn off the hoverboard until the red light keep flashing for at least 8 times. Someone turn off only flashing 3 or 4 times, that may cause loss of program, then hoverboard is broken.
well I did try this solution, has worked for me before but now the problem continues with the gyro red light blinking twice.. what could possibly be wrong.?
mine wouldn't turn on so i replaced every single part and now it works perfect. the only problem is that the battery light does not turn on and it won't charge it at all. i have tried different chargers and it just won't charge it. can you please help?? thank you
I have pretty much the same problem as you, but my lights blink 2 times at once (not 4 times as yours). I have tried to connect all the wires, but it still doesn't work!
+Le Sussie Yes I have double checked all the pins, but nothing works. I am pretty sure it something else since even the blinking cycle is different than yours!
Le Sussie I've tried calibrating it and all I can't figure it out it had the red light but now it shut off and won't work the 2 wheels do not move or anything
same thing to me is happening, changed the gyroscope, reconnected everything, pushed every pin, still nothing and still blinking 5 times when I put pressure on the pads ...
thank you so much, I was going to throw it away but it now works again and you've made someone very happy
thank you so much i thought i was gonna have to start walking again and then i came across this video and now my hoverboards working
I had the same problem I just did as in your video and my problem was solved thank you very much
going to try that tomorrow. hopefully it works great video!
+Josh Eichelberger Actually most cases are due to line loosen. The worst case is control board no working, but replacing is not complicated either. You can see my other video- how to take part the scooter.
extremely helpful Fixed the problem Thank you so much!
I have this problem with my lohawk , do I need to do the same thing you did with the pen and spread the plug ?
Thank you so much it worked perfectly I did every step and it work thank you thank you !!
Thank you so much ❤❤❤
Thank you for the video.
Omg YESS it works thank you so much
the indicator light is green, but the wheels do not spin, it's like this in the video but without the red indicator, what it is can be?
Hi I just got the board the other day and when I try to ride it wheels do not move the circle light on the left side don't come on when I stand on it also just the green battery on the right come on I have the same one any help ??????
+Isiaah Scott Firstly, full charging . If no working, it should be line loosen. Remove the back cover, check all pins, disconnect them and reconnect .
My two lights are on but one side is weaker or sometimes won't move what do I do is it a gryoscope or something else
I'm about to go try this right now
Hi Le, i also have a problem, but my red light flashes 2 times. i have check the wiring, and calibrate the device, but without success...
+Milos Tankosic Did you find a solution ? Mine is also blinking 2 times !
+Gunnar Hansen
Actualy, I have send it to my friend who is doing repairs of industrial electronic equipment, and he found that one chip on the main board is broken. As he said, there are three same circuits and on that one protective diode is mounted wrong (polarity is not good). Now we need that kind of circuit, but there is not any data...
If you have a red flashing light on one side and it wont move and Recalibrate doesn't fix it... Check all plugs and wires are getting good connection (Especially the 5 wire sockets). If they are and it still don't move then it probly has a blown output fet on the side thats red. They're easy to change.. MAKE SURE BATTERY IS UNPLUGGED!! Measure the Mosfets, 6 on a heatsink per side(GDS)... Usually only 1 or 2 short... DMM to Diode, Neg on Center pin (Drain), Gate approx +1.5v, Source approx .5v. YST7575C crosses to RU6888R 68v 88a TO220 *** For the 12 Fet Mainboard Model, one bank of Fets controls one drive wheel. Do a continuity test to figure out what bank controls what side.. Each bank of Fets, are broken into pairs per thick drive wheel wire (YGB)..
Red light keep flashing on the motherboard any solution???
Isiaah Scott that is what mine is doing . did you figure it out?
Isiaah Scott
THANK YOU SO MUCH MY WORKS NOW YAYYY😄😃👍🏼
try to calibrate your hoverboard.
Could touching the wires possibly make it blow up ?
+Aerial Green Turn off the hoverboard at first. Or disconnect the power line near the battery.
I have the same problem but my hoverboard is the one with Bluetooth and lights on the top of the wheels and one of the wheels feels weird it's feels like bumps when I turn the wheel can you tell me what's the problem
+Cris Ramos Have you try to reset the hoverboard? can find video about that on youtube, but a very important point is the final step, you cannot turn off the hoverboard until the red light keep flashing for at least 8 times. Someone turn off only flashing 3 or 4 times, that may cause loss of program, then hoverboard is broken.
well I did try this solution, has worked for me before but now the problem continues with the gyro red light blinking twice.. what could possibly be wrong.?
Same
mine wouldn't turn on so i replaced every single part and now it works perfect. the only problem is that the battery light does not turn on and it won't charge it at all. i have tried different chargers and it just won't charge it. can you please help?? thank you
+Bryan Amaro The control board needs to replace.
thanks worked
I first stopped spinning a wheel, you after the other and now works no, that I can do? already reset and nothing
Thinks it worked
when i get on my board the right side flips out and the left side is perfectly fine any solutions
What are Those that happened to me and I had to pay fifty dollars to get that repaired it’s the wheel and the motor that’s broken
Thank you!!!!
I have the same problem I did what you said and it still does not work
all these comments from 4 years ago and i just found my 4 year old one today lol also it worked
My light and battery are green. But one of the led headlights always stays on. And that side doesn't work. What do I do?😩
Me to but i really don't care
I have pretty much the same problem as you, but my lights blink 2 times at once (not 4 times as yours). I have tried to connect all the wires, but it still doesn't work!
+Le Sussie Yes I have double checked all the pins, but nothing works. I am pretty sure it something else since even the blinking cycle is different than yours!
+Enoch Banza Two times blinking may be caused by motor power line - the three green lines.
even if i charge my battery it says it charger but then i turn it on the battery light start blinking... pls help
Mine doesn't flash red but won't move it turns on fine but won't move
plz help i did exactly wht u did and it still was blinking red
calibrate it.
One side wont work how do i fix it?
HELP! My hoverboards lights stay on and it does not let me ride HELP ME PLEASE!!!
i have the same issue but this did not work. please someone help.
i think you should try to calibrate your hoverboard.
Is This Dangerous
Very ;)
This is the easiest way to get Electrocuted
I can change left and right wheels to see if they work well
+ALEJANDRO ALBERTO FUENTES URRUTIA The two wheels may be not installed very well. You may check the connection line on the motor.
I can't turn off mine, continuously beeping and flashes red light, please suggest me what should I do???
+Nishant Rajput you may try to reset it .
Le Sussie I sold it to somebody, now I am out of tension.
Le Sussie I've tried calibrating it and all I can't figure it out it had the red light but now it shut off and won't work the 2 wheels do not move or anything
Guys don't touch the battery of the Segway if u move it the Segway not move u need new battery
my bluetooth on the hoverboard stopped working how to fix
+Mark Gomes Same here, and now my keys don't work on it
Itzurgurlz Destiny&Meya bruhhhhhhhh
I have that problem but with Green lights
Help 😭 it dosnt work
My red indicator flashes 5 time help?
+TheJesterMan You can try same steps.
same thing to me is happening, changed the gyroscope, reconnected everything, pushed every pin, still nothing and still blinking 5 times when I put pressure on the pads ...
It didn't work but also one of them is not staying it keeps on going down
+Sydpyd 1234567890 Just check all the pins, disconnect them and then re-connect them.
why would you risk doing this
Blue light on but one wheels don't work
Thank uuuuuuuu it worked 👻👻👻👻👻
+Rosendo Farias No problems
le I don't know how to do it
did not work smh
doesn't work
to your hover board
nu merge
no one woukd ever do this :(
I can’t understand this even with subtitles
Alexjedeye you mad cause you ugly