RODE MOJ, ŽELIM TEBI I SVIMA BOŽJI BLAGOSLOV. TRAŽIO SAM DA VIDIM KAKO NAPRAVITI JEDNOSTAVNI, ALI DOBRU NAPRAVU ZA SAVIJANJE LIMA. EVO SADA SAM VIDIO TAKVU NAPRAVU SAGRAĐENU JEDNOSTAVNO ALI JAKO DOBRO. LIJEPO JE SVE PRIKAZANO SA PUNO UMJEŠNOSTI I LJUBAVI PREMA POSLU. TO ME RADUJE . ZAHVALAN SAM ZA IDEJU. ŽELIM PUNO USPJEHA U ŽIVOTU I RADU TEBI TVOJOJ OBITELJI I SVIMA.
Thanks for posting this. I just started making this now with a few changes. You have a 2 piece hinge, I’m using a 3 piece hinge. The center pin will be removable so I can separate the 2 angle iron pieces. The top clamp part that is held down with bolts I’ll be milling the leading edge so it’s flush with the metal that’s being bent so I can get a sharp angle at the bend, not a rounded one.
Weld a washer or metal plate on top clamp bar under where screw down is. Makes for better clampdown. Have made many benders like this in past..Plus weld some spinner handles so dont need an allen key to tighten it up
Very cool. I'd like to make one with one important difference: make the hinge not in line with the bend. I often have to clad the exteriors of windows with sheet metal and the metal is often 1.5 meters or more. The length of your bender is perfect for portability, but if I could slide longer pieces through and make the bend gradually, that would be brilliant. I currently use a little hand bender and it takes forever.
So your one can make hotdog and hamburger holders, perfect for barbeques, hotdog stands and burger vans if you make them from stainless steel. Great stuff, thankyou for sharing.
I think the piece which sits on top eith the springs is wrong. It does not provide a bemding point at all. But you could just grind it flat (45 degrees) so it sit flush. That would be a huge improvement.
Need primer on that metal, under the paint, or it will rust in no time, or simply rub off, like it was already doing with your first piece you showed being bent. Added: That bend should be able to be much sharper. Perhaps a secondary piece to put in that is shaped to be flush with the bending edge? Or just grind down that leading edge of the clamp angle, to sit flat against the base, maybe? And if you want the more curved bends available, make a secondary edge that you can slide under that clamping angle? Not sure, but many of the things I'd want to do with this would require a sharper 90° bend. Also, you should have some marks along that clamping angle, to square up the piece, and/or center it, so you end up with actual square bends.
RODE MOJ, ŽELIM TEBI I SVIMA BOŽJI BLAGOSLOV.
TRAŽIO SAM DA VIDIM KAKO NAPRAVITI JEDNOSTAVNI, ALI DOBRU NAPRAVU ZA SAVIJANJE LIMA. EVO SADA SAM VIDIO TAKVU NAPRAVU SAGRAĐENU JEDNOSTAVNO ALI JAKO DOBRO. LIJEPO JE SVE PRIKAZANO SA PUNO UMJEŠNOSTI I LJUBAVI PREMA POSLU. TO ME RADUJE . ZAHVALAN SAM ZA IDEJU. ŽELIM PUNO USPJEHA U ŽIVOTU I RADU TEBI TVOJOJ OBITELJI I SVIMA.
Thanks for posting this. I just started making this now with a few changes. You have a 2 piece hinge, I’m using a 3 piece hinge. The center pin will be removable so I can separate the 2 angle iron pieces.
The top clamp part that is held down with bolts I’ll be milling the leading edge so it’s flush with the metal that’s being bent so I can get a sharp angle at the bend, not a rounded one.
Napakagandang gayahin kaibigan. Thanks of your efforts. 👍🇵🇭
Nice work. You don't need a lot of stuff to make what you need. A center punch made out of an old threading tap👍👍.
Weld a washer or metal plate on top clamp bar under where screw down is. Makes for better clampdown. Have made many benders like this in past..Plus weld some spinner handles so dont need an allen key to tighten it up
Weld a small rod over the hex bolts to make them wing nuts ,easier than using an allen key
Very cool. Well done 👍👍
EXCELLENT JOB. THANKS FOR SHARING.
Ayos master, bagonh kaibigan...
Muy sencillo, bien explicado y sin complicaciones inecesarias...
Gracias
Gracias!!!
Muy útil y muy bien presentado
¡Buenísimo diseño! ¡gracias por compartir!
Muy bueno su invento
Congratulations! The best idea. Easy to make, functional and small to storage.
Excelente felicitaciones Maestro Venezuela gracias saludos cordiales
FERRAMENTA MUITO BOA. PARABÉNS
Super basic… Beautiful!
Nice job,mate.
Simplesmente perfeito! Parabéns!!!!!!
Very cool. I'd like to make one with one important difference: make the hinge not in line with the bend. I often have to clad the exteriors of windows with sheet metal and the metal is often 1.5 meters or more. The length of your bender is perfect for portability, but if I could slide longer pieces through and make the bend gradually, that would be brilliant. I currently use a little hand bender and it takes forever.
Well, there's still the issue of the clamp - I'm going to have to think this through some more.
Make it longer than, your hinges have to be in that spot or you'll end up with a pivot point that creates a gap and a bad bend
Good job bro 💐
Good work!
За простоту огромный плюс, а вот прижим надо делать тщательнее - угол изгиба получается не очень, радиус большой
Gracias por la explicación 👍 saludos desde cali
Muy bueno , sencillo y con poco material. 3 Angulos, uno más pequeño y dos perfiles cuadrados con dos bisagras de soldar
👍👍👍👍👍👍🙂 Excellent job. This is why I ❤ TH-cam.
Excellent job! Like and inscription..... Your friend from Brasil!!!
Good work
world need more of this
good project
can you please name for me the hinges used here?
Tom
Buen trabajo...FELICIDADES !!!!
Top mano
Very very good n best
So your one can make hotdog and hamburger holders, perfect for barbeques, hotdog stands and burger vans if you make them from stainless steel.
Great stuff, thankyou for sharing.
Your metal bend in the end, very strange in deed.
Exelente idea
Simple the best. I have to make a similar bender. Thanks for the idea.
Boa, vou fazer uma igual.
This is just brilliant. Simply the best.
Nice job
WoW! Now, this is something I can make and use in the metal shop. Great idea!
Bardzo dobra robota Pozdrowienia z Polski
Superbe vidéo
Dikit na dikit sayo.
Thank you for your video. 👍
Nicely done! Thank you for sharing.
great job, now i know what to do, to bend my metalsheet ;-)
Muy bien carnal, la voy a fabricar gracias y saludos .
Wow nic trik
So simple, yet effective, nice one 👍👍
Parabéns.....simples é eficaz
lost me when the welder came out . Most of us diy'ers do not have all the equipment we need . Nice video and product.
If you don't have a welder its unlikely you will need this tool.
@@Carsnbikes73 Ahhh but not everything bent gets welded.
Use bolt-on hinges and screws
Excelente video buen trabajo felicidades 🍾🎈🎉🎊🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍺🍻🍻🍻🍻
It was very good congratulations
Really Works Your DIY Bending Plate Ideas. Like it 👍 #creativefeature
Nice work!
U r superb bro
Great work.
Very good, thanks.
Mini bending machine is quite handy
Brilliant idea
I think the piece which sits on top eith the springs is wrong. It does not provide a bemding point at all. But you could just grind it flat (45 degrees) so it sit flush. That would be a huge improvement.
Clever!
Mantap Bang
good job my brother
Fantastic
👍👍👍👍👍👍🙂 Excellent.
That was great well done bro👍👍👍
me gusto facil de hacer y buena herramienta
Excelente, censillo y práctico 👍
Nice
Ingenioso y sencillo . Está bien la idea. saludos.
Legal hein!!!
Need primer on that metal, under the paint, or it will rust in no time, or simply rub off, like it was already doing with your first piece you showed being bent.
Added:
That bend should be able to be much sharper. Perhaps a secondary piece to put in that is shaped to be flush with the bending edge? Or just grind down that leading edge of the clamp angle, to sit flat against the base, maybe? And if you want the more curved bends available, make a secondary edge that you can slide under that clamping angle? Not sure, but many of the things I'd want to do with this would require a sharper 90° bend.
Also, you should have some marks along that clamping angle, to square up the piece, and/or center it, so you end up with actual square bends.
Good job
Genial. Gracias!!
Excelente .
Vou já fazer isso AGORA 🕵️
Congratulations!!
without a doubt
Klasse ❤
Great...
Excelente trabajo muy bueno.
Nota 10 viu parabéns
Very nice,
Nice selfmade Tool 👌
merci c'est simple à réaliser !
Muito interessante. Parabéns
Gostei do vídeo.
Thank yu ...EXCELENT
Very good video, very good job sure do like it think I will have o make me one.
احسنت،يامعلم
Exelente
Super
Très bon
Well by golly dat waz awesome
The sheet you bend which millimeter?
Muito bom chou de bola amigo
Amazing!!! Thank you! 💪
I'm Toph now. I'm a bender😊
Hay lắm bạn 🤘