Yep, another brake builder who get's it wrong and the people commenting haven't a clue so make inane comments about how good it is and the best video they've seen! The clamp bar on ALL brakes has to be able to slide way from the point of bend by the thickness of the metal being bent THEN clamped down! I've watched dozens of these videos and only seen one that got it right. One of them had to cut the video at the moment it couldn't reach 90 degrees because the clamp was fixed on the edge! He didn't mention it..... Fine if all you are going to do is bent the same thin tin all the time, it doesn't matter but if you were doing a production run of bends then you need adjustable stops that you can set for whichever thickness metal. It's not rocket science but sadly there are far too many people posting videos on YT for all kinds of things but who are of low intelligence.
This should be easily done by ovaling the holes that mount the clamp bar (on the table side), or adding multiple holes along the bar at different pre set distances. If you're that concerned about production runs, get a production brake. Or this simple mod does the same.
Honestly the best bends I've seen from a diy brake. I was about to mount my hinges on top but I see the logic here. Great job
Thank you very much my friend
Best diy brake I have seen.
thanks 😊
well done brother! Thank you
Best DIY brake I’ve seen
Today I used a hammer, tomorrow I'm building this. Great project.
Thank you very much my friend
@@DIYFixManI'm buying material to build 1 today finally.
Respect. You got a new subscriber.
Thank you very much my friend, I am very happy
Супер станок без сварки
👍❤
Great video
פשוט מדהים! 👌
תודה
You stuff is awesome
🤗❤️
Very nice bender!
Отличная идея!
Gracias por compartir
👏👏👏👏
Thanks
Amazing creativity
Yep, another brake builder who get's it wrong and the people commenting haven't a clue so make inane comments about how good it is and the best video they've seen!
The clamp bar on ALL brakes has to be able to slide way from the point of bend by the thickness of the metal being bent THEN clamped down!
I've watched dozens of these videos and only seen one that got it right. One of them had to cut the video at the moment it couldn't reach 90 degrees because the clamp was fixed on the edge! He didn't mention it.....
Fine if all you are going to do is bent the same thin tin all the time, it doesn't matter but if you were doing a production run of bends then you need adjustable stops that you can set for whichever thickness metal.
It's not rocket science but sadly there are far too many people posting videos on YT for all kinds of things but who are of low intelligence.
¿Can you post the link for the correct configuration? (for the clamp sliding bar)
This should be easily done by ovaling the holes that mount the clamp bar (on the table side), or adding multiple holes along the bar at different pre set distances.
If you're that concerned about production runs, get a production brake. Or this simple mod does the same.
Hi Jonathan
Can you give me the link for the " one who got it right "please as I need to build one of these?
ขอบคุณมาก
روعة
good for bending polycarbonate too
I want to build one specifically for this reason! :)
Nice 👍
Thank you 🤗
制作的原理很详细了,再把材料说一下会更好。
Very talent person
За гайки с ушками - like.
Very good 👍 👍 👍
thanks buddy
Excelente muy bueno saludos desde Argentina
❤️
Very nice, ThankQ
Thanks 🤗
Very nice good job sir
Thanks 🤗
👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
👏👏👏👏👏👏💖💖💖
❤️❤️❤️❤️
Hey other universe.. bite my shiny merel.. woops got the wrong bender... 😂
Достойно
Mande as medidas da drobadeira quero fazer uma 2:20 por 1'50 pra dobrar chapa de 1'8
С такой штукой я бы тоже гнул всё подряд 😀👍
I guess... if your sheet metal is only 15" wide.
too much free time my friend
из за рояльной петли там не будет 90 градусов
He must like radiation burns on his hands
Pero como puedes trabajar sin guantes !!!
Si pero dobla una pieza de 20' ????
freezing / cooling down the aluminum to make it harder for a cleaner cut is something 99% of men fail to do
Who cares.
Plenty of ways to clean it up afterwards.
Who has a freaking freezer in their shop.
can you gift detail specifications?
А Федя ломик об каленку гнул
Thank you 🤗
Oui c bonne
Ненужная херня. Тупо можно в тисках все загнуть.
No hay esa bisagras
There are hinges
👏👏👏👏
Thanks