2008 Honda Fit thermostat Replacement

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 21

  • @jesushuerta1852
    @jesushuerta1852 2 ปีที่แล้ว

    Left out rtv sealant. Removing battery as well as hoses attached to housing will make job much easier. Also, that box connector on wire harness is removed using a flat blade screwdriver beneath box. Pry down on latch underside and pull box out.

  • @snapringchronicles3020
    @snapringchronicles3020 3 ปีที่แล้ว +1

    When I did this I also put some RTV silicone to form a gasket around part of that thermostat housing

    • @prabhakarrao4922
      @prabhakarrao4922 4 หลายเดือนก่อน

      Does absolutely no harm done but I can assure you that it is not necessary.

  • @MrJohnnyDistortion
    @MrJohnnyDistortion ปีที่แล้ว

    Which temperature is the thermostat?

  • @jamesrobnett3590
    @jamesrobnett3590 3 ปีที่แล้ว +1

    Hey, thanks for putting this video up! It was very helpful since my CDROM service manual wasn't working. We got stuck on removing the wiring harness and I made a short video for that since I saw a lot of other people got stuck on that as well. Anyway I can link that video to yours? Thanks again for this write up!

    • @megpie9971
      @megpie9971 2 ปีที่แล้ว +1

      Where is that video of the harness taking it off please? HOW DO YOU GET HARNESS OFF ONE STUPID PIECE HOLDUNG ME UP!

  • @mkrp4
    @mkrp4 4 ปีที่แล้ว

    I took the thermostat housing without disconnecting radiator hoses but took out heater hose (shown at 3:23)

  • @caseystyer2996
    @caseystyer2996 2 ปีที่แล้ว

    How d f did you free up that dead end connector?

    • @GOTJESUS88
      @GOTJESUS88  2 ปีที่แล้ว

      I unplugged and unlatched as much as I could for wiggle room

  • @zacinnc78
    @zacinnc78 3 ปีที่แล้ว

    what is that hose @2:05 ?

    • @mkrp4
      @mkrp4 3 ปีที่แล้ว

      Fresh air hose for PCV system

  • @Mamiigly
    @Mamiigly 2 ปีที่แล้ว

    Hello how did you remove this?

    • @GOTJESUS88
      @GOTJESUS88  2 ปีที่แล้ว

      Remove what?

    • @Mamiigly
      @Mamiigly 2 ปีที่แล้ว +2

      How did u remove all the electical thing before you can get through the thermostat? can you make video how did you remove all the pain in the butt stuffs? i mean all the wires and stuffs before you can reach the thermo i wanna see how you remove all those

    • @bezizwedlamini1575
      @bezizwedlamini1575 ปีที่แล้ว

      @@Mamiigly you don't deserve a response...let alone fix a car...with those type of questions

    • @midna5214
      @midna5214 8 หลายเดือนก่อน

      @@MamiiglyTheyre just supposed to pull out, I mean they have clips but mine was shit. Was being too gentle with it

  • @jsmith6259
    @jsmith6259 3 ปีที่แล้ว

    Thanks mate

  • @sydwelltlhola4211
    @sydwelltlhola4211 3 ปีที่แล้ว

    do you know the torque measurements to tighten?

    • @GOTJESUS88
      @GOTJESUS88  3 ปีที่แล้ว

      I do not. I’m sure their is a rite up somewhere on google for it. I just tighten them up ever so much.

    • @MrJohnnyDistortion
      @MrJohnnyDistortion ปีที่แล้ว

      Until it is snug. Until the bolt doesn't turn anymore. Maybe 1/8-1/4 turn after it stops. Aluminum cracks if it's over tightened.

  • @Adri_57
    @Adri_57 3 ปีที่แล้ว

    It’s called a WASHER!!!!