About weighing the lid down: you only need to do this at the very beginning, because all you need is for the console to recognise that there is indeed a readable disc inside. Once that has been established, you can remove the weight, and the game will play perfectly fine.
@@buggaluggachug9570 The PS2 is indeed a strange beast. Some games on my quirky PS2 slim will load and play just fine without needing to do anything with the lid at all. Others require me to push the lid down for them to load. Others still require me to push the lid down, release when the disc starts to spin and then press down again. And some are almost hopeless to get going at all. And these are all PS2 DVD games, none of them platinum. And all of them spotless, without a single smudge or scratch (I take good care of my games). I have no idea why some games are more trouble than others.
You saved my ass! I thought i was being clever by glueing down the door sensor. Made the same mistake and after watching this, bought a soldering iron for £12 and did the fix. Super easy and much more stable than the straw technique. I also unscrewed the disc brake (and kept it safely somewhere) so there's no need to tape that down as it doesn't last that long. Thanks!
Does it play other game cds? If it plays nothing but it does spin, it could be the lens or the disc has a deep scratch or the lens is eventually going bad. Its cheaper to replace the lens because its only like $10.
For all of you, I first recommend adjusting the potentiometer. If that doesn't work, it's most likely because your laser has weakened and needs to be replaced
Who else is returning to his old console because of the coronavirus? edit: my god... so many.. i wrote this half year ago lol btw my ps2 still not working even after this video.. so.. have fun everyone
An alternative to the big blob of solder would be to solder small wire to connect all 4 of those pins. You could also use lead clippings from resistors if you have any laying around. I usually don't do a solder blob only because you risk leaving a burn mark on the board.
This actually helped. I pressed down and the clips went back in place. My issue was minor. Just fixed my ps2 watching you. Good tutorial bro ! Thanks 🙏
Ok, so I just bought Persona 3 (Original, in case anyone was wandering) and I put it in to my PS2 Slim, and it wont turn on. Hope this video works... It started to work when I put weight on the top! Thank you! I now need to waist 65 hours of my life...
Bas van Delft I think this has happened to me before as well I used my fat Ps2 my dad got me off of EBay but recently I knocked the Graphics card loose in it so now the picture is out of wack when I use it.
Thank you so much, it WORKED !! I bought recently used PS2 in very good condition, stored for 7 years in previous owner's closet. 2 of 6 games worked perfectly, 4 nothing - cant read the disc. Thanks to you - very easy solution :)
You are amazing! We(me and my dad) opened it up and followed your instructions, after it did some attempts to read the disc but then stopped spinning again it worked flawlessly! You gave me a wonderful gaming night with my dad! Thank you!
I can’t even get into the damn thing, the screw just won’t come out. I’m about to lose my mind, I have no internet and I can’t go anywhere because the world is going to poop
Your screws might be stripped. Did you ever get them out? There are tutorials for removing stripped screws on the internet. I assume you were following righty tighty, lefty loosey?
Amazing fix!!! It took all of 20 minutes to open, crush that little button & remove the pieces (quicker than de-soldering), make a solder ball to connect the points, put it back together, and -BOOM- a working ps2 slim. Such a smart & easy fix. Why in the world did the even have that button?!?
I think its there to check when the lid is closed, to prevent people from doing disc swap tricks and other nonsense. There's probably multiple sensors that detect if the lid is closed
I had this issue after digging out my childhood ps2 from my aunts house. I tried cleaning the laser reader, no luck. I tried to tilt the ps2 vertically and it worked perfectly fine after that. Maybe try that first before digging in just in case.
I've found with mine it was the front switch that was the culprit. I found putting some tape under the power button board (underneath the switchboard on the plastic casing), this gave it some leverage to hit the button on startup. helped with my issue completely.
My PS2 just came in today and after putting 3 disc in that couldnt be read I was getting worried. Tried the first trick of flipping it upside down and it worked immediately! Genuinely, thank you so much! ❤🎮
Dude! You saved my PS2 slim! I also suck at soldering but I went for the switch removal/soldering permanent fix and it worked like a charm! I had to rework the blob of soldering about a dozen times but finally got it to work. I even got the blob to look like I knew what I was doing from the start. lol
Another tip, before prying up on the part you're desoldering make sure to lightly push on the side of the part to make sure the solder is melted and the part is loose. I've ripped many pads off boards when I was just becoming an electronic tech.
Haven’t had to do a “repair” in almost 8 years. And it makes me want to go try this again to an old one I have in a spare room put away because I didn’t think it worked, which I don’t know why I still have, like many people. 8 years of no problem, 1 hour of cursing the books I would’ve read for a couple hours in place of plying ,and only 2 seconds of swabbing the lens quickly. So nice when suggestions work. Everything you see in this video... I can’t stress enough, stop!!!!! Stop! It’s amazing, maybe only mine and other people with super minor problems... 2 second non hard swipe of a clean cotton swab, q-tip to the lens and its back.
Fish Bee.... You the dude. i have been trying to play FF 12 for 3 weeks now. And something as simple as putting a weight on the back of my PS2. It started. Thanks this video is awesome.
I’m glad I found this vid cause a few months back my Slim PS2 was working perfectly fine until I put my Atv Quad power racing 2 disc into my Ps2 and that’s where the Disc read errors started stupidest part about it that one of my games what was working was the Cult Classic SSX3 where I was on peak 3 with Mac Frazier and Allegra Sauvgess with no cheat codes used and I also got my first platinum medal on Much-2-Much peak 3’s Big Air event with both Mac and Allegra. But I think I have another issue involving the thing that spins the discs it seems to slow down and starts possibly rubbing on something at the front of my Slim Ps2 disc tray and also it reads some of my blue coating Discs but doesn’t start up the game takes me back to the screen with my Memory Cards on it. Also even prior to my disc read error issues some of games didn’t even work them being the Cult classics of NFSUG1 and 2 and some of the Burnout games what’s weird cuz a few years ago my Slim Ps2 loaded up Burnout Revenge perfectly fine . Also my Burnout 3 also worked but it made my Ps2 make weird sounds made the Disc scrape on the Disc tray cuz it made the disc spin really fast and I didn’t even have the disc speed on fast
i finally know the reason guy. i took out my ps2 this morning, plug everything then my ps2 slim work perfectly (today is 02/13th/2019). at fisrt, i conected it to my old fat Lg 21' tv - it worked perfertly. then i changed to my 32 lcd. it nor read disc and had a weird noise this time. i tried everyways found on gg, but useless. then i remember that i changed the adapter. i had 2 ps2 adapter : 1 is 8.5V - 5.6A ; 2 is 18.5V - 3.5A. and the 1 is work. so try this, it can help you to live you childhood again.
My PS2 Slim doesn't recognize the disc format, and sometimes doesn't read the disc at all. My fix? Put it upside down. Problem solved! An old trick, but it works in my case. Hope it lasts!
Update: well that trick DID work for a while, but I'm still getting disc read errors every now and again. Perhaps it's time to legitimately repair this thing....
This helped a lot thank you. I thought I bought a fake copy of a very rare ps2 game because all my games were read except that specific one… I opened up the ps2 and taped down both black buttons in the video and it started playing ! Thank you I would be devastated if it didn’t
Dude! Thank you brother. Bought a slim for my brothers birthday because we grew up on PS2. That was our childhood. I bought it off some website and it would on and off work, very frustrating. Solution #3 worked for me!!!! You the man.
I found my ps2 after 12 years of it being in a box and just found 3 of my favorite games “MK Shaolin monks” “Pac man World 2” and “Batman rise of the sin tzu” The upside down method works good but im afraid of the disc getting srcatched just making sure as long as it cause no damage to the disc or the console itself, other than that thanks for the Video😁
oh dude thank you so much. just tried to use my old ps2 and hadn´t played for like 6 years or more. the trick with the tape worked well and my motor is working again. much love
Solid tips, although none of them applied to my console i ended up cutting the little soring loaded disc stopper because it was creating too much friction for the disc to spin.
Yooooo awesome just fixed mine was that back switch just broke away the plastic and put some solder and it’s now working after stopping 5 years ago cheers bro
Ur video really helped me out it was the only video that knew what to do and all the other videos that I watched didn't help but ur I really that u cause I thought I was gonna never play it again🙏🏽🙏🏽🙏🏽🙏🏽💯💯💯
My ps2 does read some discs perfectly fine even though they have some scratches but, when I play a clean copy of Socom 1 or Gran turismo 3 the disc stops spinning occasionally
I had problems with ps2 when i had it till i got ps3 and ps4 ps4 is still a good machine over 10 years since i brought it its still works like a beauty.
Thx Bro, great intel. The used game store I got mine didn't have the screw on very tight in the back where it says if you remove the sticker that the warranty will be voided. Makes you wonder if they did that on purpose to get the user to come back so they'll spend more money.
Lol dude this is the sneakiest shit ever. "Oh I've never done this before, oh gee wizz look my warrantee sticker including serial is still there. NEVER DONE THIS BEFORE, nothing to see here, officer." i love it
Bought a used ps2 on amazon a few days ago (dumb move, I know), it's supposed to come in a week or two so I'm just watching this video in advance because I know discs not getting read is a common issue lol
Thank you for this video I jus hooked up my ps2 again after thinking it was unfixable for a while jus to see if I could do something and this video really helped me now my discs load consistently. Sometimes it don’t work but for the most part it does😁
I just had this issue. Took it apart and tested to see if the disc would spin and it did. Apparantly just doing that fixed my issue when I put it back together again. Either that or because I made sure the screws for the disc cover were nice and tight so it had very little give.
I have not played Shadow of the Colossus since I was in high school, and I have been desperately trying to get my hands on a copy because I’m broke and I don’t have the money for a PS4, plus I lost my PS2 copy years ago. So i convinced my brother to give me the old PS2, and here I am booting it up, to see if it works, so that I can buy a used old copy from eBay. Then, digging in a drawer in my parents house, I FIND MY OLD COPY- so I am ECSTATIC, I put it in the old PS2, and am thinking “finally, after a decade of waiting, I can finally play this old classic again,” and then… “the disc could not be read.” TH-cam, save me Update: it worked:)
I actually had this problem and this is a very helpful video but actually I'm more interested in the music you're using. Is it proprietary or did you pay for it from somewhere? Really cool if you could let me know. Thanks.
My laser just comes down even when i touch its sensor . i have removed the lid off and have done as you did . But the laser still comes down with pressure . It doesnt have sensor problem nor is motor damaged . But the cd wont spin and laser comes down and makes noise . what do i do? Ihave ps2 slim
Thanks so much for this helpful video! I used dollops of hot glue applied with the ends of uncooked fettuccini noodles to hold down the switches which were handicapping my ps2! Getting the application motion right was a little difficult, not sure I recommend this method.
Such a helpful video! My disk spins fine, but after a while the ps2 has a hard time reading it, and this happens with most of my games. I'm thinking it might be the laser but i'm not very good with this stuff so i'm not sure
Wow! Thank you. It is working. I've put my huge Bible on top of my PS2 and it now is reading the game disk. Your proverbial miracle....lol Guess what I'm playing.....NFS: Underground and NFS: Underground 2
Dude thanks for your advice it actually worked I put weight on top of my ps2 console and it read the disk you saved me the hassle of opening it or buying a new ps2 thanks I just wonder if it doesn't affect the console if you use it upside down
Omf- You have made me the happiest girl to ever live!! I tried the tape method and it worked wonderfully! I got my ps2 for $5 at a garage sale and I always had to add weight for it to work but sometimes it didn't work. You just saved me some money! I was about to give up and buy a new one.
Removing the switch and applying a solder blob might be time consuming, but definitely the best long term fix.
About weighing the lid down: you only need to do this at the very beginning, because all you need is for the console to recognise that there is indeed a readable disc inside. Once that has been established, you can remove the weight, and the game will play perfectly fine.
depends on the game entirely. other games have loading screens within the game, those wont work.
@@buggaluggachug9570 The PS2 is indeed a strange beast. Some games on my quirky PS2 slim will load and play just fine without needing to do anything with the lid at all. Others require me to push the lid down for them to load. Others still require me to push the lid down, release when the disc starts to spin and then press down again. And some are almost hopeless to get going at all. And these are all PS2 DVD games, none of them platinum. And all of them spotless, without a single smudge or scratch (I take good care of my games). I have no idea why some games are more trouble than others.
@@Gilmaris haha right. i just fixed mine. just used duct tape on the part he said!
@@buggaluggachug9570 I already did. Still I need to coax it in order to read certain games.
@@Gilmaris im sry :( ya i just ordered one from amazon and they sent it all busted and shit. like seriously wtf. but its all good. got it working.
When dealing with electronics, never use the "hope" method...can easily result in grey smoke escaping. ; )
And replacement smoke is really expensive and hard to come by. Best i have been able to source is Lucas OEM wire harness smoke. ;P
You saved my ass! I thought i was being clever by glueing down the door sensor. Made the same mistake and after watching this, bought a soldering iron for £12 and did the fix. Super easy and much more stable than the straw technique. I also unscrewed the disc brake (and kept it safely somewhere) so there's no need to tape that down as it doesn't last that long. Thanks!
This better work cuz I want to be able to play grand turismo 4 with my dad again
Slavic Humor that’s what im here for
Same
i play that too
@Strange things are happening to Woody how do you know if thier double layered my slim reads some disc's and not others could this be why
Same tho
My CD spins alright, but after a few seconds it says "The disc could not be read."
same but not for games
Does it play other game cds? If it plays nothing but it does spin, it could be the lens or the disc has a deep scratch or the lens is eventually going bad. Its cheaper to replace the lens because its only like $10.
For all of you, I first recommend adjusting the potentiometer. If that doesn't work, it's most likely because your laser has weakened and needs to be replaced
Mě tooo
Me too
Who else is returning to his old console because of the coronavirus?
edit: my god... so many.. i wrote this half year ago lol
btw my ps2 still not working even after this video.. so.. have fun everyone
Mee to bro
Me
Yeah me too
Yep. Gettin’ my Final Fantasy XII on!
Man y'all too!?!?! I just plugged mines in and started playing some NFS Underground 😎
I turned it over, and turned it back around and it worked. I could play kingdom hearts again ✊ omg I was shook
This is EXACTLY why I’m trying to fix mine 😭
An alternative to the big blob of solder would be to solder small wire to connect all 4 of those pins. You could also use lead clippings from resistors if you have any laying around. I usually don't do a solder blob only because you risk leaving a burn mark on the board.
This actually helped. I pressed down and the clips went back in place. My issue was minor. Just fixed my ps2 watching you. Good tutorial bro ! Thanks 🙏
Mate we looked at your video and laughed at the dumbbell idea.Long story short we placed a dumbbell and it worked.Thank you for making my life great
Is it working right now ?
finally my problem solved..buy another one.
Bought 3. The rrod of it's time for sure
Lol
When i open ps2 or reset ps2 or put a cd, it makes a drrrrt sounds
Same with mine
mine too
Yes same sad face
@@novasclipdumb6987 did you clean the fan?
When i opens my ps2 it is only loading can anyone tell me what can i do
The idea of putting something on top was actually smart, and is sounded like my ps2 was working again. I need to see the video output though!
Ok, so I just bought Persona 3 (Original, in case anyone was wandering) and I put it in to my PS2 Slim, and it wont turn on. Hope this video works...
It started to work when I put weight on the top! Thank you! I now need to waist 65 hours of my life...
My ps2 stops reading the disc and a few seconds later it reads the disc and then stops reading and then reads the disc.
Same fam
i didn't play it for a while and it doesn't have the problem anymore.
So that's how you solve the problem?!
Minds the same
Bas van Delft I think this has happened to me before as well I used my fat Ps2 my dad got me off of EBay but recently I knocked the Graphics card loose in it so now the picture is out of wack when I use it.
Thank you so much, it WORKED !! I bought recently used PS2 in very good condition, stored for 7 years in previous owner's closet. 2 of 6 games worked perfectly, 4 nothing - cant read the disc. Thanks to you - very easy solution :)
what worked?
YESSS the third solution worked now I can play gta san andreas,juiced 2 and alot of other stuff back!
You are amazing! We(me and my dad) opened it up and followed your instructions, after it did some attempts to read the disc but then stopped spinning again it worked flawlessly! You gave me a wonderful gaming night with my dad! Thank you!
Awesome, glad I could help!
I can’t even get into the damn thing, the screw just won’t come out. I’m about to lose my mind, I have no internet and I can’t go anywhere because the world is going to poop
Hang in there bro!
Your screws might be stripped. Did you ever get them out? There are tutorials for removing stripped screws on the internet.
I assume you were following righty tighty, lefty loosey?
Jae go to Walmart and buy the $20 variety screw pack and try all, it took me an hour even with that
Jae go to Walmart and buy the $20 variety screw pack and try all, it took me an hour even with that
@MateoThe Pro
I was on my phone using data at the time. I didn’t have internet on my PC so I couldn’t play games on there lol
Ur weight idea along with the breakdown of the console, which I mostly did the dusting, helped me fix my PS2 8 years later. Thank u.
Nice!
Amazing fix!!! It took all of 20 minutes to open, crush that little button & remove the pieces (quicker than de-soldering), make a solder ball to connect the points, put it back together, and -BOOM- a working ps2 slim. Such a smart & easy fix.
Why in the world did the even have that button?!?
I think its there to check when the lid is closed, to prevent people from doing disc swap tricks and other nonsense. There's probably multiple sensors that detect if the lid is closed
I had this issue after digging out my childhood ps2 from my aunts house. I tried cleaning the laser reader, no luck. I tried to tilt the ps2 vertically and it worked perfectly fine after that. Maybe try that first before digging in just in case.
Thank you so much! I hadn't used my old PS2 in years and with the help of your video it worked like new :D
I've found with mine it was the front switch that was the culprit. I found putting some tape under the power button board (underneath the switchboard on the plastic casing), this gave it some leverage to hit the button on startup. helped with my issue completely.
My PS2 just came in today and after putting 3 disc in that couldnt be read I was getting worried. Tried the first trick of flipping it upside down and it worked immediately! Genuinely, thank you so much! ❤🎮
Its not working for me, when I reset I am getting black screen when I insert cd and without CD I can see option plz help
@@gamerxnoob9913 hi
Dude! You saved my PS2 slim! I also suck at soldering but I went for the switch removal/soldering permanent fix and it worked like a charm! I had to rework the blob of soldering about a dozen times but finally got it to work. I even got the blob to look like I knew what I was doing from the start. lol
I held my hand on top of the disc cover pushing it down lightly while I booted it up and it worked
Same with mine too. I thought it was the release catch on the front tho.
Pressure at the back worked like a charm. THANKS!😊😊😊
Another tip, before prying up on the part you're desoldering make sure to lightly push on the side of the part to make sure the solder is melted and the part is loose. I've ripped many pads off boards when I was just becoming an electronic tech.
Thanks man so helpful, I already managed to open my ps2 but those tiny safety buttons seemed to not be fully pressed so now I can fix my problem
Haven’t had to do a “repair” in almost 8 years. And it makes me want to go try this again to an old one I have in a spare room put away because I didn’t think it worked, which I don’t know why I still have, like many people.
8 years of no problem, 1 hour of cursing the books I would’ve read for a couple hours in place of plying ,and only 2 seconds of swabbing the lens quickly.
So nice when suggestions work.
Everything you see in this video... I can’t stress enough, stop!!!!! Stop!
It’s amazing, maybe only mine and other people with super minor problems... 2 second non hard swipe of a clean cotton swab, q-tip to the lens and its back.
Massive thank you for this video. You just helped me fix my PS2 that I thought I'd have to throw away!,
Glad I could help!
I need help for me my place station 2 repair closing not properly disc could not read my number is 7550251085, anybody service
the tape method in step 3 seriously fixed my ps2’s reading issue. though i got super lucky those two pieces didn’t break off
After blowing 3.14kg of dust of my ps2, I had the same issue and this fixed it. Thank you!
Nice!
Fish Bee.... You the dude. i have been trying to play FF 12 for 3 weeks now. And something as simple as putting a weight on the back of my PS2. It started. Thanks this video is awesome.
I’m glad I found this vid cause a few months back my Slim PS2 was working perfectly fine until I put my Atv Quad power racing 2 disc into my Ps2 and that’s where the Disc read errors started stupidest part about it that one of my games what was working was the Cult Classic SSX3 where I was on peak 3 with Mac Frazier and Allegra Sauvgess with no cheat codes used and I also got my first platinum medal on Much-2-Much peak 3’s Big Air event with both Mac and Allegra. But I think I have another issue involving the thing that spins the discs it seems to slow down and starts possibly rubbing on something at the front of my Slim Ps2 disc tray and also it reads some of my blue coating Discs but doesn’t start up the game takes me back to the screen with my Memory Cards on it. Also even prior to my disc read error issues some of games didn’t even work them being the Cult classics of NFSUG1 and 2 and some of the Burnout games what’s weird cuz a few years ago my Slim Ps2 loaded up Burnout Revenge perfectly fine . Also my Burnout 3 also worked but it made my Ps2 make weird sounds made the Disc scrape on the Disc tray cuz it made the disc spin really fast and I didn’t even have the disc speed on fast
Thank you for that tip. I was thinking about a thing like this but with your video I managed to fix it in a couple of minutes.
i finally know the reason guy. i took out my ps2 this morning, plug everything then my ps2 slim work perfectly (today is 02/13th/2019). at fisrt, i conected it to my old fat Lg 21' tv - it worked perfertly. then i changed to my 32 lcd. it nor read disc and had a weird noise this time. i tried everyways found on gg, but useless. then i remember that i changed the adapter. i had 2 ps2 adapter : 1 is 8.5V - 5.6A ; 2 is 18.5V - 3.5A. and the 1 is work. so try this, it can help you to live you childhood again.
My PS2 Slim doesn't recognize the disc format, and sometimes doesn't read the disc at all. My fix? Put it upside down. Problem solved! An old trick, but it works in my case. Hope it lasts!
Update: well that trick DID work for a while, but I'm still getting disc read errors every now and again. Perhaps it's time to legitimately repair this thing....
Worked first try after turning upside down ! Thank so much dude !
1st and 2nd options both work! Had to turn my PS2 upside down and use a 5 pound weight for extra support
This helped a lot thank you. I thought I bought a fake copy of a very rare ps2 game because all my games were read except that specific one… I opened up the ps2 and taped down both black buttons in the video and it started playing ! Thank you I would be devastated if it didn’t
Nice!
Dude! Thank you brother. Bought a slim for my brothers birthday because we grew up on PS2. That was our childhood. I bought it off some website and it would on and off work, very frustrating.
Solution #3 worked for me!!!! You the man.
Nice, glad I could help!
I turned mine upside down and it worked! Nice one!! Thankyou.
I found my ps2 after 12 years of it being in a box and just found 3 of my favorite games “MK Shaolin monks” “Pac man World 2” and “Batman rise of the sin tzu” The upside down method works good but im afraid of the disc getting srcatched just making sure as long as it cause no damage to the disc or the console itself, other than that thanks for the Video😁
Thanks buddy, you saved me a lot of heartache
omg the weight solution worked for me. Thank you thank you thank you. I've had this ps2 since I was a kid and I didn't want to have to let it go.
You rock, dude! Thanks for the video. Taping down the back button did the trick for me.
Thank you a lot. It took me probably like 10 minutes.
oh dude thank you so much. just tried to use my old ps2 and hadn´t played for like 6 years or more.
the trick with the tape worked well and my motor is working again.
much love
Solid tips, although none of them applied to my console i ended up cutting the little soring loaded disc stopper because it was creating too much friction for the disc to spin.
FishBell thanks man. I’ve had some issues here or there. I didn’t do much but rest my hand on it until it read the disk.
Thank you for the video, the soldering fix worked perfectly for me! :)
Yooooo awesome just fixed mine was that back switch just broke away the plastic and put some solder and it’s now working after stopping 5 years ago cheers bro
Awesome!
The upside down trick works best for me!!!! Appreciate it!!
FANTASTIC. i fixed my father-in-law's PS2. Good, clean vid. Excellent production.
Who are seeing in 2024😂😂
Me
Who is*
IT WORKED thank you so much it really helped
Holy crap putting it upside actually worked, thank you!
Ur video really helped me out it was the only video that knew what to do and all the other videos that I watched didn't help but ur I really that u cause I thought I was gonna never play it again🙏🏽🙏🏽🙏🏽🙏🏽💯💯💯
thank you! was able to fix using tape on the main sensor and a bit of weight on the lid. appreciate ya
You are the 🐐 just fixed it right now since it wasn’t workin last night Started playin Scarface !!
Nice! Glad I could help
My ps2 does read some discs perfectly fine even though they have some scratches but, when I play a clean copy of Socom 1 or Gran turismo 3 the disc stops spinning occasionally
I had problems with ps2 when i had it till i got ps3 and ps4
ps4 is still a good machine over 10 years since i brought it its still works like a beauty.
Thx Bro, great intel. The used game store I got mine didn't have the screw on very tight in the back where it says if you remove the sticker that the warranty will be voided. Makes you wonder if they did that on purpose to get the user to come back so they'll spend more money.
Lol dude this is the sneakiest shit ever. "Oh I've never done this before, oh gee wizz look my warrantee sticker including serial is still there. NEVER DONE THIS BEFORE, nothing to see here, officer." i love it
Congrats, with the weight thing you almost broke my console. Very thanks, much wow, such help.
Very surprised, but this was actually it!
Thank you for the video!
Brooo thank you.. the first step already helped me 😭
Bought a used ps2 on amazon a few days ago (dumb move, I know), it's supposed to come in a week or two so I'm just watching this video in advance because I know discs not getting read is a common issue lol
This was actually really helpful, thanks very much
Sweet! I remember back in the day having those problems. Thanks for the info.
Thanks alot m8. Fixed mine with tape.
just glue the button and problem solved. thanks man you helped a ton
Nice! Glad I could help.
The rear switch was the problem for me. A litle bit of tape and boom, game starts up right away. Thank you sir.
Glad you got it working!
@@FishBeeProductions Well you saved me pointlessly buying a new laser for it so thank you.
Thank for tip. I didn’t fix but just power with stick. Disc till move ! Final and u make me happy! U r best fix
Splashdown!! Great choice
Thank you for this video I jus hooked up my ps2 again after thinking it was unfixable for a while jus to see if I could do something and this video really helped me now my discs load consistently. Sometimes it don’t work but for the most part it does😁
Glad I could help!
@@FishBeeProductions I do have one question what should I do if it’s reading the disc but when the game tries to load it’s a black screen
Thank you the weight trick actually worked
I just had this issue. Took it apart and tested to see if the disc would spin and it did. Apparantly just doing that fixed my issue when I put it back together again. Either that or because I made sure the screws for the disc cover were nice and tight so it had very little give.
I have not played Shadow of the Colossus since I was in high school, and I have been desperately trying to get my hands on a copy because I’m broke and I don’t have the money for a PS4, plus I lost my PS2 copy years ago. So i convinced my brother to give me the old PS2, and here I am booting it up, to see if it works, so that I can buy a used old copy from eBay. Then, digging in a drawer in my parents house, I FIND MY OLD COPY- so I am ECSTATIC, I put it in the old PS2, and am thinking “finally, after a decade of waiting, I can finally play this old classic again,” and then…
“the disc could not be read.”
TH-cam, save me
Update: it worked:)
Solid advice and really helped thank you!
Heeeroo!!! The ducttape saved my PS, hahaha. Who would ever expected that? xD **thumbs up bigtimes**
Thanks dude
Your video saved my evening
Greetings from Germany
Awesome glad I could help!
Thank you so much, the weights worked for me
I can’t believe it, but the dumbbell trick seems to be working (note: upside down didn’t work). Thanks!
Getting some san andreqs vibes right there, thanks for the video!
Thanks, glad I could help!
I actually had this problem and this is a very helpful video but actually I'm more interested in the music you're using. Is it proprietary or did you pay for it from somewhere? Really cool if you could let me know. Thanks.
I don't remember offhand which song it is but it is from the TH-cam audio library which is copyright free to use
@@FishBeeProductions Thanks for replying. I'll check it out.
The weight trick worked perfect thanks heaps!
My laser just comes down even when i touch its sensor . i have removed the lid off and have done as you did . But the laser still comes down with pressure . It doesnt have sensor problem nor is motor damaged . But the cd wont spin and laser comes down and makes noise . what do i do? Ihave ps2 slim
What if it spins but still can’t read disc?
Thanks so much for this helpful video!
I used dollops of hot glue applied with the ends of uncooked fettuccini noodles to hold down the switches which were handicapping my ps2! Getting the application motion right was a little difficult, not sure I recommend this method.
Such a helpful video! My disk spins fine, but after a while the ps2 has a hard time reading it, and this happens with most of my games. I'm thinking it might be the laser but i'm not very good with this stuff so i'm not sure
Flipping the console upside down worked for me!
Wow! Thank you. It is working. I've put my huge Bible on top of my PS2 and it now is reading the game disk. Your proverbial miracle....lol Guess what I'm playing.....NFS: Underground and NFS: Underground 2
Dude thanks for your advice it actually worked I put weight on top of my ps2 console and it read the disk you saved me the hassle of opening it or buying a new ps2 thanks I just wonder if it doesn't affect the console if you use it upside down
I don't think it affects it using it upside down.
Omf- You have made me the happiest girl to ever live!! I tried the tape method and it worked wonderfully! I got my ps2 for $5 at a garage sale and I always had to add weight for it to work but sometimes it didn't work. You just saved me some money! I was about to give up and buy a new one.
Awesome!
I TRY'D it TOO and it worked for me , i was so HAPPY!! Yes!
You save me tons on money man, Thank you so much!!
Yoooo number 3 worked for me thank you so much