It was a great experience with your awesome presentation. Thank you so much for your great effort and spending your valuable time for the music lovers!!
1/4" plugs and jacks are the most widely used audio connectors, carrying signals with different impedance and voltage which makes them incompatible and could even make some smoke if mistakenly mixed. The two major troublemakers are guitar amp sets and portable PA's, in which 1/4" cables are used to carry high-voltage, high-current powered signals that'll certainly cause a costly and gruesome fireworks show while being wired into any line or instrument level inputs. Or if only one end of a 1/4" cable is plugged into an amplifier, the other end will act as both a stungun and a firestarter.
I appreciate your answer and response but more details and specifics would be super helpful. Why? Only because line level seem or to my understanding that of a specific and often set volt, usually safe, level. Let's talk old school... an amp or even a home integrated amp (tape out) will be a safe outboard line level not carrying higher voltage, thus you could daisy chain even a tape out line level output to another amplifier. Or many amps have line level outs, I.e.; Amp 1 input takes an incoming higher voltage low Impedance signal (doesn't a mic input have a much less Impedance, super sensitive higher voltage too?) And moreover your source guitar, instrument may have a pentiometer which can go from hypothetical 0 to 3, 4, or even 12 volts? Vs, a simple line level out put that might be set at 1.5 voltage or 3 voltage. I'm Not giving criticism, I'm asking for you knowledge. So, if I've an amplifier with a line level out, though fed input is say 12, the out is only going to kick out a safe voltage 1.5 example thus a safe signal to the other amp. I can then control the Amp 2 gain of that line level input with its Pentiometer to the speaker? In the video, he says i can't use a speaker 1/4 cable from instrument to speaker, but I'm assuming he's saying only amp to speaker? But doesn't the speaker 1/4 cable have 1) more conducting copper hence and better insulation making it safer for hot. I get that a speaker cable may be of higher Impedance, thus less resistance, meaning more voltage, but I'm confused as to spark, fire, etc... when you're discussing 1/4 cables. Would you be as so kind to help me understand and in details. I'm into tube amps, solid state amps, biamping and multiple amps. I'm into guitars, guitar amps, and using them. Some equipment, like a bunch of Yamaha monitors, powered, have, line/mic and variable balance pentiometer 1/4 inputs. They also have a line in 1/4 input (can't adjust)...and a XLR input with a balance line/mic pentiometer knob. The center, noon is both mic/line and I suppose works as an impede balance. Rotation of the knob, mic way or line way goes to 5 or 7 o'clock. If line side is at 5, pure line. As I rotate to noon, it gets louder. If I rotate into the mic side, distortion. I'm confused too by low htz vs high htz. I see these 1/4 adapters that are XLR to 1/4 inch, they can be use or have different ones that are opposite, low htz to high htz and opposite high htz to low htz? Sorry for novella. If you don't see this post, anyone, please, feel free to chime in. Education is awesome. I appreciate all.
Good elementary tutorial on cables. I particularly enjoyed his visual demonstration of the difference between female connector and male connector. I watched that part several times.
Thanks for the video. It's funny...I've been a musician all my life and never heard of speakon cables. I never used a PA. I always used instrument amplifiers. I recently bought a PA amp and speakers and didn't know that I would need speakon cables. I found out that's what I needed, but had never heard of them. So I watched your video and you answered all the questions and more. Not so complicated now. You make it simple....thanks
Nice and clearly explained and demonstrated Kennis,even us old hands that have seen the changes over the years need to know the subtle differences of the similar looking cables with same ends on but very different cores for their purposes. Well done and worthwhile!
I was looking for some information about 2 RCA Male / 2 RCA Female Piggyback to 3.5mm cables, I have only one of them was wondering if RCA to 3.5 would downgraded the sound L and R audio channel
No. I do it all the time. But you want a decent Y splitter RCA to 3.5mm. Some cheaper ones, have less flexibility... or can be too flexible and a good bend can mess up or cut the break the frayed copper in the line or especially at both points where the RCA or 3.5 mm connections are adhered to the cable. You want a nice snap for feel click/clic when plugging that 3.5 mm into your device, you've then got a good R/L channel connection. Also, consider length... I've some long ones for across the room portable stuff and some shorter ones where equipment will stay put. Peace out.
Thanks for sharing a really comprehensive explanation that's important for musicians to understand, especially for some things that can confuse people like the difference between DMX & XLR or 1/4" instrument & speaker. This is a great starting point for people to learn more and expand their knowledge of the equipment we all gotta use. Quick note on the interconnect vs microphone: interconnects lack the necessary shielding to be used for microphones because they're designed to interconnect devices. Say, your interface to your monitors, which aren't as susceptible to interference. You could use a mic cable as an interconnect, but you'd pick up way too much noise using an interconnect as a mic cable. Appreciate your work & wisdom as always, Kennis!
Super informative and easy to follow, thank you! Also, I love how you showed headphones with 3.5mm cable to plug into your phone, which most smart phones don't have any more. 😅
Standard XLR cables are usually 22-24 gauge and are good for transmitting line level signals to powered speakers. Passive speakers connect to amplifiers, which have peak power. SpeakON cables are designed specifically to transmit speaker level signal from an amplifier to a passive speaker. When you said XLR can be used in speakers did you mean powered speaker? SpeakON cables will be overkill for a powered speaker however. Correct me if I am wrong but comparison between SpeakON and XLR is like apple and orange comparison.
I'm a videographer and I've been struggling to understand the mechanics of sound and audio. I need a basic understanding as I will soon be plugging into sound systems for high quality recording at live events. This video has been incredibly helpful. Thank you so much!
Speaker cables can transfer guitar signal just as good as instrument cables. The reason you don't want to use them is that speaker cables are not shielded and will thus bring a lot of noise into the front end of your amplifiers which will make the interference louder. You dont have this problem going from your amo to your speaker cause ibterference is usually not very loud, especially compared to the signal thats going through it at that moment
Speakon also carries 2 signals. This means that on a lot of modern amps you can set settings for 2 different speakers (woofer and tweeter for example).
corrda1993 no this means you can run a biamp speaker, if you use nl4 spliter’s you can do that but it’s u comon. Most people only use 2 of the 4 legs in the speakon, infact when you buy it sometimes it’s only 2 wires not 4 you would need 4 wires two run a speaker in bi-amp larger scale pro audio systems use a speakon nl8 cable with 8 wires/conductors in it. Depending how the rig is wired and the amps are wired this sometimes caries both signals. Most of these sized systems become 4-5 way systems so sub, low, mid, hi. Sometimes a mid high. The same cable may be used but each one will be running a different signal
it depends on whether it is NL2, NL4 or NL8. NL2 has two contacts so you can only use a cable with to conductors which transmit one speaker signal. If you have an NL4 plug that is also hooked up to a 4-conductor cable, you can transport 2 speaker signals and NL8, which is physically much bigger can transport 4 speaker signals. So when you have two speakers that should receive a different signal, you take an NL4 cable to the first one and then you need to use a crossover cable (or splitter) for the other speaker. The reason being is that Speaker 1 is only going to use the signal on pins 1+ and 1-, and speaker 2 is also going to only use the signal from those pins, but because the signal for speaker 2 has so far been transported on pins 2+ and 2-, you need a cable that takes what is on pins 2+ and 2- and puts it onto pins 1+ and 1-, which is a crossover cable. I don't think these are commercially available, and another option is to hook up a splitter to the free speakon jack on speaker 1 and connect your normal speakon cable to that. @techtutorialsbyhenry : nope, this will not work. Speakon cables are only designed for transporting a speaker level signal between an amp and a passive speaker. An active speaker wants a line level signal to amplify in its integrated amp and has an XLR input for this purpose. Converting speakon to XLR and putting a speaker-level signal into the electronics would likely fry the active speaker's amp. The only case where you can hook a passive speaker up to an active one is if the active speaker's integrated amp is designed to drive another speaker, in which case the active speaker would already have a speakon out and no splitter would be needed. However, I am aware of no such speaker because it would not make sense to build it.
2020, this is the best simply put yet highly informative video ever, you just earned a sub, thank you Ken, beautiful stuff i love how you differentiated the different uses of what seems to be 100% identical types of cables, im in the media ministry in my church and I found this highly useful
I just want to say thank you for all that information on cables. I am buying some equipment for my studio and I had no clue what to buy or what any of this known cables did or where used for other than the basics. This video has taken me out the dark much appreciated.
XLR vs DMX is not about ohmage but impedance. XLR carry low frequency signal, this is not an issue. DMX in the other hand uses serial communication at a fixed 250kbps baud rate. You need a special wire conception to avoid problem related to higher frequency. It's also why it's best practice to use a terminator on a DMX bus. It's also why you can use CAT5 or CAT6 cable as DMX cable because they are built to deal with high frequencies.
I learned something new. With xlr cable I wasn't aware of the difference for digital vs mic/audio. I was experiencing alot of hum and interference with some cheap cables and stepped up the quality and solved the problem. Thanks for sharing.
Sweet.... I'm having an extension built... I want to have speakon wall sockets... So do I just Daisey chain them... IE output from amp going into Left channel input in the wall, then from that initial input Daisey chain one speakon socket to the next.... Repeating the process for the right channel....
Some of the RCA connector are used for Composite Video - Red Blue and Green; while the typical Yellow - Video, Red and White for Left and Right Audio. Midi are DIN Connectors like on the old Commodore computers.
Great video, I was really confused whether there were two types of XLR cable, one for mics and DIs which are inserted into a mixing console, and one for the the output which goes into amps and speaker cabs but if I understood correctly this is not the case.
Hi. I have a PA system with 2 speakers. I’m trying to add another passive speaker (bigger with bigger subwoofer for bass) that has 1/4” and speakon connectors (both). Right now until I figure out how to connect all together I’m using the small active speaker with the big one. I have been checking the speakon splitters and thinking if that would work if I connect it to the small active speaker and then connect the 2 passive speakers to it. Or maybe I would need to get a mixer to connect the big passive speaker to it if it doesn’t work with the splitter. What do you think? What is your advice on this? Thanks for your help and time.
Thanks for the info. QUESTION: I do karaoke gigs and I have power speakers. I do not use an amp. My speakers are plugged into my pro/fx mixer. Wouldn't I get less (or no) interference using instrument cables instead of speaker cables?
I bought an old mic amplifier on Ebay. It has a Bogen label on it but I think it was either put on or it has been altered. The only outputs it has are 2 groups of BNC jacks labeled 25 watts. I have never seen BNC jacks used with audio before. I have been buying old and new amps for 40 years. Any idea what they had in mind?
I'm a musician play various clubs in my lifetime someone told me you could take a microphone cable cut the ends off. install/ solder quarter inch Jack's and on one side leave one of them off and clip it tape it and it'll keep the hum out is this true? old musician hacks? And for other musicians have you ever heard of a hot tap? that's where you take what looks like jumper cable type cables that has outlets on the other end hook them to the club's main Buzz bars on the breaker box so you can get clean power so that neon signs in fluorescent lights won't make noise on your band's equipment/ PA ! with modern-day equipment not so necessary but in the old days we had to do what we had to do , haha...
Kennis russel. I have been working on my set of 2 Surround recievers from the late 80s and early 90s. And what intrigues me is this "GND" Screw connector. WHAT THE FRICK DOES IT HOOK UP TO!? I HAVE BEEN RESEARCHING FOR LIKE-A YEAR NOW. Does it hook up to an Antenna? A Turntable for Vinyl? I DONT KNOW. Please make a tutorial on a GND screw on connector for recievers.
@@willivers4249 Yeah the ground screw is used for record players / turntables which usually have a pair of RCA (white/red or black/red tulip) outputs and a separate wire with a little fork that you connect to the screw before you turn it so it tightens up and holds the fork connected to the screw.
Great information! I am not a musician, but an electronics repair technician. I need to know about every cable out there, both past and present, in order to do repair work. Frank Frank Reiser Video/Audio Service
Why would you use a XLR for a speaker? The XLR is 22AWG. I have never seen a XLR for power to a speaker. I have seen a XLR to a powered speaker, this just sends balanced audio to the speaker for the amplifier in the speaker. Oh, the old Bose had them. That's been 25-30 years ago.
PLEASE EXPLAIN WHAT IS A TIFFANY STYLE RCA CONNECTION, MOST AMPS COME WITH TIFFANY STYLE RCAs BUT NO INFO HOW TO CONNECT THEM TO HEAD UNIT. THANK YOU MR. RUSSELL
Nice presentation. You may want to add a correction about the speaker cables NOT working in the instruments. The speaker cable has lower resistance and no shielding. It will deliver the signal to the instrument along with all the other interference that affects small voltage and currents like what is delivered to the instrument. The instrument cable on the other hand (much thinner) has high resistance and may overheat if used with the high currents required in the speaker circuit.
Speaking about a TRS male 1/4 inch connector that goes into a mic interface, what would be the proper size? (16AWG, 18AWG, 20AWG, 22AWG, 26AWG, etc??) Thanks a lot!!!
The question I can't seem to find an answer for is. About balanced and unbalanced connections. If your instrument Output Balanced and you have an interface with unbalanced input or vice versa. Does it work either way?
please please help me. I have a speaker vintage with a brown rca Jack pretty sure it's called an rca and there is no brown on my receiver. what colour do I plug it into???
I have balance cable problem , I have to go from 4.4 pentaconn dac output to my Mackie HR824 Mk 2 monitors. I have to two choices Xlr3 pin or balanced 1/4 TS Can you make me a pair 7 feet long
Came across a speakon connector on an old power amp and was utterly flumoxed about how to plug it into the 1/4 inputs on the massive speaker setup i need an adapter.
Hi Could you help me with ( How to repair a cable in which there is a 3.5mm stereo and at the other side there is midi 5 pins ) I am asking about the colour and how to connect 3 cables with 5 cables inside ) Thx
Thank you for this, Kennis. It was really very helpful. That said, I have a question. I decided to check my 1 month & 10 day old "speaker" cables (used to connect my home studio Tannoy monitors to my Mackie mixer), and the 6' Pearstone (TRS to XLR/M) cable says "Professional Microphone Cable" on it. I mentioned the age because it's a week and a half past my 30 day return window :( Is this ok? You mentioned instrument cables are not recommended for speaker connections because they'll get hot, may cause damage, etc.... Should I change the cables? Note, due to a recently rigorous schedule, I have not yet plugged up and tested any of my new cables or the new mixer.
1/4" connectors were designed to convey signal, not current. They simply don't have the surface area at the point of contact to efficiently transmit power. The fact that they became so common for speaker connections in some market segments (mainly guitar amps but also pro audio) is mildly baffling but I guess it's just one of those things. 🤷♂ 11:43 Speakon connectors were specifically designed for moving power loads from amps to speakers. They have much more surface area at the point of contact than 1/4" connectors. Even XLR makes more surface contact than 1/4" connectors.
i have a guitar processer(Firehawk fx) and it has 2 XLR out and 2 "1/4"out ...do i need these kind of speakon, xlr,1/4 speaker cable to connect my guitar processor with powered speaker?
....does anyone know if an xlr output connection will also send out power? .....I have a powered subwoofer that has an output xlr connection......I'm wondering if I buy a passive speaker with a speakon input connection and buying an xlr to speakon wire, would it power the passive speaker?
I have a question relating the difference of speaker and instrument cables: i know how the cable itself differs, but is the plug any different? Would it be safe to solder a plug from an instrument cable to a speaker cable? Had to toss one plug from my speaker cable.
Thank you Kennis. I've been searching video to help me out, but not much on TH-cam. Finally! Very greatful!
Thank you for taking time to make this video. Been in audio for 40+years, & as you know, we must stay informed. Thanks for updating my knowledge.
Thanks man. Just starting a new job and I need to know these. Lots of good info and easy to understand.
All those Audio Cables are analog, therefore the quality and condition of the cables will impact the audio quality.
It was a great experience with your awesome presentation. Thank you so much for your great effort and spending your valuable time for the music lovers!!
1/4" plugs and jacks are the most widely used audio connectors, carrying signals with different impedance and voltage which makes them incompatible and could even make some smoke if mistakenly mixed. The two major troublemakers are guitar amp sets and portable PA's, in which 1/4" cables are used to carry high-voltage, high-current powered signals that'll certainly cause a costly and gruesome fireworks show while being wired into any line or instrument level inputs. Or if only one end of a 1/4" cable is plugged into an amplifier, the other end will act as both a stungun and a firestarter.
I appreciate your answer and response but more details and specifics would be super helpful. Why? Only because line level seem or to my understanding that of a specific and often set volt, usually safe, level. Let's talk old school... an amp or even a home integrated amp (tape out) will be a safe outboard line level not carrying higher voltage, thus you could daisy chain even a tape out line level output to another amplifier. Or many amps have line level outs, I.e.; Amp 1 input takes an incoming higher voltage low Impedance signal (doesn't a mic input have a much less Impedance, super sensitive higher voltage too?) And moreover your source guitar, instrument may have a pentiometer which can go from hypothetical 0 to 3, 4, or even 12 volts? Vs, a simple line level out put that might be set at 1.5 voltage or 3 voltage. I'm Not giving criticism, I'm asking for you knowledge. So, if I've an amplifier with a line level out, though fed input is say 12, the out is only going to kick out a safe voltage 1.5 example thus a safe signal to the other amp. I can then control the Amp 2 gain of that line level input with its Pentiometer to the speaker? In the video, he says i can't use a speaker 1/4 cable from instrument to speaker, but I'm assuming he's saying only amp to speaker? But doesn't the speaker 1/4 cable have 1) more conducting copper hence and better insulation making it safer for hot. I get that a speaker cable may be of higher Impedance, thus less resistance, meaning more voltage, but I'm confused as to spark, fire, etc... when you're discussing 1/4 cables. Would you be as so kind to help me understand and in details. I'm into tube amps, solid state amps, biamping and multiple amps. I'm into guitars, guitar amps, and using them. Some equipment, like a bunch of Yamaha monitors, powered, have, line/mic and variable balance pentiometer 1/4 inputs. They also have a line in 1/4 input (can't adjust)...and a XLR input with a balance line/mic pentiometer knob. The center, noon is both mic/line and I suppose works as an impede balance. Rotation of the knob, mic way or line way goes to 5 or 7 o'clock. If line side is at 5, pure line. As I rotate to noon, it gets louder. If I rotate into the mic side, distortion. I'm confused too by low htz vs high htz. I see these 1/4 adapters that are XLR to 1/4 inch, they can be use or have different ones that are opposite, low htz to high htz and opposite high htz to low htz? Sorry for novella. If you don't see this post, anyone, please, feel free to chime in. Education is awesome. I appreciate all.
Thank you for explaining what cables would be good for speakers!
This video is absolutely amazing i needed to know about cables and connectors for my college event and this was such a great help Thank you so much!!!
Good elementary tutorial on cables. I particularly enjoyed his visual demonstration of the difference between female connector and male connector. I watched that part several times.
😳umm what? You “enjoyed his visual demonstration?” 👀😳
Thanks for the video. It's funny...I've been a musician all my life and never heard of speakon cables. I never used a PA. I always used instrument amplifiers. I recently bought a PA amp and speakers and didn't know that I would need speakon cables. I found out that's what I needed, but had never heard of them. So I watched your video and you answered all the questions and more. Not so complicated now. You make it simple....thanks
Nice and clearly explained and demonstrated Kennis,even us old hands that have seen the changes over the years need to know the subtle differences of the similar looking cables with same ends on but very different cores for their purposes. Well done and worthwhile!
I was looking for some information about 2 RCA Male / 2 RCA Female Piggyback to 3.5mm cables, I have only one of them was wondering if RCA to 3.5 would downgraded the sound L and R audio channel
No. I do it all the time. But you want a decent Y splitter RCA to 3.5mm. Some cheaper ones, have less flexibility... or can be too flexible and a good bend can mess up or cut the break the frayed copper in the line or especially at both points where the RCA or 3.5 mm connections are adhered to the cable. You want a nice snap for feel click/clic when plugging that 3.5 mm into your device, you've then got a good R/L channel connection. Also, consider length... I've some long ones for across the room portable stuff and some shorter ones where equipment will stay put. Peace out.
Thanks for sharing a really comprehensive explanation that's important for musicians to understand, especially for some things that can confuse people like the difference between DMX & XLR or 1/4" instrument & speaker. This is a great starting point for people to learn more and expand their knowledge of the equipment we all gotta use.
Quick note on the interconnect vs microphone: interconnects lack the necessary shielding to be used for microphones because they're designed to interconnect devices. Say, your interface to your monitors, which aren't as susceptible to interference. You could use a mic cable as an interconnect, but you'd pick up way too much noise using an interconnect as a mic cable.
Appreciate your work & wisdom as always, Kennis!
Super informative and easy to follow, thank you! Also, I love how you showed headphones with 3.5mm cable to plug into your phone, which most smart phones don't have any more. 😅
I learned a lot, thank you! Just got a audio interface and I needed this video!
@@kennisrussell :D
Standard XLR cables are usually 22-24 gauge and are good for transmitting line level signals to powered speakers. Passive speakers connect to amplifiers, which have peak power. SpeakON cables are designed specifically to transmit speaker level signal from an amplifier to a passive speaker. When you said XLR can be used in speakers did you mean powered speaker? SpeakON cables will be overkill for a powered speaker however. Correct me if I am wrong but comparison between SpeakON and XLR is like apple and orange comparison.
I'm a videographer and I've been struggling to understand the mechanics of sound and audio. I need a basic understanding as I will soon be plugging into sound systems for high quality recording at live events. This video has been incredibly helpful. Thank you so much!
Speaker cables can transfer guitar signal just as good as instrument cables. The reason you don't want to use them is that speaker cables are not shielded and will thus bring a lot of noise into the front end of your amplifiers which will make the interference louder. You dont have this problem going from your amo to your speaker cause ibterference is usually not very loud, especially compared to the signal thats going through it at that moment
Speakon also carries 2 signals. This means that on a lot of modern amps you can set settings for 2 different speakers (woofer and tweeter for example).
corrda1993 no this means you can run a biamp speaker, if you use nl4 spliter’s you can do that but it’s u comon. Most people only use 2 of the 4 legs in the speakon, infact when you buy it sometimes it’s only 2 wires not 4 you would need 4 wires two run a speaker in bi-amp larger scale pro audio systems use a speakon nl8 cable with 8 wires/conductors in it. Depending how the rig is wired and the amps are wired this sometimes caries both signals. Most of these sized systems become 4-5 way systems so sub, low, mid, hi. Sometimes a mid high. The same cable may be used but each one will be running a different signal
Hi. Do you think that speakon splitters work to connect to passive speakers to an active one?
it depends on whether it is NL2, NL4 or NL8. NL2 has two contacts so you can only use a cable with to conductors which transmit one speaker signal. If you have an NL4 plug that is also hooked up to a 4-conductor cable, you can transport 2 speaker signals and NL8, which is physically much bigger can transport 4 speaker signals. So when you have two speakers that should receive a different signal, you take an NL4 cable to the first one and then you need to use a crossover cable (or splitter) for the other speaker. The reason being is that Speaker 1 is only going to use the signal on pins 1+ and 1-, and speaker 2 is also going to only use the signal from those pins, but because the signal for speaker 2 has so far been transported on pins 2+ and 2-, you need a cable that takes what is on pins 2+ and 2- and puts it onto pins 1+ and 1-, which is a crossover cable. I don't think these are commercially available, and another option is to hook up a splitter to the free speakon jack on speaker 1 and connect your normal speakon cable to that.
@techtutorialsbyhenry : nope, this will not work. Speakon cables are only designed for transporting a speaker level signal between an amp and a passive speaker. An active speaker wants a line level signal to amplify in its integrated amp and has an XLR input for this purpose. Converting speakon to XLR and putting a speaker-level signal into the electronics would likely fry the active speaker's amp. The only case where you can hook a passive speaker up to an active one is if the active speaker's integrated amp is designed to drive another speaker, in which case the active speaker would already have a speakon out and no splitter would be needed. However, I am aware of no such speaker because it would not make sense to build it.
Thank you. Answered all of my questions in plain English
Thanks for the help! It’s easy to forget the basics!
2020, this is the best simply put yet highly informative video ever, you just earned a sub, thank you Ken, beautiful stuff
i love how you differentiated the different uses of what seems to be 100% identical types of cables, im in the media ministry in my church and I found this highly useful
I just want to say thank you for all that information on cables. I am buying some equipment for my studio and I had no clue what to buy or what any of this known cables did or where used for other than the basics. This video has taken me out the dark much appreciated.
The 9 year old in me laughed at 1:50
Vinni Lopes lmao, it’s always so funny to watch the “cable Guys” squirm as they explain male and female connecters
. 😂
XLR vs DMX is not about ohmage but impedance. XLR carry low frequency signal, this is not an issue. DMX in the other hand uses serial communication at a fixed 250kbps baud rate. You need a special wire conception to avoid problem related to higher frequency. It's also why it's best practice to use a terminator on a DMX bus. It's also why you can use CAT5 or CAT6 cable as DMX cable because they are built to deal with high frequencies.
I learned something new. With xlr cable I wasn't aware of the difference for digital vs mic/audio. I was experiencing alot of hum and interference with some cheap cables and stepped up the quality and solved the problem. Thanks for sharing.
Good demo on cables & connectors sir
Full of knowledge about connectors, thank you very much
Thanks for taking the time to explain it; I really appreciate it! :)
Great video!! Speakon is a brand too. It's NL4 & NL8
Great video, always good to know what your grabbing and why or why not. Thanks!
Sweet....
I'm having an extension built...
I want to have speakon wall sockets... So do I just Daisey chain them...
IE output from amp going into Left channel input in the wall, then from that initial input Daisey chain one speakon socket to the next....
Repeating the process for the right channel....
I think you may have meant red and _white_ RCA connectors for audio. Yellow is for composite video.
thanks for your time to show your knowledge
Some of the RCA connector are used for Composite Video - Red Blue and Green; while the typical Yellow - Video, Red and White for Left and Right Audio. Midi are DIN Connectors like on the old Commodore computers.
Great Job! I am going to use you explanation to teach my guitar club students. Thank you!
Great explanation about the cables. I learned good lesson about the various types of cables! 👍
Great video, I was really confused whether there were two types of XLR cable, one for mics and DIs which are inserted into a mixing console, and one for the the output which goes into amps and speaker cabs but if I understood correctly this is not the case.
Hi. I have a PA system with 2 speakers. I’m trying to add another passive speaker (bigger with bigger subwoofer for bass) that has 1/4” and speakon connectors (both). Right now until I figure out how to connect all together I’m using the small active speaker with the big one. I have been checking the speakon splitters and thinking if that would work if I connect it to the small active speaker and then connect the 2 passive speakers to it. Or maybe I would need to get a mixer to connect the big passive speaker to it if it doesn’t work with the splitter. What do you think? What is your advice on this? Thanks for your help and time.
Thanks for the info. QUESTION: I do karaoke gigs and I have power speakers. I do not use an amp. My speakers are plugged into my pro/fx mixer. Wouldn't I get less (or no) interference using instrument cables instead of speaker cables?
Great Video! You made it easy enough for your old PCH choir buddy to understand! Thanks for the info! -W
I bought an old mic amplifier on Ebay. It has a Bogen label on it but I think it was either put on or it has been altered. The only outputs it has are 2 groups of BNC jacks labeled 25 watts. I have never seen BNC jacks used with audio before. I have been buying old and new amps for 40 years. Any idea what they had in mind?
Great video Kennis! Very informative.
Thank you.. one of the greatest explanations bruh
I'm a musician play various clubs in my lifetime someone told me you could take a microphone cable cut the ends off. install/ solder quarter inch Jack's and on one side leave one of them off and clip it tape it and it'll keep the hum out is this true? old musician hacks?
And for other musicians have you ever heard of a hot tap? that's where you take what looks like jumper cable type cables that has outlets on the other end hook them to the club's main Buzz bars on the breaker box so you can get clean power so that neon signs in fluorescent lights won't make noise on your band's equipment/ PA !
with modern-day equipment not so necessary but in the old days we had to do what we had to do , haha...
Thank you! I was using a guitar cable to hook up my speakers for dj and I did not know that 1/4inches are not the same simply cause the ends match...
Kennis Russell thank for post this video it has give me some insight on auto cable,
Still a lot to absorb, (yeah I'm slow) but I plan on watching this several times LoL. Thank you very helpful. 🏹🤠👍
In Ireland and the UK we call the quarter inch or guitar cable a "Jack to Jack" or "Jack lead"
Very helpfull. Watching from dubai
Kennis russel. I have been working on my set of 2 Surround recievers from the late 80s and early 90s. And what intrigues me is this "GND" Screw connector. WHAT THE FRICK DOES IT HOOK UP TO!? I HAVE BEEN RESEARCHING FOR LIKE-A YEAR NOW. Does it hook up to an Antenna? A Turntable for Vinyl? I DONT KNOW. Please make a tutorial on a GND screw on connector for recievers.
GND stands for Ground. (I'm certain)
It's for connecting a ground line which can be for safety or to prevent noise. (I'm almost certain)
I found out already.
It hooks up to a phonograph player to a stereo reciever to do the thing that you said it does.
@@willivers4249 Yeah the ground screw is used for record players / turntables which usually have a pair of RCA (white/red or black/red tulip) outputs and a separate wire with a little fork that you connect to the screw before you turn it so it tightens up and holds the fork connected to the screw.
Can you use a guitar cable to connect powered speakers from the mixer in an emergency?
I love u bro! Had no idea what a speakon cord was. I order a set of $600 speakers and they came with no cords lmao
I bought a krk rokit 7 g4 pair. U know what cables I need?
What about the 3ft cable that has 1/4” end connector to speak on end connector. Where is it rightfully use for?
Great information! I am not a musician, but an electronics repair technician. I need to know about every cable out there, both past and present, in order to do repair work.
Frank
Frank Reiser Video/Audio Service
I think I’m using the wrong connectors for my Rokit 10” 😓 1/4 I get static time to time. So should I switch them with the XLR male ?
Why would you use a XLR for a speaker? The XLR is 22AWG. I have never seen a XLR for power to a speaker. I have seen a XLR to a powered speaker, this just sends balanced audio to the speaker for the amplifier in the speaker. Oh, the old Bose had them. That's been 25-30 years ago.
🤣🤣🤣🤣🤣
Thank you so much. But I would have loved the diagram of connections as why they are different.👍
you could have shown the wire if the wire did not have any markings on it.
I’m trying to find out if I need a TRS cable from my sound board to my monitors, or a TS cable.
Same😤
PLEASE EXPLAIN WHAT IS A TIFFANY STYLE RCA CONNECTION, MOST AMPS COME WITH TIFFANY STYLE RCAs BUT NO INFO HOW TO CONNECT THEM TO HEAD UNIT. THANK YOU MR. RUSSELL
Great info and well presented.
Thank You Sir. Really helpful!
Nice presentation. You may want to add a correction about the speaker cables NOT working in the instruments. The speaker cable has lower resistance and no shielding. It will deliver the signal to the instrument along with all the other interference that affects small voltage and currents like what is delivered to the instrument. The instrument cable on the other hand (much thinner) has high resistance and may overheat if used with the high currents required in the speaker circuit.
Great explanation with accurate info 👌
awesome explanation, thank you!
I think the XLR midi cables sound the best between my tube/optical compressor and mixing table.
What about you guys?
Incidentally, I've recently used such a cable to hook up a Philips 541 MFB vintage speaker. Sounds fine.
Speaking about a TRS male 1/4 inch connector that goes into a mic interface, what would be the proper size? (16AWG, 18AWG, 20AWG, 22AWG, 26AWG, etc??) Thanks a lot!!!
Awesome video! I learned a lot. Thanks!
This has helped a lot. Thankyou.
Is 1/4 inch also referred to as 6.3 mm? Is that the diameter or circumference of the jack?
Fantastic video. Thanks for sharing your knowledge.
I have an XLR with Jack input that fits my phone. Will it be able to work through my phone?
The question I can't seem to find an answer for is. About balanced and unbalanced connections. If your instrument Output Balanced and you have an interface with unbalanced input or vice versa. Does it work either way?
It should work, but you'll just end up with an "unbalanced" setup.
Red and Black for stereo audio RCA, Yellow is usually Video.
Dude i learned so much from this video. Thanks!
I have a dead speakon is it maintainable or do I have to buy a new end?
Does the the length of the cable effect performance ie if you make up a daisy chain ?
I understand XLR cables are mono. Can I use a 5-pin XLR however as stereo?
Could I then find an TRS-to-5-pin-XLR adapter to make my signal stereo?
please please help me. I have a speaker vintage with a brown rca Jack pretty sure it's called an rca and there is no brown on my receiver. what colour do I plug it into???
I have balance cable problem , I have to go from 4.4 pentaconn dac output to my Mackie HR824 Mk 2 monitors. I have to two choices Xlr3 pin or balanced 1/4 TS Can you make me a pair 7 feet long
Came across a speakon connector on an old power amp and was utterly flumoxed about how to plug it into the 1/4 inputs on the massive speaker setup i need an adapter.
Hello.i have a quick question. Which cables do i need to connect a controller that have an rca output to xlr speakers? Thank you!
How are xlr cables plugged in? And unplugged?
hi Ken, my active sub has a Speakon cable but one end are 2 bares wires red and black....how do these bare wires connect to my AV amp ?....thx
Hi
Could you help me with
( How to repair a cable in which there is a 3.5mm stereo and at the other side there is midi 5 pins )
I am asking about the colour and how to connect 3 cables with 5 cables inside )
Thx
Thank you so much my brother your video helped me a lots
Thank you for this, Kennis. It was really very helpful. That said, I have a question. I decided to check my 1 month & 10 day old "speaker" cables (used to connect my home studio Tannoy monitors to my Mackie mixer), and the 6' Pearstone (TRS to XLR/M) cable says "Professional Microphone Cable" on it. I mentioned the age because it's a week and a half past my 30 day return window :( Is this ok? You mentioned instrument cables are not recommended for speaker connections because they'll get hot, may cause damage, etc.... Should I change the cables? Note, due to a recently rigorous schedule, I have not yet plugged up and tested any of my new cables or the new mixer.
@@kennisrussell Thanks, Kennis! You're amazing for replying on Christmas Eve. Have a great one!
Also can you give your recommendation for the best quality speaker cables? Thanks!
Kennis Russell Thanks for the reply back. Much appreciated.
Whats better connector for low freq(bass). Balance or unbalance?
1/4" connectors were designed to convey signal, not current. They simply don't have the surface area at the point of contact to efficiently transmit power. The fact that they became so common for speaker connections in some market segments (mainly guitar amps but also pro audio) is mildly baffling but I guess it's just one of those things. 🤷♂
11:43 Speakon connectors were specifically designed for moving power loads from amps to speakers. They have much more surface area at the point of contact than 1/4" connectors.
Even XLR makes more surface contact than 1/4" connectors.
There are some 1/4” to RCA cable, for connecting a keyboard output into a RCA input in the market, does that do damage to the instrument or the amp?
I used that type of cable to connect my synthesizer to home stereo aux-input, years ago. Worked fine for that.
i have a guitar processer(Firehawk fx) and it has 2 XLR out and 2 "1/4"out ...do i need these kind of speakon, xlr,1/4 speaker cable to connect my guitar processor with powered speaker?
Thank you sos much....... I was using a guitar cable to hook up my speakers and I did not know that.
thanks! that was so helpful
Why you did not said that audio xlr can be two tipes . ? I mean xlr microphone cable,and xlr speaker cable ? Both is not the same .
....does anyone know if an xlr output connection will also send out power? .....I have a powered subwoofer that has an output xlr connection......I'm wondering if I buy a passive speaker with a speakon input connection and buying an xlr to speakon wire, would it power the passive speaker?
Brilliant. Really helpful video.
Is it ok to convert 1/4 to RCA?
I have a question relating the difference of speaker and instrument cables: i know how the cable itself differs, but is the plug any different? Would it be safe to solder a plug from an instrument cable to a speaker cable? Had to toss one plug from my speaker cable.
Bernhard Löw 100% you can the connector is the same as long as its a mono connector with only 1 ring instead of two.
Videos For fun thanks very much!