9 Things I Wish I'd Known About 3D Printing
ฝัง
- เผยแพร่เมื่อ 28 เม.ย. 2024
- In this video, I share the 9 things I wish I'd known when I got into 3D printing. Brought to you by Sunlu. Check out the S4 Filament Dryer here: jle.vi/sunlu-s4
With so many new people joining the hobby every single day, I got a bit nostalgic recently thinking back on my own journey from beginner to still learning every single day but definitely very proficient...
In this video, I'm going to share with you the top 9 things I wish I'd known when I started with 3D printing. From the basics, to more advanced things I've only recently learned after years in the hobby.
So whether you're just getting started, or you've been in the hobby for a while now, stay tuned, because I have some valuable tips for everybody.
🎁 ENTER TO WIN FROM OVER $5,000 IN PRIZES DURING OUR $100K GIVEAWAY: jle.vi/100k 🎁
💬 JOIN MY DISCORD: jle.vi/tnl-discord
🎥 IN THIS VIDEO: 🎥
00:00 Introduction
01:33 Invest In Your Learning!
04:46 Too Much Is Never Enough
07:30 Working on 3D Printers vs. 3D Printing
09:21 Learn (The Right) CAD Sooner
12:12 Don't Be Afraid To Try Exotic Filaments
13:56 Dry Your Filament!
17:27 Clean Your Build Surface (Properly!)
20:32 Community
23:18 Reconnect w/ What You Love
🔗 LINKS MENTIONED IN THE VIDEO: 🔗
👉 3D Printing Failures: How to Diagnose and Repair ALL Desktop 3D Printing Issues Paperback by Sean Aranda: geni.us/3DPrintingFailures [Amazon]
👉 The Udemy course I took about the basics of 3D printing: jle.vi/3dprintcourse
👉 Prusa Academy: www.prusa3d.com/category/prus...
👉 Ellis 3D Printer Tuning Guide: ellis3dp.com/Print-Tuning-Guide/
👉 Onshape: onshape.pro/nextlayer
👉 My previous video where I shared why I switched to Onshape for most of my modeling needs: • I'm Ditching Blender f...
👉 Playlist of all my different filaments (common, advanced and exotic) and how to use them videos: • Filament
👉 My previous video about the 7 lesser-known and exotic 3D printer filaments you should try: • Level Up Your 3D Print...
👉 My previous essential tools for 3D printing video: • 15+ 3D Printing Tools ...
👉 Check out my podcast where where I interview the leading authorities and influential thinkers in the 3D printing and maker communities: • The Infill™ Podcast
🛒 RECOMMENDED GEAR: 🛒
📍 Complete list of 3D Printing accessories: kit.co/jlevi/3d-printing
📍 Complete list of my videography gear: kit.co/jlevi/content-creation
📍 My favorite 3D printing filament: jle.vi/polymaker
📍 My favorite 3D printer right now: jle.vi/voronkits | jle.vi/bambu (supports 3D Print General, who’s channel was deleted)
📍 My favorite BUDGET 3D printer right now: jle.vi/sovol
📍 Check out the official TNL merch: shop.thenextlayer.com/
📍 PLEASE CONSIDER SUPPORTING THE CHANNEL BY SHOPPING USING MY LINKS! FULL LIST CAN BE FOUND AT: jle.vi/links
❤️ LOVED THIS VIDEO? ❤️
▶️ Subscribe to the channel
▶️ Watch my other videos: / @thenextlayer
🔔 Turn on Notifications
🎁 Support me on Patreon: / thenextlayer
🎁 Send a “Super Thanks” (Tip)
🛒 Use my affiliate links for your 3D printing or videography needs: jle.vi/links
💬 Join My Discord: jle.vi/tnl-discord
✍️ Write a comment below!
👍🏿 Like this video
#3dprinting #3dprinted #3dprinter - วิทยาศาสตร์และเทคโนโลยี
Thanks for watching! If you're not subscribed, you definitely want to be... We're giving away OVER $5,000 worth of 3D Printers and other goodies to celebrate hitting 100K Subs! 🎉🎉🎉 jle.vi/100k
Sunbu Lab AMS Lite 1.0, a S4/AMS Lite fusion 🥳
th-cam.com/users/shorts2Q9C1bFs7RI?si=zDK50QXlhNKuOcMU
3D Printer is a drug... I can't get away.
Yes, the "Why your prints are failing" video would be greatly appreciated for people new to the hobby.
Noted!
Agreed. To go along with the "curated information" part, I wasted almost 200g of silk PLA filament in crumbled prints for my daughter before I found the possible answer buried in a Reddit post. I needed a higher temperature than listed because of the PLA/TPU blend they used (220+ vs 209-212) I'll know this afternoon if it works.
Also, finding out that the difference between what the heated bed is set to vs what the build surface reads can be 5-15 degrees cooler than expected on the plate depending on the surface used.
All sorts of "fun" things to learn. Great video!
@@dwilliam16 update us if it works please
@@binyominmartin3308 Mixed results. Overall better appearance, but still brittle. It's one of those flexible dragons and it prints just fine in normal PLA. I guess I need to run some tuning tests for this brand of silk.
Yes please, I’ve had a pla print recently failing multiple times and changing temps and airflow isn’t helping
I now understand why you speak slowly and clearly unlike a majority of TH-camrs, being a professional speaker was a good past life choice for you!
"People pay for the curation of information, not the information itself" Oh boy that's a nugget right there!
Thanks man! Honored to have you as a viewer!
As a professional educator, I wholeheartedly support this!
with my own money i saved up i bought an ender 3 s1 pro and am loving it. im 12 yrs old and have been printing for 3 months and researching for a year on 3d printing. I'm a hobbyist in 3d printing and want to upgrade my printer a lot. and i want to make a business doing 3d printing
I also transform my hobby into a full-time job and there is no limit to learning new things. TH-cam is a great source of information but sometimes reaching out with experts could shortcut a long journey. I would love to get in touch more often with nice people and share our experiences. Thanks for your videos and I hope we will find peace in Israel. Shalom
Been 3D printing 12 years now. I use a textured PEI sheet and I found what works for me (99.99% of the time anyway) and that is clean with 99% isopropyl alcohol then every 3-5 prints I wipe the bed with 0000 steel wool (super fine) it does not damage the bed at all but does remove those ghost print marks and is as good or better than Dawn washing. Just to test this I have been using this method for around 500+ prints without washing in soap (use to wash in soap every 5-10 prints). I also have my Z offset set dead on (perfect first layer) so for me at least this combination has yielded maybe 1-2 warped prints for 500+ prints and those were when I went too long before the steel wool. Now the steel wool makes no visible marks on the bed (surprised me) and when I use it then IA clean the bed looks brand new. I had heard years ago about using steel wool but figured it would ruin the print bed (sand it down) but I was very wrong and wish I had tried it even sooner.
Thanks Johnathan for another informative video. Rabbit hole indeed…I’m 72 and retired and bought my first 3D printer, AnkerMake M5C, a little over a month ago and now also have a Bambu P1S and printing with ASA & PC.
Great to hear!
Might I suggest you speak your topic titles aloud in future videos rather than leaving them for the viewer to read? I listen to your videos while at work so I don’t have the video playing in front of me. The dead air while waiting for the next topic to start was kind of off putting. Other than that, great information here. Appreciate it.
I agree, I was listening to the video on a drive and was left to infere from what was being talked about to guess what the subject was.
The topic was stated around the 1:30 mark. Are you saying push that to the very beginning?
Edit: sorry the 1:25ish mark. But I see what you're saying. The beginning of each topic within this video, not the topic of the entire video. In that case I agree.
@@ryanback5888 the topics are visually represented but not spoken. So when you’re not watching the video but just listening to it you miss out on what each topic/subject is and it’s just dead air then you have to figure it out on your own what he’s talking about.
The point about CAD is well made. I'm a teacher, and when I saw a handmade 3D topographical map that someone had made as a hobby I realised how great it would be to have resources like that for my classroom. But the person who made the one I saw spent months on it! I don't have that sort of time, but I wondered if I could 3D print them. I went to an open day at my local 3D printing club and explained what I wanted to do. "Oh yeah, that would be easy" they assured me. Yeah, right. Easy for them perhaps, but I didn't know CAD. I investigated so many CAD programs only to find out after wasting a lot of time on each one that they aren't what I was looking for. For example, I was making progress learning blender, but then discovered that it's built in font doesn't handle text macrons, which I needed for adding labels in the Māori language of New Zealand. After wasting a year I gave up. 😢 I keep watching your videos though, because I hope that one day I'll hear of a way to make it work and be able to try again.
This was a fantastic video! Very well presented and I honestly agree with all of your advice. I would love to see the “why your print is failing” video.
I’ve found that I definitely fall more in the “making your printer work” side of the hobby. The tinkering is the fun bit for me. Nothing beats designing my own models to solve my own problems and then printing them on my own customized printers!
I love your videos and positive energy. I am a new 3D printing enthusiast. With a background in engineering and then later on as an application specialist for Silicon Graphics on Alias|Wavefront products (Maya) I am no novice to 3D applications. I have picked up Unshape on your recommendation and already find myself doing fun projets. What really make me thrilled is the ability to see my models and designs some to live. Investing in a Prusa MK4 has given me a reliable output device while maintaining a touch of the Open Source. I will be doing a little of everything from tinkering/upgrading the printer, printing useful tools for my workshop to hopefully one day building a prototype for my own milling machine. Thanks again for your great content.
not only is this guy super informative, relatable, and knowledgeable… he's also quite a looker 😏
There is no destination, only a journey. When you finish a project, you always seek greater and grander things. You should not quit when things don't go your way. It's not a race, it's a marathon.
I just got into this hobby a few weeks ago by purchasing a Bambu P1S. I really do enjoy your content. I feel I've learned so much and avoided so many of the initial pitfalls I see other new enthusiasts talk about in other chat groups.
Keep up the great stuff!
definitely will be nice to see about social media 3d printing
The s4 is amazing. I’ve been using it for a couple weeks now for my TPU and it has made a massive difference in the quality of the prints
Reporting in from the deserts of Arizona: we also need to dry our filamnent. I thought my printer was broken until I opened a new spool and it printed perfectly fine. Got a filament dryer and now all is well.
The one thing I wish I had know is that there is ALWAYS another filament I need to try out "just to see". 80+ spools later and hey look...I just found this new filament. I think I'll give it a shot.
Yuuuuppppp
When I was collecting bits to build my Voron V0.2, I was talking to a friend about buying my 3d-printed parts from PIF. He suggested that I instead strip down and rebuild a bedslinger to do it. It was a GREAT suggestion, I learned a ton from that project, which greatly informed my Voron build. Part of the learning was that since I started with a random $50 garage-sale find, I was pretty comfortable ripping it apart and rebuilding everything. In the end, I found that the $50 garage-sale bedslinger printed better than the originally-better-but-unmodified bedslinger I had been afraid to experiment on.
Point number 9 hits home. I haven’t printed anything since last november. Need to pick up mastering onshape and design and print that handle for the waste bin. My partner has been bugging me for some time now😂
איזה אח, צפיתי בכל הסרטון לא קלטתי שאתה ישראלי עד הדגל ישראל באמצע, תמשיך להציג אותנו לעולם אח יקר
I started 3D printing back in January 2023 with a $100 Ender 3 Pro from Microcenter. Got my second printer (a used Anycubic Kobra Plus which turned out to be a huge headache) and a bunch of Ender 3 upgrades in January 2024. Last week I ordered a Bambu Labs P1S so i can focus more on just designing and printing, while also having my tinker printers.
Now, we're getting a P1S at work too so part of my job now will be designing and prototyping custom hardware.
I never expected myself to go past just printing free models, but this has turned into so much more.
I'm a long time professional Blender user for work in visual effects and motion graphics. I'm new to 3D printing and while Blender has stolen my heart long ago, you are much better suited learning an actual CAD application of which Blender is not.
(Edit) The one area where Blender will excel is sculpting. It's similar to Z Brush but easier to manage.
Your videos are fantastic. Before I got my Neptune 4 pro, I saw one of your videos where you talked about leaning the build plate with Dawn dish soap. Every time I start having adhesion issues, that solves my problem every time. Thanks for your content
Awesome, thank you!
My favourite quote. "If you just want to print things out, maybe DONT get an ENDER machine."
Ive being TRYING to say this in my faebook group for months! HAHA
Truth
@@thenextlayer Have you tested the Ender 3 V3 KE or the V3 SE ? The Ender 3 improved a lot with the current generation.
I've been messing with Freecad and designing little things.
I made a custom shelf for the top of my TV, with a separate little piece to connect the sections so my cats don't pull them off.
Also designed a table for the arm of my chair with a mount for a USB keypad
Very well written. It's amazing to see how far you've come in your delivery of content. I always look forward to your next video. Keep up the great work.
Fantastic overview.
I just dove in, bought a Creality K1 Max, and was immediately overwhelmed.
I value your advice very highly. Thank you for your dedication to the hobby, and passing on your knowledge. I too, would like to see a "Why your prints fail" video. Take this with a grain of salt as I'm in no position to give advice. I think it would be helpful to the less technically savvy to really drive home what z-offset is and what it isn't. I've seen so many Social Media posts asking "Why is this print failing" and most of the responses are (sometimes absolutely wrong) "Adjust your z-offset." To which they reply, "What is z-offset?" Or, "What do I set it to?" Or, worse, someone replies "Set your z-offset to -1.32, that's what mine is." I'm not sure why it's such a hard concept to grasp, but I think it merits a deeper dive.
Love this video! I spend months setting up kitchens in restaurants and learning the best and most efficient methods so that i can train the other staff to learn as fast as possible with consistent results. This format feels like what i do for other people only this time i need training! I consider myself a good learner but sometimes i do too much at once and this gave me direction
Thank you for continuing to produce such helpful content!
My pleasure! Thanks for continuing to watch it!
I would watch the social media video related to 3D printing. That would be extremely beneficial for myself and everyone else that is new.
Really appreciate this video. I've watched your stuff off an on but you got my sub today. Im like you been doing this for years and always learning new things. Never came across that CAD program before so I'm going to check it out. Thanks for sharing this! 👍
This video literally dropped at the perfect time. I had just been introduced to your channel recently actually and just happened to stumble across a new video from you. Rescrubbing my build surface with soap has finally allowed me to complete a print using ASA filament that I have been struggling to get stuck to the bed. After scrubbing, the print stuck flawlessly without ANY warping. I'm very pleased with the results now and will certainly will be moving forward with this method of cleaning.
I really wish this info was more prevalent... even the instructions that came with my PEI build surface only say to clean the plate thoroughly with soap before the first use, after that they say to use isopropyl alcohol for routine cleanings. Makes perfect sense though, dish soap has very powerful surfactants that are the best at grabbing and removing grease/oil. Only thing I would add to the info you gave is that a good way of telling if you have scrubbed good enough is to watch the rinse water running off the plate. The plate will become hydrophobic allowing the water to sheet off.
Great video, I'm definitely a subscriber now. Thanks for the effort you put into your channel, it really shows.
Happy to help!
I'm so used to watching ancient 3D printing videos that I didn't realize how fresh this one was 👀
Also, since I don't seem to be going anywhere anytime soon, I guess I'll hit that subscribe button and see what it does 🤔
Noice!
SMRRF was such an experience. Such an open and accessible community.
Sean Aranda's book was so helpful. I keep an extra copy at home, just to loan or give to someone who is trying to get started with a new printer.
Great Video! Thanks.
I would like to find out if you would recommend the bambu lab p1p above the creality k1? I have a ender 3, and have been getting consistent prints on the machine.
Was just wondering why you are so biased against the creality printers.
I just got one because of availability in my country.
Regards
Definitely. Had a bad experience with the creality
My first printer was a QIDI X-Plus and still loving it to this day using FreeCAD.
Very educational video. Can you tell me what 3d scanner is best if I want to 3d a full body of people figurines?
Not sure sorry. There are better ones for bigger objects but I haven’t tried
The side of the hobby you gravitate to is the first thing I ask people to figure out 😅. I'm really into my printers. Either I'm working on them or working using them. Hate printing trinkets just to check filament 😂
Wow Zach, good content there! And you've affirmed that I'm heading in the right direction. I've always been a constant learner, always up for a challenge. It's only been about two weeks since deciding that I NEED a 3D printer. I've been learning OnShape and have created a replacement bird feeder lid while having a blast while doing it. I'm a retired 70 year old woman, and can never seem to get enough knowledge. I'm having as much fun learning OnShape as I will printing. I don't have a printer yet because I want to learn much more before doing that, but I do know which one I'm getting. Thank you again for making this old gal happy and encouraged! Subbed!
I started with an Ender-3 S1 only to realize the reward of successful, cool prints wasn’t enough for the effort of bed-leveling (despite auto-bed-leveling) and subsequent z-offset needed after nearly every print. I now have my daily driver of the Bambu A1 and the Ender is now my project machine with a few upgrades installed and a few queued up for future upgrades.
i am just starting to get into 3d printing havent gotten the printer yet but been watching videos and yours keep coming up and i have to say i like your videos and yes i subscribed to ya. and onshape looks like it might suit me well learning about it currently but it seems very easy to use thanks for the video
Please do a video on filament tuning in different slicers and why this is important and the profiles with in different slicers are not an all fit solution. I’m struggling with this right now.
Got a roll of Polycarbonate - great material, just have to be wary of warping. Might have to patch up cheap enclosure for better heat retention, maybe find a way to heat it up better, or maybe just get a better enclosure. But for some things it's fantastic, especially if you want something that can hold up to a lot of heat.
i learned to 3d model first and the wanted to have a printer to print out my creations. and ever since i just keep going. learning modeling trying to improve learn new skills to create the things that bring me joy:)
A video covering your favorite community sites (discord, reddit, etc.) Would be awesome.
Can you recommend the right designing app/software for making cookies cutter or miniature clay cutters?
I love onshape
Hey Jonathan, OK, well I think I really need to call out just one thing.. :) I have to disagree with your just wash the build plate first and every time advise, but please hear me out first... :)
My recommendation would always be the following for bed adhesion issue, first double check t hat your build plate temp is within the range specified by your filaments manufacturer, being too cold is common reason many prints will not stick, this usually happens after people will try to recover to correct a warping or elephants foot issue by dropping their temps. If this is the case, there are a number of videos out there on how best to correct those situations without lowering your plate temps too low, giving your build plate a really good washing with a name brand dish soap like Dawn Powerwash or similar is great advise, just make sure it has no hand conditioners or lotions just as you stated has stated, in the video in most cases this will in fact work with the exception of a situation like mine where nothing ever sticks to my build plate after I wash with with the dish soap, though this is likely something specific to my environment though I don't know what it could be, If you still have issues, do wipe it down with between 70% - 99% Isopropanol. This is the part where we do differ from as I do believe it is better to wipe down with the isopropanol in between washes to ensure that your prints will continue to adhere to your build plate. I don't know why you are tossing this out after all this time, as it is a cheaper alternative to constant washing ever X prints. Washing your build plate after every lets say 10 prints or so could get costly for some people as for example Dawn Powerwash can cost u p to $7-$9USD unless you buy in bulk and if your on a budget this could get a bit expensive compared to the cost of a bottle of isopropanol which costs around $0.79- $0.99 per bottle and one bottle can last you a VERY long time, in fact, it usually takes me months to go though one bottle with an average of 2 long prints every few days. This also saves time, as well people do not realize how much removing the plate each time and placing it back on the bed each time can cause your bed to need re-tramming. Admittedly wiping the bed down aggressively can have the same problem which is why I don't recommend aggressively wiping the plate down either, a gentle wipe down should be all you need. Also if you find this to be the case where you are having to continually re-tram your bed, I suggest replacing your springs with silicone bushings instead, however, there are some debates as to why bushings should never be used and why springs should never be swapped to bushings though, I have never found this to be the case, in every test I have run, bushings have proven to me to be far superior in every way, though I digress. Your bed will get residues on them from the filaments, as well your grubby little fingers will leave oils on the plate every time you touch it. After time, these smuggies will eventually lead to a complete lack of adhesion and a simple wipe down saves you on both time and money and if your not too aggressive, you won't risk having to continually re-tram your build plate. I honestly don't understand why you are dismissing the isopropanol after all this time, as it would seem to me that the isopropanol would be the perfect solution to fix a simple adhesion problem and to do so proactively in between having to take the plate off and give it a good washing. Of course if you're using glue sticks or any number of other bed adhesion products to get your prints to stick, the washing the plate is really your only option as isopropanol will just make a giant mess of your build plate, but I truly stand behind the use of isopropanol in between washes are a quick an easy, lets call it a maintenance step between washes or if you run into a problem early of and your prints start to have adhesion issues as a quick wipe down will get your print restarted right away and may just solve the problem until you feel a wash necessary. I would be interested to hear a bit more as to why you have decided to turn your back on the tried and true isopropanol as you even stated that this has served you well in the past. I bet I know why!!! Has Dawn sponsored one of your videos??? Gosh, I am so jealous of your makers / creators, you guys get all the good stuff free! LOL I am sorry that was a low blow, I sincerely hope you did not take offense to my very off color humor, I meant this completely as a joke! I know, my humor is rather tasteless and poor, hence why I never went into standup!
I would highly suggest you do not lather your build plate with a glue stick unless you are use a standard and worn build plate that has become troublesome for you to get good adherence, or your are printing with a filament like PETG. If this is where you find yourself, I would highly suggest if you have the means top upgrade your build plate to something like a smooth PEI sheet. These sheets are known for their adhesion and most standard filaments should have no problem adhering too them. PETG is definitely the exception as you are using the glue stick not for its adhering properties but as a releasing agent as PETG becomes extremely sticky and an unprotected glass bed is likely to be torn apart by PETG, I have never seen anything like it, it will literally destroy your glass plate! The Glue stick is good when you have a specific filament which is known to have adherence issues such as the exotic filaments but should never be your first choice for gaining adherence for filaments such as the standard PLA. PLA should not have any problems adhering to a clean and not worn build plate. I
Lastly just a quick note why I am very much against the many creators advise to slather on the glue stick, hair spray, or any number of adhesion products available to make sure you part with your hard earned money and that is that these products tend to not only stick to your build plate, and in most cases will keep your print firmly attached to your plate, but when you r print has completed, and you remove your plate, you are likely to notice that much of that product is likely also adhered to the bottom of your print as well. In most cases you should be able to wash your print to get it off, but in some cases I have found that that when the initial layer was being laid down, and the filament at it's hottest, some of the glue or other products have been absorbed into the hot filament, which at that point, you will have little chance of being able to separate it from your print leaving a nasty white residue permanently on your print. This is terrible if this happens to be an outside / visible portion of your print and this is exactly why I have to disagree with any maker that provides this as their first line in trying ensure your print adheres to your build plate.
In closing, Jonathan, I would really like to understand why you are disavowing now the isopropanol as it clearly works, your history with it proves that, but were you simply trying to say not to just only use the isopropanol, ie never wash washing the board, or are you more or less boycotting the use of isopropanol all together? I guess this is where I may be missing your point here.
Oh more lastly, reading some of the other comments made me remember the one really important thing that I wanted to share with you. You are a fantastic communicator, the way you present your video's comes with a bit of authority/ confidence, but not condescending, as that is extremely important when your hosting your videos. There is another very young creator / maker, that has a large 3D Printing channel who's videos tend to be quite informative, but I honestly can't take more then a minute or two of his videos, as he comes across very condescending as if he is the gift to the 3D Printing world which I find extremely odd in this maker space. Most of us in 3D printing tend to be introverts, and no matter how long one has been in this space, we can all learn something new from the most advances users, to the new commers, but his videos tend to have this air of him being the best, so don't bother suggesting something since he already has a better answer. It's a real turn off as some of his videos I actually want to watch but I can't. Your videos drew me in when I first found your channel as you almost seem like the best friend I never had! That is an amazing skill and a good reason for why your channel has become so successful! Don't ever change your honest persona! It's just an amazing talent, though I believe it's less talent and more you just being you! :) Amazing work as always Jonathan!
Many thanks for this excellent video and for your future reply to this!
Cheers,
John
dude these videos are getting so much more polished every time! i've been watching since ~Nov 2022 :)
I’m going to steal, “Still learning every day but definitely proficient.” 😂
Yup - got into 3D printing back in August 2023, and if I had the space I would already have supplemented with another like Bambu’s A1 / A1 Mini… Having 40-50 filament rolls, including the holiday sale purchase…. Well when I see new exciting colors, dual or triple color silk etc…. I want more. :O Also just started trying out PETG (was PLA variants only before), and following your “script” I have actually just started to dive into CAD designing. :D Watched so much videos about TinkerCAD, and did a couple of own needs / designs in TinkerCAD, but already looking into Fusion 360….. Never had a hobby that expanded so fast before….. :O Btw agree with the dish soap cleaning! Did not have any issues, except when I thought I could ease up on the cleaning of the build plate…. Proper cleaning again, and no issues with models not sticking to the build plate since. And last but not least I also have the Sunlu S4, and well the S2 as I started out with that. So in my short 3D printing life, I can already confirm much of what you stated in your video, in relation to myself / my experience so far.
What printer would you recommend?I want to starting doing 3d printing.Thanks
I'd recommend adding the voicelines when you title a chapter in a video. Because there might be audio listeners (like me when i'm at work) who can't watch and read what's on screen at all times. Great video I loved this one alot :)
hey man, love your videos. IDK if it's just my opinion but I'd really like to see a video about your personal projects, whether it's just the Gridfinity kitchen organizer thing or a fully fletched project with electronics and real functionality.
My 3D modelling needs aren't that complex. TinkerCAD is all I need. Most of the things I model myself are simple things, like replacements for simple parts that I have either lost or broken, or something to fix a small issue. The most complex thing I have modelled so far? Replacement sun visor clips for my car.
I've put off getting a#D printer for a wile because i could still make the things I wanted with other materials and I know that can be a lot of frustration with print failures and tweaking the machines. It's finally hit the point where Bambu is pushing for print consitancy with more monitors a. alower price bracket that it's worth getting plastic production for me.
Up to this point most cosplayers where saying get ANY 3D printer because you going to have to spacale and sand then thing like crazy to remove print line.... what I'M excited for is printing files on the smallest nozzle and finest detail setting to reduce print line in pretty filaments that will be Cosplay ready. And for ones that will be paint the less spahle and standing the better!
Am I going to print custom upgrade, VERY likely but I'm not interested in tinckering with machine hardware outside of replacement part.
Do a video on flexible filaments! They're super under represented
The more filament part is 100% true!!! Do I have enough spools to last my one printer 3 years? Yes. Do I want more? OF COURSE!!!
Amazing vid as always dude!
Hi I’m completely new to wanting to learn this I really want to do interior design like wall mounts and furniture overlays. Can you direct me where I can find content on this? Haven’t bought a printer yet and not sure the best for this type of product. Thank you!
My own lesson learned. I think the biggest thing I learned after diving deeply into 3D printing is that 3D printing in and of itself is NOT a hobby. 3D printing is simply a tool. A very intriguing tool that can allow you to do things you just can’t do any other way, but a tool just the same, like your drill press or your lathe. It is an amazing tool to support your ACTUAL hobbies. How much use you will get out of it is entirely dependent on your lifestyle. Do you have a craft space or a workshop or garage? Are you always building, tinkering, repairing, improving, rebuilding, creating things around the house? If so, then a 3D printer can be an incredible addition. You may wonder how you did without it. But if your lifestyle doesn’t already include these kinds of activities and hobbies, or doesn’t really have the physical space for them, you will struggle to find applications for your printer. I mean seriously, how many Mandalorian figurines does anyone need? I am still enchanted by the possibilities, especially the design process, but learn from my experience and give this all some serious thought before you leap.
Hello , i love your video ( google pop it randomly while looking for random things) consider me subscribed. Thanks for this as im going from zero to the world of 3d printing. Wish you the best from Mexico.
Thanks for subbing Amigo
Quality video, liked & subscribed👍
I love the energy you have about printing. I appreciate the reminder to take a breather and print something for fun or the latest cheesy model.
I’ll do that as soon as I get my HeatBlock unclogged and extruding again… wish me luck Lol :/
It was a really fantastic video that I was seeking in youtube for today. Thanks from your friend in Iran.😘
Thanks Junam!
I see progress on subscribers number at this moment 90k, good progress and congrats. Also more video materials that we have miss for some time when we have been feed by podcast materials. good to have you back in good shape. as always best whishes and all good for you and your family.
Looks like i need to buy the s4. It’s a lot cheaper than expected. I did get a single filament dryer from sunlu not long ago. Definitely helps out.
Great video.
You’ll love it
I’d love to know where I can go to ask a question about actual bed leveling not software leveling. I can’t use the backside of my bed on a non adjustable bed. I’ve lost 50mm 😢. Love the videos tho! 😊
אתה יוצר תוכן אם כישרון רב :)
מכווה להצליח ברמה שאתה מצליח אך בתחומים שונים :)
הסירטונים שאתה מראה הם באיכות טובה-מאוד ואני מיתמלא בגאווה ושימחה בכול סירטון :)
המשך להצליח ואנו איתך :)
תודה עבור השיתוף :)
(: THANK YOU FROM ISRAEL
Best description of the hobby I've ever heard. Just described the last 10 years!
Would definitely appreciate the video on community resources - particularly for Discord, which I always struggle to get into.
i am buying my first printer Ender 3 v3 kE and since I am an engineer and an interior designer; I am familiar with CAD software like AutoCAD and Sketchup. I am a professional learner to so I want to learn Fusion 360 soon. and the one you mentioned (Onshape) I will give it a try.
I think I'm somewhere between, I want to print useful things and I want to learn about the 3D printers themselves.
I'm always willing to learn something new and I hate it when people don't want to learn anything new but want everything to just work for them. I have to deal with people like that way too often in my job and fix what they've broken.
I love 3D printing so much that I got myself a bambu lab p1s for my bday to help with my fiancee's markets! Also signed up for a few neat patreons!
No talk about wood or brass PLA? I’ve only been printing for a few months but those are my favorites so far, I like the finish they provide and also that they are sandable. Also Silk PLA especially in gold. This comment is really more appropriate for your prior video but I’m making it on this one because I’m lazy haha.
I love your content. I actually have a specific issue I'm having right now and I've tried researching but I'm still confused on it. My prints come out almost spongy, and delaminated lately. I'm using Sunloo PLA+. Not sure if you've ever had this issue but would love some insight of possible
Sunlu not sunloo
Sounds like you need to dry your filament.
Proper dish soap + drying -> Bare glass sticks like mad.
Funny thing; Once you print on it enough, it becomes resistant to oils etc. as a really tiny surface of plastic sticks to it.
Can you do a video all about bed adhesion?
Finally something good on my fyp. Great video with great tips and info, looking forward to watch more of your videos!
/ /fellow maker
Welcome aboard!
Nicely done! About soap. I would encourage folks to use a detergent that has no additives. Dish soaps like regular Palmolive May have skin conditioners and fragrances that might leave a residue. There is a “Palmolive Ultra Pure + Clear” product in a fragrance free version. Industrial detergent might be better, though costly. Sodium carbonate (not bicarbonate), AKA washing soda, should also do a good job, with no residue, though tough on hands.
Oh snap didn’t know that!!
Really enjoy your vids
I'm a noob. Hope you can help me. I need to know if I should leave my PLA filament loaded in the head, or should I remove the filament when I am finished 3d printing an object. Is it safe to finish printing and just leave the printer loaded with the filament. thank you for your help. BTW, what modeling program can a non-engineering type like me use that doesn't require years of training to use. Tony 😎
Try Cura it is one of the best slicers and it’s ok to leave the filament in the printer it doesn’t hurt anything
I was hoping to dive more into the hobby but having twin toddlers and a full-time job with my partner being a full-time mom prevents me so. I even was able to "aquire" an A1 Combo that could have complimented my P1S but sadly I have to give it up as I have no space and I even haven't fired up my P1S recently because I'm too busy. I wish I can sell stuff to to make spending money on the side but even that I don't know where to start.
Very good video, about this new hobby 3D conception, modeling and printing. Then some just enjoy the results.
To feed the algorith.
TH-cam recently deleted Shawn’s channel (3D Print General) over a bunch of bs. Very unfortunate, considering he contributes a lot to the community.
I feel you about the filament addiction. There are so many different kind... I always look out for discounts so i have way too many different brands... and trying to fit 50+ spools into an office less than 9m square which is also my workshop is hard. And with ADHD I need to have them all on display or I forget what I have. 😅
One of my friends has a spreadsheet for her huge collection of spools. She tracks what is opened or not and also the remaining weight on each spool.
Hey, thank you for your Chanel. I'm often blown away with the quality of videos you make especially considering the age of your channel and the fact that you're 1st video was better than 90% of 3d print videos on TH-cam. I do have one small piece of constructive criticism. I often "watch" videos while doing chores which obviously leads to not seeing every part of the video. When you have your points or chapters introduced, not saying what it is and only relying on the visual description makes it difficult. I would either have to wait and figure out what the point was or find where I set my phone down at and rewind it. I think keeping the visual and having the pause is great, but adding you saying what it is after it comes on screen would be helpful and I'm sure I'm not the only one that multi tasks and would appreciate it too!
I can try to do that going forward!
@thenextlayer You don't have to do anything special just for me, just a suggestion from a random viewer 😊 Thank you for your content!
"or sticks too well" *shows creality glass*
yup, the bane of my existence right now. it's either bonded like cement, or it pops off half way through the print.
elmers works ok, geetech jt 16works perfect for the print itself. but it's still a pain to breack free if there's notable surface area on the initial layer.
fwiw ambient is 72f with a constant, faint hvac draft.
Everybody is different. I only got a rinter for a specific project after cnc milling and CAD.
Hey Johnathan, great video and sent it to my friend who just got into 3D printing and bought a Bambu A1 based on my recommendation since I know he doesn't have much time or interest with 2 kids for working on his printer instead of just printing.
One piece of constructive criticism I have is please read out your section titles. The pause in the audio is a bit jarring and I often watch videos while I'm doing dishes so I get lost if I look away during a transition to another topic.
Thanks, Jonathan!
Best advice I have to new makers. Don’t fall for the overpriced upgrades.
If it prints and doesn’t have issues, don’t mess with it.
Don’t fall for Bondtech, Slice Engineering, etc.
Hardened nozzles, you need.
PEI build plates, good upgrade.
All metal hotend, only if your printer needs it and can support the heat.
Don’t fork over enough money to buy an aftermarket upgrade you don’t need when you could have bought a better printer to start with.
Yes could love a why your prints are failing video.
I need to find my group that's for sure mechanic here started out doing bodywork then transfered to diesel mechanic and now I'm a generator mechanic love the outdoors and vehicles but have a nerdy side like streaming and gameing a video to help find my place in this 3d world would be awsome
Episode: which community is best for learning & helping. Would be great!
I started with SketchUp, now I'm stuck starting simple projects super quick and easy. But it almost always snowballs into Fusion 360 constantly making me rebuild the model 😵💫
My point, SketchUp is VERY easy to learn and you can be designing and printing parts in hours if not MINUTES if you have the inclination for it. Took me 30 minutes to learn and design a phone stand the very first time i used it. But, be warned that if you ever do outgrow it, it will always seem to pull you back and either save you a few minutes or waste hours fixing models because you think you don't want to rebuild the model the right way in a proper engineering software suite while you get stuck in a loop of.. WELL it's just this little mod, not worth it.. just this little mod, not worth it.. just this little mod, not worth it..
Anyone have a recommendation of a printer for a 7 year old that he can start with and grow with?
At times, he can have a short attention span but I think would be able to focus on this hobby. I just can’t think of a printer for him. I only have personal experience with my Ender 3 Max and Ender 3 Pro and I wouldn’t recommend either of them to his mom for her son.
Bambu Lab a1 mini!
One of the first rules when you have a cheaper Printer: Have two Printers avaible. One will always break down and you need Spares... printed. It doesn't matter if the second Printer is someone else for a short emergency Print or even on a Hardwarestore. But you need a second Printer to print. A Cheap old wornout Ender 3 is a horrible printer, but it is the best Printer in the World when you somehow broke a Part of your Fancy Voron and you need a PLA Spare Part for your Voron that you can print an ABS Part on your Voron for replacement propper. Been there with my first printer when i cable tied everything together for one print after the Autolevel holder Broke or the Frame Connector.. since then i have always two working printers so i can five the broken down. Yes a Bambu won't break down.. except the AMS in V1 and V2... then you need a replacement part... Suddenly the old Ender 3 which was decomissioned 2 years ago is the best printer in the world. So fix old printers before you decomission them when it's not expensive and putt them away.
Great video. I think it was about time that someone did a video like this. Shabbat Shalom