Hi, I have a question about Electric grounding conductor EGC. Is it necessary to connect the inverters with 6AWG? If I only attach the microinverter to the rack is sufficient for EGC ?
I'm nm and I got my electricity turned off after my micro inverter started producing me a -370kwh. I need someone that can help me get my system approved. Do you know anyone here in New Mexico, that will help me?
The worst decision I *ever* made was to install APSystem equipment. It is unreliable in that it has a very high failure rate. Worse, they have zero support, and will not honor their warranty even when they previously confirmed that the warranty was in effect. I CAUTION ANYONE ABOUT THESE SYSTEMS! Do you homework. Check out Enphase. Research their failure rates, support, etc. BUY FROM THE ONE YOU TRUST.
Hello guys!, how can I connect the branch circuits for a three-phase system 120 v/ 208 v? The sample wiring diagram in the installation manual is confusing when connected to the distribution panel. I am confused in the connection of the circuit breakers.
Hi Fabricio, thanks for your question. Using the YC500 in a 120/208 environment is acceptable; however one must balance the phases, meaning L1 and L2 land on phase A and B, while the next set of inverters L1 and L2 land on phase C and A, and the next set of inverters L1 and L2 land on phase B and C. Let us know if you have any other questions. You can contact us directly at support.usa@APsystems.com.
Hi, once ECU is installed using a network cable (which is recommended), should I leave disabled the wifi option? Currently I have one installation where we tried all possible conections and in different outlets, but still communication is poor. So, I remember we left the wifi option enabled although it is connected by network cable. Could that perhaps be the problem?
Thank you for contacting APsystems. Once you connect the CAT5 cable, it overrides the Wi-Fi. Some things to look out for, if trying to use the ECU in the kitchen or basement or other areas with noisy products on the lines, communicating with the inverters will diminish. If it is the internet your having trouble with, ensure the I.P. does not end in .228 or start with 10. We are here to help, so feel free to call in if the problem persist, our number is 844-666-7035
Hi there, we'd like to find out more about what's going on with your site. Please contact our support team so we can assist with settings and other setup procedures while on the call. The WiFi function does not interfere with the Powerline Communication (PLC) so there is likely something else going on. Please call 844-666-7035 and we can help troubleshoot the site.
Hi Mark, we’re sorry to hear about your experience. While we do not currently have someone located in the UK, we are continually expanding and constantly looking to improve our service and support. Our support center for the EU and UK is located in Lyon, France and every member of our team speaks English. Please give us a call or email at support.emea@apsystems.com so we can help you with any issues you may be experiencing. We take your feedback very seriously so please reach out to us so we can understand how to better support your needs. Sincerely, APsystems
Congratulations, the APsystems microinverters are the best!
Excellent instructional video. Clear, concise and professional.
14:50 Great Pro Tip; 15:44 Also great tip
Hi, I have a question about Electric grounding conductor EGC.
Is it necessary to connect the inverters with 6AWG? If I only attach the microinverter to the rack is sufficient for EGC ?
I'm nm and I got my electricity turned off after my micro inverter started producing me a -370kwh. I need someone that can help me get my system approved. Do you know anyone here in New Mexico, that will help me?
Why didn't you use a bus cable installation? This type of arrange that you show could collapse the entire system if the first micro inverter fail.
I m.looking for job certified in solar panel installation
Erro de comunicação o q pode ser
The worst decision I *ever* made was to install APSystem equipment. It is unreliable in that it has a very high failure rate. Worse, they have zero support, and will not honor their warranty even when they previously confirmed that the warranty was in effect.
I CAUTION ANYONE ABOUT THESE SYSTEMS! Do you homework. Check out Enphase. Research their failure rates, support, etc. BUY FROM THE ONE YOU TRUST.
Hello guys!, how can I connect the branch circuits for a three-phase system 120 v/ 208 v? The sample wiring diagram in the installation manual is confusing when connected to the distribution panel. I am confused in the connection of the circuit breakers.
Hi Fabricio, thanks for your question. Using the YC500 in a 120/208 environment is acceptable; however one must balance the phases, meaning L1 and L2 land on phase A and B, while the next set of inverters L1 and L2 land on phase C and A, and the next set of inverters L1 and L2 land on phase B and C. Let us know if you have any other questions. You can contact us directly at support.usa@APsystems.com.
@@APsystemsSolarI can get this video in Spanish.
Hi, we need a instructive video using Vitron and APsytems as OFF-Grid, Micro-Grid and Grid-Tied AC. Please.
It’s work in Canada where can buy stuff for solar
Dear, good afternoon. How are you? I am a Solar integrator and I would have to resell Microinverters, How to be a representative?
Hi, once ECU is installed using a network cable (which is recommended), should I leave disabled the wifi option? Currently I have one installation where we tried all possible conections and in different outlets, but still communication is poor. So, I remember we left the wifi option enabled although it is connected by network cable. Could that perhaps be the problem?
Thank you for contacting APsystems. Once you connect the CAT5 cable, it overrides the Wi-Fi. Some things to look out for, if trying to use the ECU in the kitchen or basement or other areas with noisy products on the lines, communicating with the inverters will diminish. If it is the internet your having trouble with, ensure the I.P. does not end in .228 or start with 10. We are here to help, so feel free to call in if the problem persist, our number is 844-666-7035
Thank you for your prompt reply we appreciate that.
Hi there, we'd like to find out more about what's going on with your site. Please contact our support team so we can assist with settings and other setup procedures while on the call. The WiFi function does not interfere with the Powerline Communication (PLC) so there is likely something else going on. Please call 844-666-7035 and we can help troubleshoot the site.
Dear, good afternoon. How are you?
yes they are cool
but we we can not use zip ties here...
Who puts ads on a corporate video?! Literally an ad for your competitor played... so dumb
Vietnam.
too long, too slow, too many musical transitions
They are the worst dont buy. No back up in UK.
Hi Mark, we’re sorry to hear about your experience. While we do not currently have someone located in the UK, we are continually expanding and constantly looking to improve our service and support. Our support center for the EU and UK is located in Lyon, France and every member of our team speaks English. Please give us a call or email at support.emea@apsystems.com so we can help you with any issues you may be experiencing.
We take your feedback very seriously so please reach out to us so we can understand how to better support your needs.
Sincerely, APsystems
I think enphace still better then this I'm a installer