This one is built by Jim Shultz. His email is in the description. Also see more at. www.outboardjetrockejector.com/product-page/the-kit facebook.com/pages/category/Sports---Recreation/Outboard-Jet-Rock-Ejector-3021804454498564/
What is the total weight of your new Kaz 1652, gas ,battery, gear and you.. How much water will the boat draft on a drift. How skinny can you run under power ? Why did you choose a 1652 vs a 1656. Thank's
As it sits in the water full on gas(13 gallons) and me in it will be roughly 1200 pounds (I'm 210). I have yet to measure the draft. As far as shallow goes this video here probably showes that. Probably need 3 or more inches to stay under power. With a 52 inch hull you can stay one piece hull vs a 3 piece.
Thx for ur video s I learned a lot I am doing a 14x48with a 25 jet And the next one will b a 1655low big river with a long tiller 40 hp jet b safe and have fun
Good explanation Dennis. So many people seem to want to set thier trim and forget it.. Im constantly trimming up or down as I speed up or slow down. I also trim down just slightly to get a little better bite setting up for a tight turn, and slow down slightly so I can use the throttle to power thru the turn. If ur wide open and u cant make the turn thats it. If u have a little throttle left u can give her some gas and use the thrust to help turn.
It seems like a jack plate to bring the whole thing up 2~3" would really get the outboard up out the way. With a guy in the rear plus gear weight I would assume you could raise at least 2" and the water intake still be adequately submerged - am I wrong?
Just don’t use the motor at all..I don’t even put a motor on my boat and can glide across the rocks without having to worry about a stupid motor to break. A haha a haha ha.
I think it’s dependent on the speed you’re traveling…..that’s why adjustments are needed on the fly. The water definitely rises, how much is variable depending on speed of the vessel. Hth
@@DennisBohannan i have a 60/40 on a 1652 and was getting about 27-28mph with 2 guys then i added an anchor winch to the front and now im getting 20mph with 1 person should i lower the motor on the jackplate so the shoe is farther in the water? Cant seem to figure out why the boats running way slower besides weight slowing it down in the front
@evanwoyke interesting. I'm not sure without seeing or riding in the boat. Sounds like the added weigh caused a bunch of drag. What type of hull do you have?
I was thinking of this jet boat engine? I am on A Lake with a lot of weeds hyesan Lily pads.. Probably should lean towards mud buddy? But thank you for these videos very interesting and you definitely knowyour jet boat engines..
@@republicansthatdidntvotefo1605 yeah probably or even a noraml outboard i use a 25hp merc and deal with weeds all the time all you have to do is put it in reverse and they will come off
No. I had a tunnel in my Blue Blazer and shortly after buying it weld it up flat. Made everything about the boat better. You can not run shallower with a tunnel. Yes it will give you some protection of hitting your intake.
"what they mean is, pin back and trim up" lol couldn't be more true
Hi Dennis What the brand of the rock ejector. I just pick up a Blazer SS with a 40 mercury jet.
This one is built by Jim Shultz. His email is in the description. Also see more at.
www.outboardjetrockejector.com/product-page/the-kit
facebook.com/pages/category/Sports---Recreation/Outboard-Jet-Rock-Ejector-3021804454498564/
I did better then that I was driving even so it was that shallow
What is the total weight of your new Kaz 1652, gas ,battery, gear and you.. How much water will the boat draft on a drift. How skinny can you run under power ? Why did you choose a 1652 vs a 1656.
Thank's
As it sits in the water full on gas(13 gallons) and me in it will be roughly 1200 pounds (I'm 210). I have yet to measure the draft. As far as shallow goes this video here probably showes that. Probably need 3 or more inches to stay under power. With a 52 inch hull you can stay one piece hull vs a 3 piece.
Thx for ur video s I learned a lot I am doing a 14x48with a 25 jet
And the next one will b a 1655low big river with a long tiller 40 hp jet b safe and have fun
whàler ¹³ 40 hp jet
I got a jet boat
Good explanation Dennis. So many people seem to want to set thier trim and forget it.. Im constantly trimming up or down as I speed up or slow down. I also trim down just slightly to get a little better bite setting up for a tight turn, and slow down slightly so I can use the throttle to power thru the turn. If ur wide open and u cant make the turn thats it. If u have a little throttle left u can give her some gas and use the thrust to help turn.
Absolutely. Save some throttle and trim down for hard turns.
trim tilt always come ? on jets
Not on the small 25 and 30s but on anything bigger yes. Trim can be added to the smaller ones.
How good is that mercurys that haca no one has yet only with paddles used a 40hp and 30hp long leg 4tienpos as they walk ai
I'm new to boating and just bought my first boat (1752 Blazer SS 40hp). Your videos are really helping me. Thanks!!
I have had 2 Blazers. Great boats.
@@DennisBohannan just bought it brand new so I'm watching all the videos I can so I don't bang it all up in the first few weeks 😁
whàler ¹8 tàge best upgradé
whàler ¹³
Great Info, real life experience shared right there💯
my dads got u tunnel in the back maybe 4 or 6 inches wide and a foot or 2 long and he doesnt have to do any trimming
I had a tunnel once. Slowed the boat down way too much. Went from 27 to 32 and could run much shallower and handle better
Olá Denis sou do Brasil como Fasso pra comprar um motor desse
Jgan lupa ngopi sembelum aktifitas
It seems like a jack plate to bring the whole thing up 2~3" would really get the outboard up out the way. With a guy in the rear plus gear weight I would assume you could raise at least 2" and the water intake still be adequately submerged - am I wrong?
Just don’t use the motor at all..I don’t even put a motor on my boat and can glide across the rocks without having to worry about a stupid motor to break. A haha a haha ha.
This is incorrect, the water doesn’t rise that quickly, and when you’re on plan the water is pretty much level with the boat
I think it’s dependent on the speed you’re traveling…..that’s why adjustments are needed on the fly. The water definitely rises, how much is variable depending on speed of the vessel. Hth
is that a 60/40
Yes
@@DennisBohannan i have a 60/40 on a 1652 and was getting about 27-28mph with 2 guys then i added an anchor winch to the front and now im getting 20mph with 1 person should i lower the motor on the jackplate so the shoe is farther in the water? Cant seem to figure out why the boats running way slower besides weight slowing it down in the front
@evanwoyke interesting. I'm not sure without seeing or riding in the boat. Sounds like the added weigh caused a bunch of drag. What type of hull do you have?
How are the jet outboards with weeds ?
If your in some current it can be fine. Dead water and weed not so great.
Weeds/Grass are not your friends on the water...need to keep the boat moving in order for the pump to do it's thing.
@@flex2win yeah that’s what I thought I was just curious
I was thinking of this jet boat engine? I am on A Lake with a lot of weeds hyesan Lily pads.. Probably should lean towards mud buddy? But thank you for these videos very interesting and you definitely knowyour jet boat engines..
@@republicansthatdidntvotefo1605 yeah probably or even a noraml outboard i use a 25hp merc and deal with weeds all the time all you have to do is put it in reverse and they will come off
30 year loan for that engine?
I paid cash, not sure how long banks will do financing on them.
Can you show us how to run on dry ground and across boulders?
Dry ground.
facebook.com/share/v/ipfNqjFqCdvnraXa/?mibextid=xfxF2i
Not boulders but close.
th-cam.com/video/LAtR3nyXdKc/w-d-xo.htmlsi=kIB4IUkBJpglIEdk
Cool
You ever consider adding a tunnel ?
No. I had a tunnel in my Blue Blazer and shortly after buying it weld it up flat. Made everything about the boat better. You can not run shallower with a tunnel. Yes it will give you some protection of hitting your intake.
Do you think it is 6inches or less ? Mike.
If I were to get on front seat it for sure draft 6 inches or less. My fat but in the back with motor it probably draft more than 6.
6 íñçh drafy
Does sand cause damage to the impeller?
It wears it faster but I have impeller I just changed with 700 hours. Most impellers are stainless steel. The liner won't last as long
ñpoe nóe midey water shàker wyer sand barrs firad