Hakko FX-888D Soldering Station
ฝัง
- เผยแพร่เมื่อ 25 ส.ค. 2024
- Taking a quick look at my Hakko FX-888D Soldering Station. This small but powerful soldering station is a great tool to keep on your workbench and is capable of handling anything you can throw at it.
This is not a sponsored video but here's some affiliate links if you'd like to pick one up:
Hakko FX-888D: amzn.to/3HyoISG
Kester 186 Soldering Flux: amzn.to/3MXw9Uq
Needle Tip Bottles: amzn.to/3MS5lVy
Consider becoming a Patron @ / k8mrdradiostuff
Follow me on Twitter. / k8mrd
K8MRD Radio Stuff Shirts:
Happy Skull Guy: grapevineamate...
Tower of Terror: grapevineamate...
Affiliate Links to a bunch of stuff I use:
~~~5% off RigExpert Analyzers at Gigaparts~~~
**Use Code HRMR at checkout for discount to apply**
www.gigaparts....
~~~5% off Comet Antennas at Gigaparts~~~
**Use code K8MRD**
www.gigaparts.....
~~~5% off PO4Power Batteries at Gigaparts~~~
**Use code HRM4 at checkout**
www.gigaparts....
~~~5% off Messi & Paoloni Coax at Gigaparts~~~
**Use Code HRMM at checkout**
www.gigaparts....
**Order Direct from M&P**
Use code K8MRD for 5% off.
messi.it
~~ 5% off Genasun products at Gigaparts
~~~~~Use Code MKGS at Checkout~~~~~
www.gigaparts....
~~~$15 off most purchases over $65 at Radioddity:
radioddity.refr...
~~Amazon Links~~
Icom IC-705: amzn.to/3nISk6S
Icom IC-7300: amzn.to/3rBdQeT
Yaesu FT-891:amzn.to/2XaTkof
Xiegu X5105: amzn.to/2U4jrtM
Xiegu G90: amzn.to/30fszPD
Bioenno BLF-1203W: amzn.to/3bXsRhP
Bioenno BLF-1203AB: amzn.to/39OAW74
Bioenno BLF-1206A: amzn.to/2XaWQ1L
Bioenno 20AH LiFePO4 Battery: amzn.to/2XfZPWT
Bioenno 12AH LiFePO4 Battery: amzn.to/2WHU9kp
Bioenno Charge Controller: www.bioennopow...
Hi-Tec Battery Charger: amzn.to/2YARsSt
Rich Solar 100 Watt Panel: amzn.to/3enp4vD
Carhartt Lunch Box: amzn.to/2xQfbGO
Shakespear 20' Wonderpole: amzn.to/2Rd9IiG
Powerwerx Power Pole Crimping Tool: amzn.to/3eDbpSo
Powerwerx Power Pole Distribution Block: amzn.to/2WHI3Ym
Powerwerx Volt Meter: amzn.to/2IG8AAw
Ailunce HD1: amzn.to/35HqBYZ
Baofeng UV-5R: amzn.to/2Ot3NX7
Tactical Backpack amzn.to/2k6jya7
Condor Rip EMT Pouch: amzn.to/2XjLUPG
iPad mini Bluetooth Keyboard: amzn.to/2IOtI7o
Red Rock Outdoors Sling Pack: amzn.to/2FdCKdf
Portable Operating for Amateur Radio Kindle: amzn.to/2X3I7EU
Portable Operating for Amateur Radio paperback: amzn.to/330xW7J
I may make a small commission on purchases made through the links above.
#hamradio #hakko #solder #FX-888D
![ถามตรงๆ กับ อาจตุพร ทำไม ประเทศไทย ใครเป็นนายก ก็โดนด่า พอออกเเล้วคนคิดถึง!!?? l [Nickynachat]](http://i.ytimg.com/vi/3YFLMXxBGAs/mqdefault.jpg)
![ฮักเทื่อสุดท้าย - บอย ศิริชัย [OFFICIAL MV]](http://i.ytimg.com/vi/-1PoPoQ-B-k/mqdefault.jpg)
Best soldering station I've ever used , simply AMAZING.
I have a Hakko and love it. The best soldering tool that I've ever had.
Mine has served me well since I got it in mid 2014. Yes, the 700-degree setting is the best use of this tool. Like you, I don't use the wet pad anymore. I found as long as I use flux, my dirty tip caused no problems. I do jamb it into the brass "Brillo" sometimes to scrape it clean. I clean my completed soldered areas using a Q-tip or brush dipped in lacquer thinner instead of the traditional denatured alcohol.
I've got one, had it several years. Fantastic....best soldering that I have ever had. I've been home project soldering for more than 70 years.
Very cool!
Picked one up at the Fort Wayne, IN hamfest last fall. My soldering skills improved by a ton immediately.
Ok. Tip about the heat shrink on the helping hand is a good one. Going to fix mine up now
Awesome. Glad to help.
I have this station works like a champ for me and my needs.
Great video Mike. I love my Hakko FX-888D.. like yourself I had cheaper ones when I first got licensed but they all died, The Hakko is just amazing.
73 M0OVG
Suggest you throw away the sponge and replace it with a can of Hakko Tip Tinner Paste (part no FS-100-01). I use double sided tape to hold the can in place. When you dip a hot tip into this paste, it applies a coat of tin on it to keep the tip in top condition when not being used.
The Hakko gets it done. A temperature controlled iron changes the game. The Hakko 888D is the one I recommend to people who want to get a decent iron.
I hear you brother!… The only thing available when growing up (10 years old) was one of these Weller “gun with two-stage trigger” and it seemed that it had 1 megawatt power with the dual prongs… I learned early on that I needed something a lot “gentler” 😂
I also use a very similar vise all the time… mine’s from Dremel.
Great video Mike!
OMG those things are terrible. I've never been able to solder anything with those lol!
This dude kind of reminds me of one of my favorite comedians Big Jay Oakerson.
I have the same one and it is great!
Great video, seems like a great soldering station
ugh, why would they not design this with a temp knob and switch for celsius/Fahrenheit? waaaay too much screwing around to change the temp
Been working with a 35 watt iron from lowes which is not cutting it for me. So I am now ordering this soldering station. Good video.
Glad I could help
Great video Mike, just got my station as well.
Nice 👍
I didn't know what to make of the brass scrubby tip cleaners until I used one. Never going back to water and a sponge.
These look like great soldering irons. I'll have to see if I can find a version for sale in ZL! Thank you for the review, I am using a horrible pen and need to upgrade.
Just make sure you hold it from the handle and not the metal parts 🤣
Hi Mike,
Used the links to buy the Kester flux and the needle tip bottles. Stay safe and have a fun Field Day. 73 WJ3U
Awesome. May your solder flow smoothly!
This is nice if its the only one you get. But it can’t decided if its a bench unit or portable. If you have the money get a full station with a desoldering tool and hot air gun. Then a hand held unit or butane. Love the butane ones! You can adjust the flame so it acts like a hot air gun for shrink tubbing. Plus you can carry them up a tower.
The Milwaukee battery soldering Iron is a great tool, been soldering for decades and its much better than all of those gas irons you can get, even the expensive Gas Wellers. For hot air, well you can use the tip to shrink it iout, or in the workshop you should have a hot air soldeirng gun like Atten model.
Problem with gas irons, I have had a couple blow up in my face because I pressed too hard on the tip, seperating tank from head, also they expel hot air from the sides which if you are not careful can burn you or components.
Nope, stay clear of gas soldering irons!
Thanks Mike I’m been looking at soldering stations for myself. And I will definitely check that one out thanks for the video.
WD5ENH
Steve
You bet
Thanks
Hey thanks so much, I appreciate the tip!
As HAKO is a land mark TS-100 does not step behind. Try to use that station to solder antenna connector in the field or make some fixtures in the field day.
Yeah I already did all of that.
AWSOME 💯👍🙋♂️🍻
Thanks 👍
This is a decent iron for the price but the FX-951 is the way to go.
Pay a little bit more and get it from a certified hako distributor . You’ll get a longer warranty vs Amazon is only like 30 days. And possible fakes on Amazon if you read the reviews. That’s what I did no bs . Make sure you buy extra tips in different sizes and tip runners for storage. If you have extra dough buy the weller that costs a bit more. It has a better core for raven constant heat distribution.
Wooooo!
These work great for guitars?
Nice..................
7:00 is that a "no clean" type of flux
You've been paying attention to the Japanese pronunciation of Hakko :)
About 1.25 fengs high, and 3.5 fengs thick?
Yeah, I'd say that's about right lol
Auto sleep auto time settings available in fx88d??????
The Microcenter special. I work on microelectronics and this thing is amazing. For those who are ragging on him for reviewing a soldering iron, if you aren't soldering in your HAM activities, you are paying too much. Cry some more.
Lol nicely said!
Solder something!
Your intro music always scares the crap out of me Mike!😮
It seems to be a great soldering station bit I wish they made a non-toy looking version and colouring.🤷♂️😄
Please Explain calibration procedure
It just looks like a kids toy to me. Throws me off. I would be afraid my toddler would think its a Hasbro toy
It sort of does hah. But that’s what I like about it. I don’t have kids, so no worries there. I’ve always just thought it looked “fun in a Japanese kinda way .” I finally got one last week. It does not mess around. I should have grabbed one way back in time. I wasted lots of $ being cheap. Also wasted many pcb’s because I didn’t have proper heat transfer. All of a sudden I’m a desoldering master haha. Also there is a lock-out code you can program apparently. It’s just perfect for me, and I find soldering really fun now.. It does “the thing”
I’m not a shill I swear. I’m just passing it along!
@@Rarebirdeffects I appreciate the info I’ll consider it
No worries. Just hoping to straighten out your worries about your child. One more thing not in the video. You can get the same station in silver if you want. I haven’t see it, but maybe more your style. Cheers
As someone who works in electronic manufacturing I appreciate the way it looks since it doesn't remind me of my job when I have it on my desk.
@@147woofs fair point. I have 6 kids and it looks like their toys to me. It is fantastic don't get me wrong just...
Solder iron gun process
I returned mine and went back to my $20 one. Maybe I would also feel differently if I got mine for free.
I'm pretty sure "Soddering " means something different in UK/Australia... lol
Yeah I do love my lawn care!
Good to have a reference for tools we use in our hobby. But bruh... is this a ham radio channel or a product review channel? These days propagation is insane, yesterday I worked New Zealand using a x5105 and a qrpguys efhw deployed at a park, at night. I'd like to watch you hunting some great DX with the insanely good radios and antennas you have. 73s
This is definitely within the ham radio wheelhouse. A lot of hams are builders as well, and having reviews like this help find good products to spend our hard earned money on. If you don't care for the video, don't watch it. There are a ton of ham tubers out there, I'm sure one uploaded something you approve of recently for you to watch instead.
Ham radio was once about improving, expanding communications. Kit building. Now just about contesting and rag chewing. I think it list its way.
Soldering and ham radio literally go hand in hand. How do you think I made half of those great antennas I have? I'll give you a hint, it's with solder.
You say you moved down here to Texas boy? We all say Y'all in the Lone Star State. There are 1,000,000 Yankees & WWW's moving here every year!!!!!!!!!! When in Rome, do as the Romans. I am getting culture shock in my own country sometimes. The Republic of Texas that is. 🤠
Fortunately I was born further South than Texas.