its amazes me how much custom work you guys do, welding and making your own brakets, mounts, manifold, etc. PROPS TO YOU GUYS! hope to be like you guys soon!
petah diegoo same but i get up at 6:00 and leave for thr bus at 6:30 leaving me only 10 minutes at most to watch. but who cares, i can still watch after school.
drill holes in the top piece of the core support and run some like 6inch botls to the top holes of the intercooler it will help make the front end more sturdy
This was sick!! Put a servo on it so you can control the movement with a controller, then add a co2 air cartridge or hydraulic system with a bigger water reservoir so you can turn it into a MEAN water cannon!
Kyle! Thanks for the wake and boost! Hatch is lookin great! I didn't see you make the traction bar. Was it there the whole time? I think once you get all your piping mocked up you should pull everything off and solidify that front end, round the sharp corners, maybe add a bracket or two to reinforce everything. Keep up the great work. Love watching this build and how you guys mix your antics in. That girl's face was priceless.
will you be making plates for the front and welding in some kind of front crash bar?Doesn't have to be super thick. just would hate to see that setup get fucked up in anyway. also please make a video talking about what kind of welding setup you have and why you chose it. I want to go to welding school as well and would like some input from someone who does this stuff all the time. thanks your channel really is the shit.
clean and seal those welds asap but also extend the rad supports.. rubber bushes are good, you should add the bushes for both rad and i/c. it only takes a few minutes and will make it last a long time. Also aluminum and steel don't get along too well so make sure you got something in between them like a Gasket (rubber bush) or at least strong paint. keep up the good work, take your time and think everything through, and this car will last a long time and sell well if you ever need the money
low edge distance on those holes. you need to remake those rad supports to be about 3/4 inch longer to make a hole big enough for rubber supports, otherwise fix it to the supports and put some sort of sealant or paint so the rad doesn't corrode and snap at those holes
+Boostedboiz Have you considered welding gussets under your intercooler and radiator support tabs? Might save the tabs from collapsing if they get stressed.
so close! can't wait until we can see some highway pulls in Mexico !! your going to have problems with traction no matter what so maybe you could add some weight and and make it safer by welding/ bolting some bracing up front with some cheap metal won't be that hard let me know what you think!
Says he used a plasma cutter .......looks more like he caught a wild beaver ,,teased it for a while and then held it in front of the radiator support .
run that fan as a pusher not a puller by reversing polarity. more room and not even on the same side as the wastegate. run water wetter too. otherwise it looks great 👍
its amazes me how much custom work you guys do, welding and making your own brakets, mounts, manifold, etc. PROPS TO YOU GUYS! hope to be like you guys soon!
That shit with the van was fucking hilarious 👏👏👏👏😂😂😂😂
only channel I'll actually wake up to watch when they upload late 👍
petah diegoo same but i get up at 6:00 and leave for thr bus at 6:30 leaving me only 10 minutes at most to watch. but who cares, i can still watch after school.
petah diegoo same here, they are just awesome guys!
wake nd bake to boostedboiz
Thats the spirit!!!
BingestSweetz just finished dabing , cheers bro
Coffeeshop opens in 30 minutes.....
Cheeeechhh!!
just did a .2 dab , good morning y'all I feel great
please fucking spray more people, most laughs I've had all week
Yea more
please this had me crying
SheepShaving spray people on the sidewalk haha
I was dying laughing to the point of crying made my week.
Gotta be one of the funniest vids you guys ever made 😂
BoostedBoiz > All other car channels
Meme was dope!
Henyz what's the name of the song?
Darude Sandstorm
supra8065 Bag Raiders shooting star
You guys are a bunch of hooligans I love it.
"WATER SPRAYING PRANK IN THE HOOD GONE HORRIBLY WRONG (GONE SEXUAL)"
Paid $8 for in-flight WiFi to watch you guys squirt water at cars
byalexandr worth every penny though
That idea with the van was genius!
Should deff do this more often
Damm charle you smack the fuck out of him
Wait to the end of the video and see what I mean
drill holes in the top piece of the core support and run some like 6inch botls to the top holes of the intercooler it will help make the front end more sturdy
lmao never mind i just kept watching and you already said you might do that lmao stoned moment
It's officially bed time!
Felipe Cantera it uploaded at 3:30 in the morning for me😂😂😂
getting so close to getting the Hatch back together. Cant wait to see it back on the road doing some pulls.
The timing you guys post is always spot on
Lmao, good shit man. This is my favorite car channel. Great, real, and quality content.
Kyle make sure you change the intercooler to back door on both sides inlet and outlet...back door on both sides will look sick and clean !!!
" he got beat by a mini van " 😂😂😂😂
This vid was hilarious! Cool to see some stuff of you guys outside of the garage and house
You guys are the only car youtubers that I will consistently watch your videos straight away, great stuff
This was sick!! Put a servo on it so you can control the movement with a controller, then add a co2 air cartridge or hydraulic system with a bigger water reservoir so you can turn it into a MEAN water cannon!
Kyle! Thanks for the wake and boost! Hatch is lookin great! I didn't see you make the traction bar. Was it there the whole time? I think once you get all your piping mocked up you should pull everything off and solidify that front end, round the sharp corners, maybe add a bracket or two to reinforce everything. Keep up the great work. Love watching this build and how you guys mix your antics in. That girl's face was priceless.
Awesome fab work man, I look forward every day to see what you guys are getting done. Keep it up man, been here since 30k subs!
will you be making plates for the front and welding in some kind of front crash bar?Doesn't have to be super thick. just would hate to see that setup get fucked up in anyway.
also please make a video talking about what kind of welding setup you have and why you chose it. I want to go to welding school as well and would like some input from someone who does this stuff all the time. thanks your channel really is the shit.
clean and seal those welds asap but also extend the rad supports.. rubber bushes are good, you should add the bushes for both rad and i/c. it only takes a few minutes and will make it last a long time. Also aluminum and steel don't get along too well so make sure you got something in between them like a Gasket (rubber bush) or at least strong paint.
keep up the good work, take your time and think everything through, and this car will last a long time and sell well if you ever need the money
love waking up at 3 am to watch a video 😎
low edge distance on those holes. you need to remake those rad supports to be about 3/4 inch longer to make a hole big enough for rubber supports, otherwise fix it to the supports and put some sort of sealant or paint so the rad doesn't corrode and snap at those holes
Fascinating to watch theses types of videos.
You want to annoy them , mix water and glycerin.
Hide the nozzle in the grille.
ayyyy i love being up late cus of boosted boiz some entertaining shit while i sit here baked out my mind lol
might want to put some rubber bushings on the mounting post on the bottom of that radiator that steel will wear throw that aluminum pretty fast
Oh, and buy some rubber grommets for your intercooler and radiator mounting lugs. That way you won't have to worry about cracking.
a good and easy tip, if you need some rubber for the radiator under site where the tabs at, just cut it out from an old bike innes tube and good to go
I cried with the meme 😂😂
Flip the cooler upside down. Especially if your making it a backdoor entry. The shorter the piping the quicker you'll get on boost.
I can't wait to see this beast on the road again. It's gonna be fan fucking tastic.
Cant wait to see this beast running !!
Looking less flat rate. Nice!
You really should fab a new core support for that thing... Helps with traction.
hell yeah love seeing the hatch coming along bro!!
Under the radiator and intercooler use old pices of ruber. In my country its called literary inside tire..
Nice get a b5 s4 and that would be sick later on
That jeep dude was sore as fuck haha
RiceFlavouredVTEC looked like 4runner
man, we did this growing up...always good for a laugh
fuck yeah some boosted boiz at 2 am
I can't wait to see it run again that things a beast 👍👍
Meme at the end fuckin killed me 😂😂
+Boostedboiz Have you considered welding gussets under your intercooler and radiator support tabs? Might save the tabs from collapsing if they get stressed.
they sell rubber grommets or gaskets you can probably find for the brackets.
Gotta do more of the wiper spraying it's so good lol
so close! can't wait until we can see some highway pulls in Mexico !! your going to have problems with traction no matter what so maybe you could add some weight and and make it safer by welding/ bolting some bracing up front with some cheap metal won't be that hard let me know what you think!
"Alright I got both my holes drilled" Oh my~
The washer fluid mod was great. 🤣
nice you brought it back that shit was hallarious back then
BoostedBoyz keep the good work. cant wait for summer and see wago's and hatch and MR2 haulin some ass.
.
One of the best Car related Channel Congrats!
I'm glad I found this channel
The kid in that ford looked like mini gayden
Wait that's a girl
dafuq just cause he was white???
SuicideCRX it's a girl bitch
aint no way your bitchass could tell it was a girl in the 2 seconds they showed "it"
wait who TF you talking about? I was thinking the dodge truck was the one you were talking about LOL
Live in Colorado saw you guys at nation wide last time
MrSkaters2 nation wide is on your side
That ko is heavy lol y'all are awesome keep up the awesome uploads!
Charlie's laugh cracks me up
Says he used a plasma cutter .......looks more like he caught a wild beaver ,,teased it for a while and then held it in front of the radiator support .
Did the car pass emissions ?
vMasterMinds been thinking that to myself when he started making the manifold
That car passes everything.
not yet
Didn't he say he found some sort of way around it?
Pretty sure he found some body to sell him an emissions sticker.
holy shit that wiper thing was hilarious. I'm dyingg
Shooting Star meme was cherry on top.
greatest car channel on yt
The frame rate with that sawzall was a trip.
Was waiting all night for this !!!!
The meme at the end was hilarious!
They sounded like Bevis and Butthead giggling in the van.
Boost King
Yea that was a hoot
"We have the biggest intercoolers. They are yuuuuuuuuge!"
Get rubber gromets for those holes. Harbor freight sells them super cheap and they work great 5$
I love that hatch, and that ending was epic LOL!!! 😂😂😂
What traction bar do you have again ? I'm looking to buy one.
ahh yes, kyle back to the usual upload sched.
favorite meme right now
cant wait to see the hatch racing again.
Boost the pitbike!!
these episodes are getting particularly entertaining lately, just need some videos of Honda haters getting destroyed now :)
More washer squirts. Those few videos are why I discovered your channel
shooda used angle iron for the radiator
Damn Charlie..
Now give him a blanket.. 😂😂😂
The channel I wake up to see when they post
Number 1 youtube chan! Keep up the great non-bs work!
hahah I fr be waking up and start watching your vids and pack a fat bowl and just chill haha
That funk ending got me haha Cheers.
This Channel is my drug
run that fan as a pusher not a puller by reversing polarity. more room and not even on the same side as the wastegate. run water wetter too. otherwise it looks great 👍
that should just be the permenant outro now.
my friend's and I use to do the same with the wiper sprayer but we sprayed people walking on the sidewalk
need some truck bushings from a skate board on the radiator mount
The meme at the end 😩😭😭😂😂😂😂😂😂
hahaha that meme is fucking hilarious. keep up the good work bro. cant wait to see the hatch done. Maybe 1 day ill go up there to run you with mine.
my god that meme at the end lmao! perfect
I was laughing like fuck at the washer sprayer. I've done that shit before, too funny.
Legit LOL'd at the spaying water part.
this is friggen hilarious. best video in a long time.
Needs a full version of the smack video edit lol