I was on the fence if I should get one of these systems or use the traditional tank and pressure switch. I will choose this system this was an excellent explanation about how this system works. Thank you
Hi there. So we have a unique problem in our house that plumbers haven’t been able to solve and I think this might be the solution. We have city water and our main house pressure is 75psi. But if we turn on just one fixture (like kitchen sink) the pressure drops drastically to 50. If two fixtures are on the whole house begins to dribble water only. So looking for something that can sense when those drops happen and only boost or maintain higher pressures when it’s necessary because a drop. Will this help?
Hello. A boosting system would definitively help you boost the pressure in your house, as demand increases. Keep in mind that the pump will always work as soon as pressure goes down,(when you open a Fawcett). What you are looking as solution, requires a more sophisticated system with a VFD (variable frequency drive), which is way more expensive. You can find our systems online via www.pumpstoponline.com Have a good day.
The electronic module has two reed switches assoicated with magnets inside the pump chamber. One is the pressure switch which detects the full or dropped pressure in the chamber. When the pressure drops, the pump will start. It will stay running as long as there is flow. The other switch is associated with the flow valve so that while water flows, the valve is open and so is the switch. When flows stops (tap tuned off) then the valve closes and the switch operates causing the pump to stop running. The chip used is usually a LM4093 or similar, which is a quad 2-input (Schmitt trigger) NAND gate. It is wired as a S-R latch, with one reed switch input as a Set and one switch as a Reset. The pump is controlled by a relay, controlled by the output of the latch. I have also used the dual comparator inputs of a LM555 instead. It has a smaller footprint, and is just as cheap and reliable.
Can some one guide me how to built a automatic pump system when water comes in from source the pump will ON automatically and when water stops comes in Pump will stop automatically means no dry run.
When you design a system the maximum pressure that a pipe and fittings can sustain must be more than the maximum pressure of the pump. Ideally pump max pressure should be half that of the pipes
Please I need answers to this question,if the pressure automatic control is working and someone Lock the tap and up it again and find out that water is coming out slowly slowly, what can be problem?
Correct me if I'm wrong, so i can use this for any water pump right? I mean it still can work on any different on off pressure of that particular water pump?
Hello. It depends on the pump that you use; you have to select between the 3 different models that we sell. 22 PSI turn on, 32 PSI turn on or 42 PSI pressure turn on elecronic controller.
My water pump take time to start working sometime even an hour for it to start "pumping". What do you think the reason this happen? And how do i fixed it?
Hello. There could be many reasons for that. It could be pressure, it could be lack of incoming water flow/pressure. It depends on your installation... We highly recommend you to contact a plumber or an experienced contractor to check your system.
There are different configurations in our product portfolio. It all depends on the your aplication. All pumps are fitted depending on your needs. We highly recommend you to consult an irrigation specialist.
Sir, an Electronic control board unit is attached in my 0.5 HP motor pump. The electronic unit is same as like as in your video shows. No other pressure controls in the unit. Then How can we adjest pressure bar with this unit. ? Please mention.
@Baby Solon yes, in most cases especially if your source is a Public Water Service line, it should be as follows: Public water Line>>Storage Tank>> Water Pump (APC is included here) >> Household water Supply
Hello. You would need to select a specific pump model and controller, depending on your application requirements. We highly recommend you get advise from a knowledgeable/ professional contractor. Thanks for your interest in our products.
@@PEARLWaterSystems Well I got a new pressure controller that is able to go up to 22 meters but still unable to get the pump to turn on when I turn on the facet, back to the drawing board.
Mine is automatic switch with very little drops of water it starts auto maticallly infact it keeps on off can u help me set pressure whr it's off on little water leak
Hello there is no setting for little water leak. For the system to work properly , you need to fix the water leak. in the mean time the system will continue to operate that way.
I have the same issue. Had plumbers crawl through our household plumbing and declare there is no leak and yet the pressure drops from 70 to 18psi within two minutes. Consequently, the controller has the pump constantly cycling (one minute pumping to build pressure, two minutes to lose that pressure). Could it be a case of air in the system?
![เกิดใหม่ทั้งทีก็เป็นสไลม์ไปซะแล้ว ซีซั่น 3 - ตอนที่ 70 [ซับไทย]](http://i.ytimg.com/vi/IbBEqbse4Oo/mqdefault.jpg)
I was on the fence if I should get one of these systems or use the traditional tank and pressure switch. I will choose this system this was an excellent explanation about how this system works. Thank you
Simple, clear and to the point! Thanks.
Excellent demo and explanation thank you kind sir
Nice video
Sir is it okay if the apc and water pump is always on.?
Hi there. So we have a unique problem in our house that plumbers haven’t been able to solve and I think this might be the solution. We have city water and our main house pressure is 75psi. But if we turn on just one fixture (like kitchen sink) the pressure drops drastically to 50. If two fixtures are on the whole house begins to dribble water only. So looking for something that can sense when those drops happen and only boost or maintain higher pressures when it’s necessary because a drop. Will this help?
Also best place to purchase and do you know any of them that can plug into regular plug and not need 230?
Hello. A boosting system would definitively help you boost the pressure in your house, as demand increases. Keep in mind that the pump will always work as soon as pressure goes down,(when you open a Fawcett). What you are looking as solution, requires a more sophisticated system with a VFD (variable frequency drive), which is way more expensive.
You can find our systems online via www.pumpstoponline.com Have a good day.
So useful technic
Many many thanks
How this electronic device works? How does it stop when there is no water? How does it start when the water flows afain?
The electronic module has two reed switches assoicated with magnets inside the pump chamber. One is the pressure switch which detects the full or dropped pressure in the chamber. When the pressure drops, the pump will start. It will stay running as long as there is flow. The other switch is associated with the flow valve so that while water flows, the valve is open and so is the switch. When flows stops (tap tuned off) then the valve closes and the switch operates causing the pump to stop running. The chip used is usually a LM4093 or similar, which is a quad 2-input (Schmitt trigger) NAND gate. It is wired as a S-R latch, with one reed switch input as a Set and one switch as a Reset. The pump is controlled by a relay, controlled by the output of the latch. I have also used the dual comparator inputs of a LM555 instead. It has a smaller footprint, and is just as cheap and reliable.
APC with a Starting pressure of 22PSI(1.5BAR) and 17PSI(1.2BAR), Which one is better?
Can some one guide me how to built a automatic pump system when water comes in from source the pump will ON automatically and when water stops comes in Pump will stop automatically means no dry run.
For 10 sec, when the pump is on, and the taps are off, doesn’t it affect the pipe fittings?? Please Reply!
When you design a system the maximum pressure that a pipe and fittings can sustain must be more than the maximum pressure of the pump. Ideally pump max pressure should be half that of the pipes
I am using it for boosting.
How well does it work just for boosting?
Did you connect it directly to a pump or not?
@@josephjoe5603 It should be connected directly on the Pump (APC)
Please I need answers to this question,if the pressure automatic control is working and someone Lock the tap and up it again and find out that water is coming out slowly slowly, what can be problem?
Hi, I store my water in Ibc totes. Which model is good to supply my whole house with 2 bathrooms, 4 sinks, 8 other faucets( used later)?
Correct me if I'm wrong, so i can use this for any water pump right? I mean it still can work on any different on off pressure of that particular water pump?
Hello. It depends on the pump that you use; you have to select between the 3 different models that we sell. 22 PSI turn on, 32 PSI turn on or 42 PSI pressure turn on elecronic controller.
Nice videos. Can you please add subtitles?
Thanks for the feedback. We will keep in mind for future videos. Keep watching our videos.
Can it run on DC?
How do you restart the system manually?
Hello. Press the Red "Restart" button when needed.
@@PEARLWaterSystems if it still doesn't build pressure?
My water pump take time to start working sometime even an hour for it to start "pumping". What do you think the reason this happen? And how do i fixed it?
Hello.
There could be many reasons for that. It could be pressure, it could be lack of incoming water flow/pressure. It depends on your installation...
We highly recommend you to contact a plumber or an experienced contractor to check your system.
Can we use such pump for misting system, if yes what PSI it produce?
There are different configurations in our product portfolio. It all depends on the your aplication. All pumps are fitted depending on your needs. We highly recommend you to consult an irrigation specialist.
Sir, an Electronic control board unit is attached in my 0.5 HP motor pump. The electronic unit is same as like as in your video shows. No other pressure controls in the unit. Then How can we adjest pressure bar with this unit. ? Please mention.
@baby thomas you can adjust the pressure by connecting a presure switch or buying an APC with Integrated Pressure switch inside of it..
Hello sir I have a question this one no need for a tank?
@Baby Solon yes, in most cases especially if your source is a Public Water Service line, it should be as follows:
Public water Line>>Storage Tank>> Water Pump (APC is included here) >> Household water Supply
How do I set it up when my farthest faucet is more then 15 meters away in height?
Hello. You would need to select a specific pump model and controller, depending on your application requirements. We highly recommend you get advise from a knowledgeable/ professional contractor. Thanks for your interest in our products.
@@PEARLWaterSystems Well I got a new pressure controller that is able to go up to 22 meters but still unable to get the pump to turn on when I turn on the facet, back to the drawing board.
We highly recommend you to contact an expert/professional on installations. They will advise you on the proper system for your application
Mine is automatic switch with very little drops of water it starts auto maticallly infact it keeps on off can u help me set pressure whr it's off on little water leak
Hello
there is no setting for little water leak. For the system to work properly , you need to fix the water leak. in the mean time the system will continue to operate that way.
I have the same issue. Had plumbers crawl through our household plumbing and declare there is no leak and yet the pressure drops from 70 to 18psi within two minutes. Consequently, the controller has the pump constantly cycling (one minute pumping to build pressure, two minutes to lose that pressure). Could it be a case of air in the system?
Hi..is this a what they call a smart head?
Not sure about the term. They called this systems in different ways, depending on which part of the world you reside.
have a good day!
חרטטן - מדובר ביזם אחד שכל כמה זמן מעלה מוצר אחר ומבטיח עולם ומלואו - עד שאתה קונה ומגלה שלא עובד