I replaced the transom same way you did on my 1987 Bayliner. I used long drill bits to remove most of the wood in the transom along with some large heavy screwdrivers to scrape the old glued on wood from the fiberglass walls. Designed a long hose to reach on down and vacuum out any residual wood and scraps. The transom was as hard as a rock and lasted the rest of the lifetime of that boat which was decades before it was junked. DIY not to hard. Going to redo the transom on my 1983 V20 that I just started worked on.
I'm out of the technology a bit. 30yrs ago. We only left the outer shell/skin and we started from that layering glass/resin,plywood,glass,resin, plywood,etc,etc That was on a 1970'ish 20ft Grady White. Its 2021 and that same transom is still solid to this day. But I will say, what your doing seems much easier and stronger, and I bet it last forever with no wood. Thanks man, learned a new way today.
I rebuilt my 59 Whitehouse from the inside. 3 layers of 1/2 marine plywood with a layer of chop strand in between each layer. One at a time clamped in place to attain the curvature. Then glassed over the plywood on the inside. Outside with gelcoat remained on the boat. I was thinking of that stuff but it was pricey
I HAVE USED THIS SEACAST SEVERAL TIMES FOR TRANSOM AND STRINGER REPAIR AND IT IS A VERY GOOD PRODUCT. VERY STRONG. ON A WIDE EXPANSE I ALWAYS WOULD GLASS SOME MORE REINFORCEMENT ON THE INSIDE AS AN EXTRA PRECAUTION. BUT VERY VERY STRONG PRODUCT. LOVE THIS STUFF.
5 years later; would you use it again? What would you do differently? Do you still have the boat? I’ve replaced a transom the original way, cut back the deck, the stringers, all from the inside. It seems the seacast cost is about 30% more. I used marine epoxy. It took me about 3 weeks after work in the evenings and weekends. How much time do you think you saved?
Great job! Your videos on this process were very helpful so thank you for taking the time to document it. I'm getting ready to undertake the same process on a 1963 17' whaler. What kind of grinding wheel were you using to remove the gel coat from the transom? I've been using flap disks but they leave a lot of gouges and swirls that have to be filled later. You seem to be using something different?
Doing the same thing to my boat floor and transom with CARBON CORE ,,pours alot better than the lumpy sea cast, Both are better than wood transom, Looks good man.
Just wondering how this has worked out for you now that it's been a couple yrs . I live in Florida not to far from you and was wonder how it worked out for you doing it outside?
Just decided to leave mine like it is some one recently put new Marine ply in it I poured epoxy in the top kinda spread the ply it's super strong now I put a brace inside of the boat that they left out the whole boat was redone floors are awesome in it they just had trouble with the transom
Thanks for making this video. I'll end up having to replace my transom in the next year or 2. I know someone must have already asked this question, so I apologize for asking it again. With it being about 7 years now. How well is the transom holding up, and what size motor do you have on it? ( I am trying to gauge that against my boat which isvery similar in stern design ).... From Lansing, Michigan, hope you and everyone else have a great weekend.
It looks like the transom was way too thin/narrow to handle much load...unless you had a small motor mounted on it. I would have made the transom thicker for more strength.
+Dustin Mayfield - There is a calculation tool on the SeaCast website, I would encourage you to measure and do the math, my calculations were spot on. Good Luck!
Good job man, I am really enjoying this series of videos. One thing that keeps coming to mind.... Would it make sense to put this project in a garage, like a car restoration to make the project take less time? I am even thinking some kind of portable air conditioner as well to make the temps while working more agreeable.
How good would this work if i cant get ALL of the rotted wood out? Couple bits and piece are still stuck on inside. Not much but some i cant get to. Would this form around it or is it too viscous
I ALSO MADE MY OWN VERSION OF THIS WITH BONDO, RESIN, AND MILLED FIBER FOR SOME AREAS THAT I RAN OUT OF SEACAST AND IT WAS AS BULLET PROOF AS THE ORIGINAL SEACAST WAS. I HAVE EVEN THOUGHT OF EXPERIMENTING WITH MY OWN VERSION OF SEACAST FOR REPAIR WORK. SEACAST IS VERY EXPENSIVE BUT IT WORKS.
Are all boats designed like that transom? I have a 15' anchor industries boat that's got a rotten transom on it, and I don't want to get rid of the boat.
you made a mistake, When the seacast was wet you are supposed to apply glass cloth to the top surface and push the cloth down inside to encapsulate the core.. It prevents the sacast from cracking along to top edge. It also saves a ton of finish work. I sanded mine and painted it, no further glasswork needed. Then replaced the alum trim and it looked original.
I don't know sh't about boats, but I do know concrete and when you pour you always use a vibrator or a hammer and tap it to get the air bubbles out because they weaken the concrete but great vid and good job
I'm quite sure poking it with a stick is just fine but like the big cement companies. They would use a vibrating rod but you can simply put a palm sander to the transom and watch the goo vibrate into shape.
We haven't raised our cost for over 3 years. We works so hard to keep the cost (because we know so many hard working people haven't had a raise because of USA economy is still bad ), even though the ingredients have raised. We take every profit to keep our costs lower by purchasing larger amount so we can keep it low. It does cost alot for all the benefits. If you want a permanent replacement, ours is the only one. You get what you pay for.
Florida neighbors are often crude and rude and figure they can do anything on their side of the fence they want to do and if anyone calls code enforcement war breaks out. Neighborhoods not stable with many rentals to snow birds or empty nesters who dream of retirement in Florida more there find it crowded and expensive and move again and again trying to find peace.
![[TH] 2024 PMWC x EWC Group Stage Day 2 | PUBG MOBILE WORLD CUP x ESPORTS WORLD CUP](http://i.ytimg.com/vi/vwIQyCmNIBU/mqdefault.jpg)
I replaced the transom same way you did on my 1987 Bayliner. I used long drill bits to remove most of the wood in the transom along with some large heavy screwdrivers to scrape the old glued on wood from the fiberglass walls. Designed a long hose to reach on down and vacuum out any residual wood and scraps. The transom was as hard as a rock and lasted the rest of the lifetime of that boat which was decades before it was junked. DIY not to hard. Going to redo the transom on my 1983 V20 that I just started worked on.
I'm out of the technology a bit. 30yrs ago. We only left the outer shell/skin and we started from that layering glass/resin,plywood,glass,resin,
plywood,etc,etc That was on a 1970'ish 20ft Grady White. Its 2021 and that same transom is still solid to this day. But I will say, what your doing seems much easier and stronger, and I bet it last forever with no wood. Thanks man, learned a new way today.
Great job, I do just love sat in the garden in good old cool England watching all your hard working boat restoration videos well done ...
I just read this! HA! Right!?
Awesome job man! Good to see how well your craftsmanship and the product worked!
Doing a fine job Captain House!!
I rebuilt my 59 Whitehouse from the inside. 3 layers of 1/2 marine plywood with a layer of chop strand in between each layer. One at a time clamped in place to attain the curvature. Then glassed over the plywood on the inside. Outside with gelcoat remained on the boat. I was thinking of that stuff but it was pricey
I HAVE USED THIS SEACAST SEVERAL TIMES FOR TRANSOM AND STRINGER REPAIR AND IT IS A VERY GOOD PRODUCT. VERY STRONG. ON A WIDE EXPANSE I ALWAYS WOULD GLASS SOME MORE REINFORCEMENT ON THE INSIDE AS AN EXTRA PRECAUTION. BUT VERY VERY STRONG PRODUCT. LOVE THIS STUFF.
+SAILORMAN HARRY - 100% agree! Great product.
Like a boss! Eager to see more!
5 years later; would you use it again? What would you do differently? Do you still have the boat? I’ve replaced a transom the original way, cut back the deck, the stringers, all from the inside. It seems the seacast cost is about 30% more. I used marine epoxy. It took me about 3 weeks after work in the evenings and weekends. How much time do you think you saved?
SeaCast is great for an outboard transom but doing an inboard outboard transom with it can be very tricky. It's still well worth the extra effort.
Great work. I have a 22' Grady White with a weak transom and this looks a lot easier than trying to replace with wood again. How is it coming along?
Lot of hard work but it pays off in the long run great job😊
Yes! Thank you!
Good job. Looks solid!
Great job! Your videos on this process were very helpful so thank you for taking the time to document it. I'm getting ready to undertake the same process on a 1963 17' whaler. What kind of grinding wheel were you using to remove the gel coat from the transom? I've been using flap disks but they leave a lot of gouges and swirls that have to be filled later. You seem to be using something different?
Doing the same thing to my boat floor and transom with CARBON CORE ,,pours alot better than the lumpy sea cast, Both are better than wood transom, Looks good man.
Thanks for the video! How many gallons of seacast did you use? Thanks
What’s the working time of Seacast and what’s the temp range you can use it in
Thank you for posting this.
Awesome job Guys!
What are your thoughts on this? With out having a way to get the air bubbles out is it not going to be weak from all of the voids?
@@dieselyak4842 I would use something to vibrate it while pouring just like doing concrete.
a little over 3 years later, how is it holding up? Is it done?
slow and steady wins the race
Just wondering how this has worked out for you now that it's been a couple yrs . I live in Florida not to far from you and was wonder how it worked out for you doing it outside?
Wouldn't it make sense to make your funnel as wide as the transom for pouring the seacast into?
Did you send the back of the transom for a reason because of the heat that the chemical creates
Great instruction and funny!!
So about four years later, how did it go?
Looks good!
Just decided to leave mine like it is some one recently put new Marine ply in it I poured epoxy in the top kinda spread the ply it's super strong now I put a brace inside of the boat that they left out the whole boat was redone floors are awesome in it they just had trouble with the transom
very good job kaapyton
Thanks for making this video. I'll end up having to replace my transom in the next year or 2. I know someone must have already asked this question, so I apologize for asking it again. With it being about 7 years now. How well is the transom holding up, and what size motor do you have on it? ( I am trying to gauge that against my boat which isvery similar in stern design ).... From Lansing, Michigan, hope you and everyone else have a great weekend.
Awesome work bud!
+terry gonzalez - Thank you so much! It wasn't as bad as I thought it would be.
How many 5 gallons did you use?
How did you get the wood out?
Captain, any update on the Wolf? You left us hanging man!
Good job!!!
Good looking boat,whats the make ?thanks
Any updates on the seacast?
How did it turn out any probkems? What hp?
I wonder how much air is trapped in it ??
I think Carbon Bond would be better to use because its thinner to pour with fewer air bubbles.
You don't have to use a stick to push it down.
It looks like the transom was way too thin/narrow to handle much load...unless you had a small motor mounted on it. I would have made the transom thicker for more strength.
Yaaayyyy Raven! Great to have help.
I'm getting ready to do my 14ft bass boat and was getting a idea. I think 5 will get mine I hope.
+Dustin Mayfield - There is a calculation tool on the SeaCast website, I would encourage you to measure and do the math, my calculations were spot on. Good Luck!
just wow! love this video. curious why you cut the top of the hull sides?
awonenscorned2010 it's a cap, no cutting required just unscrew and lift
i wonder what language Sabine was trying to speak? void is left, formulate your own? locked?
Good job man, I am really enjoying this series of videos. One thing that keeps coming to mind.... Would it make sense to put this project in a garage, like a car restoration to make the project take less time? I am even thinking some kind of portable air conditioner as well to make the temps while working more agreeable.
I would love to do that, but air conditioned space in Florida is expensive. Oh damn it do I wish I could afford that!!! Hahaha!
Plain excellent.
You mention "$800 worth of product." If your transom wasn't curved like that, would you still use seacast or just marine plywood?
How good would this work if i cant get ALL of the rotted wood out? Couple bits and piece are still stuck on inside. Not much but some i cant get to. Would this form around it or is it too viscous
It will form around it. No worries, but get as much of it as you can removed.
How did you clean it out at the beginning. Did you use a saw or something?
I used a chainsaw.
I ALSO MADE MY OWN VERSION OF THIS WITH BONDO, RESIN, AND MILLED FIBER FOR SOME AREAS THAT I RAN OUT OF SEACAST AND IT WAS AS BULLET PROOF AS THE ORIGINAL SEACAST WAS. I HAVE EVEN THOUGHT OF EXPERIMENTING WITH MY OWN VERSION OF SEACAST FOR REPAIR WORK. SEACAST IS VERY EXPENSIVE BUT IT WORKS.
+SAILORMAN HARRY - Nice! I had Seacast reach out to me after I posted this and they were upset I made my own. Lol. It worked great though! :)
@@HouseMadeUS how did you make your own
how much sea cast did it take
12 gallons total.
Janky? Sounds like you made that one up!
Nice vid. How has that transom held up?
Really good.
Is this product available in Canada? If so who sells it
www.transomrepair.net/product_info.php?cPath=1&products_id=34
Are all boats designed like that transom? I have a 15' anchor industries boat that's got a rotten transom on it, and I don't want to get rid of the boat.
If its a fiberglass boat its probably similar yes.
Thanks! I was going to try seacast, but I realized they don't sell it anywhere close to me, so I'll have to use wood I guess
Just contact them via email. They will ship them but you need to pay the shipping costs
you made a mistake,
When the seacast was wet you are supposed to apply glass cloth to the top surface and push the cloth down inside to encapsulate the core.. It prevents the sacast from cracking along to top edge.
It also saves a ton of finish work.
I sanded mine and painted it, no further glasswork needed.
Then replaced the alum trim and it looked original.
I don't know sh't about boats, but I do know concrete and when you pour you always use a vibrator or a hammer and tap it to get the air bubbles out because they weaken the concrete but great vid and good job
Thank you Lee.
What a buzz! I want to put together my own off shore fishing boat but I'm cash poor.
So it’s been 5 years how’s it holding up ?
Solid! 👍🏻
Hi mate where can I buy this from please
If you search for SeaCast on google you can find distributors. 👍🏻
good vid. I bet you are going to wish you would've put some cardboard down on your concrete.
when did it sink?
This one never did sink. It was just rotten from being old.
I'm quite sure poking it with a stick is just fine but like the big cement companies. They would use a vibrating rod but you can simply put a palm sander to the transom and watch the goo vibrate into shape.
I kept thinking the same thing
my wife vibrator would have serve too
@@fernandovina1052 too funny but true
GREAT IDEA JEFF
@@fernandovina1052 YOU WOULD HAVE TO GET ALL THE FIBERGLASS STRAND OFF IT BEFORE YOU USE IT AGAIN. MAN THAT SHIT WOULD HURT LOL.
For added strength perhaps fiberglass rebar...
Where did you get your hands on tin foil?
you're an idiot
Where can i buy this stuff in europe?
Not sure, but you can contact Eco-Wolf in the Florida here and see if they can get you in contact with an EU rep. - www.transomrepair.net/
they sell it on ebay,order it online.
I would have used a palm sander and vibrated that transom while poring to get all the air out
Yeah that would have helped.
3 years after I made the transom with Seacast it cracked...
If this boat is mine and I would flat the transom and provide strong support for new outboard engine.
I give you a 9.789 on that dive. Looks great mate. Put in comments how it holds up!!!!!
Last time I saw it, it was solid. I’ll have to ask the guy I gave her to if she is coming along.
@@HouseMadeUS Have you asked the guy? Lol
Permanent transom
105, 106. 220, 221, whatever it takes.
$800?? wow
I was told by an old guy. to use wax on the bolts
Yes that can also work.
We can't buy any thing in Australia. Very expensive to buy in Australia.
Two words: Drop Cloth
Yeah man, haha! 😁
Too bad that stuff is so expensive! I would redo my whole boat with it.
We haven't raised our cost for over 3 years. We works so hard to keep the cost (because we know so many hard working people haven't had a raise because of USA economy is still bad ), even though the ingredients have raised. We take every profit to keep our costs lower by purchasing larger amount so we can keep it low. It does cost alot for all the benefits. If you want a permanent replacement, ours is the only one. You get what you pay for.
what a neighbor: fiberglass dust blowing around everywhere - great for babies next door etc.
Waaaaaaaaaaaaaaaaaaaaa
you respond like the idiot you are (really it should have been [in your vocab most days] you: "duuuuuuuuuuuuuuuuuuuuhhhhhhhhh" :):):):) ... ).
🤣🤣🤣
Seacast $800 really Bros? That's a lot of money there charging people
You’re telling me!!
I find it difficult to believe that you didn’t put something down to cover your concrete. What a mess!!!
with all due respect how much glass pollution did you share with all your neighbors and your garden ???????????????
LOL
Remember fiberglass made from sand and the garden will survive.
Florida neighbors are often crude and rude and figure they can do anything on their side of the fence they want to do and if anyone calls code enforcement war breaks out. Neighborhoods not stable with many rentals to snow birds or empty nesters who dream of retirement in Florida more there find it crowded and expensive and move again and again trying to find peace.
It was probably less than the amount of incessant yapping of their lap dog.
I hope that whoever has the boat doesn't have to repair that transome because he's going to have to cut half of the boat just saying