this size is easier to centerize the cone. smaller than 4-5" or bigger than 12"-15", often after 2-3 months, you hear the noise of scratching and need to recone agaaaain 😫 a few pieces of thin papers must be slided inside center coil to prevent this problem till glue will be dried 😉
Basic repair principles are ok except I would be shocked if the coil didn’t rub on the magnet when completed. You must use spacer shims for proper coil centering. Also your coil depth is guess work.
You shouldn't scrape the insolation off the coil wire either. Instead you must either use molten solder or lighter flame to do so. Good work but you will get 7 out of 10 from me.
Please take care , many Amaturist seekers will try to take this as a basic ingredient to learn & practically perform this project. All corrected steps in the suggestion box be taken care of and new recording be uploaded for everbodys' s benefit.
Yo no me dedico ese pero sinceramente lo hago mejor que él nunca me he quedado mal una bocina yo mejor no sabía ni un video así con ese tipo de forma de trabajar que me estuvieran viendo wowww
Jeżeli miałby to być film instruktażowy to nie polecam naprawy głośników w przedstawiony sposób, jest wiele nieprawidłowości - Nie oddałbym mojego głośnika do naprawy w ręce tego montera
Pardon my ignorance on speaker basics - would like a tiny direction for my problem. I bought a 8inch 50 watt woofer (not sub woofer) about 15 years back, used it for few hours and it sounded good. I opened it today and connected it to my amplifier and it outputs too little volume. I gently pushed the cone and spider up, and the volume goes up and it vibrates well. How can I fix it? The spider feels hard... the soft rubber on the outer edge of the cone is soft/flexible...
This is a old video but you learned the hard way didn't shim it it probably rubbed and shifted oh well you can break it down and re do it recone kits cost a lot of money now day
Por eso yo hago mejor mis trabajos me quedan súper excelentes dedico a eso simplemente yo nomás vi una persona una ocasión ahora puedo embobinar o enconar de una jbl para
Me bas a disculpar pero ese trabajo está mal echo porque aplicarte el pegamento sin antes colocar los sentradores sin los sentradores esa bovina te va quedar rosando y va a sonar horrible
Делаю всё наоборот. Это не удобно и очень долго... Зачем было обрезать катушку? И плетёнки нужно было ставить сразу, а не при приклеевании подвижки? Это не правильно.
он забыл что надо центровать, что-то измерял, я уж думал сейчас правильно выставит центр катушки по центру железа, а она улетела на дно магнита, он так и приклеил, лопух, 99% пишут nice work )))
E muito simples de monta um alto falante mais ele está fazendo o proseso mais difícil e só calsar. 1 passo. Calsar abombina. 2 depois passa acola. Nas parte metálica 3 cola abombina e 4 desses as cone faz a saldagem da bombima para os conequitores do alto falante. Desse o cone e o tapes.
Buenas noches Excelente la tutoría. Aquí en Campeche, México, los técnicos usan resistol blanco # 850. En la tutoría no se cómo se llama el pegamento que usa. Será que lo vendan aquí en México y con que se pide. Habrá en cualquier eléctronica. Saludos cordiales. Desde Nunquiní, Campeche, México.
For the circuit diagram please visit here
shorturl.at/FNS56
How did you decide magnetic center and physical center of voice coil?
this size is easier to centerize the cone. smaller than 4-5" or bigger than 12"-15", often after 2-3 months, you hear the noise of scratching and need to recone agaaaain 😫 a few pieces of thin papers must be slided inside center coil to prevent this problem till glue will be dried 😉
They didn't center the voice coil. This is a bad video because they did not use shims.
Basic repair principles are ok except I would be shocked if the coil didn’t rub on the magnet when completed. You must use spacer shims for proper coil centering. Also your coil depth is guess work.
How do you decide coil depth
very unprofessional... no voice coil balancing bad video
At what point did he center the coil?
How do you identify positive and negative
sir, how about clearance, voice coil between, bottom center mag net?
Professional 🔈🔈🔈🔈🔈
Ramses elektronik olarak aramızda görmekten mutluluk duyarız görüntüleme ve ses sistemleri
Spider alternate not proper work. never then originally
Please visit for amplifier circuit diagram
electronicshelpcare.net
I am also in electronic electrical mechanical field
You shouldn't scrape the insolation off the coil wire either.
Instead you must either use molten solder or lighter flame to do so.
Good work but you will get 7 out of 10 from me.
Даже не сомнивался что он его не будет включать на видео))) магнитный зазор не выставил.
да он там пиздец всё криво сделал, 100 литров клея вылил
Bhai 1 speaker repair price please
Worst speaker repair ever lol
Tnx master..we are watching 🙂😌🙂 very useful technic
Please take care , many Amaturist seekers will try to take this as a basic ingredient to learn & practically perform this project. All corrected steps in the suggestion box be taken care of and new recording be uploaded for everbodys' s benefit.
You cannot do it exactly without putting spacer along the sides of the coil to have the same clearance..it should be done carefully.
X ray or fan binding wala kagaz is the best for spacer
Muito gasto de araldire, sem chapa não consigo isso
👍👍👍👍👍👍
Yo no me dedico ese pero sinceramente lo hago mejor que él nunca me he quedado mal una bocina yo mejor no sabía ni un video así con ese tipo de forma de trabajar que me estuvieran viendo wowww
Jeżeli miałby to być film instruktażowy to nie polecam naprawy głośników w przedstawiony sposób, jest wiele nieprawidłowości - Nie oddałbym mojego głośnika do naprawy w ręce tego montera
TE FALTO CENTRAR LA BOBINA
Pardon my ignorance on speaker basics - would like a tiny direction for my problem. I bought a 8inch 50 watt woofer (not sub woofer) about 15 years back, used it for few hours and it sounded good. I opened it today and connected it to my amplifier and it outputs too little volume. I gently pushed the cone and spider up, and the volume goes up and it vibrates well. How can I fix it? The spider feels hard... the soft rubber on the outer edge of the cone is soft/flexible...
I have the same problem with two entire media rooms. Did you ever find a solution?
Y que no centran la bobina? Luego roza y se escuchan ruidos extraños en la bocina!!
wrong method the coil enlinment
Tak jelas...
Pasang spool speaker nggk pakai ukuran...
Saya tukamg pasang spool bro..
AMAKURUYANYUBANTUBANJYE
muy mal la reparación de la bocina de lo más crítico fue q no centraste la bobina lo pegaste para hacer el vídeo y mal cortado el cono... Muy mal.....
Mali Ang process sa pag gawa
В руки насрать за такую работу. И что б воды не было...
ভাই বলছি এস পি 2 কত টাকা পড়বে,,,,,,,, কমের পরে বলেন তো
Super demo thankyou bro God bless your work
This is a old video but you learned the hard way didn't shim it it probably rubbed and shifted oh well you can break it down and re do it recone kits cost a lot of money now day
ابھی شاگرد ہو 3 غلطیاں کی ہیں Now the student has made 3 mistakes. الآن ارتكب الطالب 3 أخطاء. अब छात्र ने 3 गलतियां की हैं।
இந்த செய்முறை தவறானது இதை யாரும் செய்யாதீர். டோடல் வேஸ்ட்.
Obs tem que centralizar o centro da bina para não arrastar no canto para não fazer ruído. Isso ele não amostra no vidio eu já fiz varios
No sabes....hoy ..y loscentradores estás weeeeyyyy....😁😁😁😄😁😄😁
Por eso yo hago mejor mis trabajos me quedan súper excelentes dedico a eso simplemente yo nomás vi una persona una ocasión ahora puedo embobinar o enconar de una jbl para
Como dijieron la mayoria de todos ..le falto el centrado de la bobina y cuanto milimetros deja de bobina hacia arriba del nucleo del bobinado
Me bas a disculpar pero ese trabajo está mal echo porque aplicarte el pegamento sin antes colocar los sentradores sin los sentradores esa bovina te va quedar rosando y va a sonar horrible
Делаю всё наоборот. Это не удобно и очень долго... Зачем было обрезать катушку? И плетёнки нужно было ставить сразу, а не при приклеевании подвижки? Это не правильно.
Lem apa yg dipake utk ngelem memran spiekerx gan
Mal todo mal primero se pega la membrana con el cóno después pisaconos de último la bobina para centrarla bien
Faltou centralizar a bobina com um papel
Tô esperando ele centralizar tbm faltou
Катушку в зазоре отцентровал по верхнему краю шайбы. Не правильно. Центр шайбы с центром катушки должны совпадать.
Он вообще будет играть?😅
он забыл что надо центровать, что-то измерял, я уж думал сейчас правильно выставит центр катушки по центру железа, а она улетела на дно магнита, он так и приклеил, лопух, 99% пишут nice work )))
Naaku
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
What kind of adhesive can be used to repair small slit on JBL L110 driver?
E muito simples de monta um alto falante mais ele está fazendo o proseso mais difícil e só calsar. 1 passo. Calsar abombina. 2 depois passa acola. Nas parte metálica 3 cola abombina e 4 desses as cone faz a saldagem da bombima para os conequitores do alto falante. Desse o cone e o tapes.
Buenas noches
Excelente la tutoría.
Aquí en Campeche, México, los técnicos usan resistol blanco # 850.
En la tutoría no se cómo se llama el pegamento que usa.
Será que lo vendan aquí en México y con que se pide.
Habrá en cualquier eléctronica.
Saludos cordiales.
Desde Nunquiní, Campeche, México.
Perdón.
Con qué nombre se pide.
Perché il mio woofer da 18 pollici emette un suono tipo plac ad alto volume?
Very wrong...disalign voice coil when it dries the glue.. No guide for the voice coil
electronicshelpcare.net/led-music-level-indicator-circuit-diagram/
Essa montagem desse alto falante ñ ta correta ñ causou a bobina montagem muito mau feita
Bien por tu vídeo amigo oye una pregunta , qué tanto debe d entrar el embobinado ? Gracias d antemano amigo.👍
Good
Sir meri chupinchena speekar repai ki kavalachiña parts perrulu cheppaledhur
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
serviço ruim não centrou a bobina com negativo,não entendi.
Hi
Bhai tu professional hota na to is type se nahi banata speaker btw temporary try Kiya tune🤣
Coil adjustment aise kon karta h bhai🤣
sa sayad at sa sayad talaga ang Voice coil nyan parang may mali talaga
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
🙏👍👍👍👍😎🙏🙏🙏👍🔥🔥🔥🔥🙏🙏🙏🙏🙏🙏👍👍👍👍👍👍😎😎😎😎😎😎😎😎😎😎😎😎❤️❤️❤️❤️❤️❤️❤️❤️❤️😭
Com certeza vai raspar.👎
QUE PORQUERIAS.... BAD, BAD, BAD, BAD, BAD, BAD...............
Boss.mgkno pplit sau Ng nsa video m my apat kc akung dedose n spekear
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
100% sasayad ang voice coil nyan.
He could have extended it till the sound coming from the speaker
Yun guys pahampas lng po I'm done
Mewa ganne kohenda
electronicshelpcare.net/how-to-make-speaker-crossover/
Cara pemotongan dan pengeleman saya kurang suka
පරන ස්පීකර් තිබුණාට රෙපෙයාර් බෑනේ ඒහින්දා අදවත් බඩු ගන්න තැනුයි නමුත් දාන්න
හා
Work Finnishing not good
Sangat rapi dan keren,sangat ber manfaat sekali
D kp type ang pag gawa madumi pabilosan no good
Es un desmadre para repara el bajo. Falto centrar la bobina
Very stupid way to rewind speaker
I mean, I'm not the most ocd person there is, but that membrane cut was something else.
Demasiado chambón..
Es que ese Joven hace su trabajo a su modo
Can you use super glue (cyanoacrilate), instead of epoxy?
No
What is name of all components. Like voice call and the other?.
Tarik sis semangko...
Paling di tes spoolnya kena boddy
This video shows you how not to replace a cone. The results of this will be a rubbing voice coil and bad sound.
Thanks for sharing .
Ye galat tarika hai spekar sarvice karne ka
Very good
Te faltó el centrado de la bobina
This is not perfect
Ahuja 400 wat mein Kitna number ka koil lagta hai bhaiya bataiye na please mere ko kharidna hai
electronicshelpcare.net/how-to-make-speaker-crossover/
Sab tu bekar video he ready krna ne oda 👎👎👎👎👎👎👎👎
அண்ணா இது என்ன பேஸ்ட் கொஞ்சம் சொல்லுங்கள் அண்ணா
which types of glue is needed
The type that shoe maker uses.
no centraste la bobina
There something wrong coz will not be put clearance both sides inner and outer of coil...inside magneg.
Cortou o cone de qqr jeito. Só aí já foi matando o fluxo de médio grave do speaker. Forma bastante grotesca de reparar.
Anung name po NG pandikit nyo
I bought speakers and the woofer doesn't have the connection where the +/- wires go
Am si eu un defuzor de bobinat
Are you trying to beat the speed of light???
El párese que está aprendiendo