You can buy this spot welder from the links below Spot welder 12v - 🛒 lzda.store/SPOT_WELDER_12V Spot welder with LED - 🛒lzda.store/spot_welder_LED You also need a 3s Lipo battery and an XT60 connector 3s 2.2Ah 50C Lipo Battery - 🛒lzda.store/Lipo_2.2Ah_50C XT60 Connector - 🛒 lzda.store/xt60_connectors or a 12v Lead Acid Battery Deep Cycle VRLA Lead Acid 12V 50AH - 🛒 lzda.store/deepcycle_50Ah_vrla Or a LiFePO4 12v battery 🛒lzda.store/12v_24Ah_lifepo4_batt
@@kirito-lk9eg its a safety device so it is recommended na gamitin natin ito. You can do without a BMS but it is not safe for the battery. Will do an in depth video on this topic soon para mas mapaliwanag at maidemo natin para mas maintindihan natin.
Most excellent video. You're a awesome gentleman for creating this video for everyone to get an understanding of this spot welder. I appreciate your work and impressive effort. Thank you very much! I purchased the exact same spot welder from Wish recently. It is lacking 1 wire but I can manage finding an adequate wire. Once again, thank you so much!
mayroon ako niyan. kung spot welding ang Pag-usapan expected malakas ang current na kailangan so dapat ang electrode, wire input & output tsaka traces dapat makapal para kayang e Mannage ang large current. sabi sa instruction up to 0.12 mm nickil strip pero noong inapgrade ko kayang mag weld sa 0.3mm nickel strip. tapos ang mosfet nasa normal temperature. syempre dapat ang battery then may sapat na current na kayang mag melt ng 0.3mm nickels strip.
Oo nga sir manipis yun mga wires na kasama dapat talaga makapal para mas malakas mag weld. Gawan ko part 2 ang video na ito papalitan ko yun mga wires at mas magandang electrode and itotorture test natin para makita ko kung madali ba masira. I did measure the current while spot welding and level 1 is at 300Amps and level 5 is 500 amps. Of course yun current ay based parin sa battery mo kung ano ang kaya nya iprovide pag mahina battery mo mahina rin current na dadaan.
@@SolarMinerPH cheap spot welding not base sa current flow nagbase sa millisecond the more longer time the more stronger weld nag review den ako, most review vlog ko cheap spot welder boss.
Buena mano! Arrived from Shopee na yung Lvtopsun 100 ah namin today. Pero walang volt meter generic kaya ito? Tips na rin sa voltage parameter settings for SRNE 40a and SNADI 1000 12v. Equalization?
Lods sa power bank namn alin mas maganda gagawa ako Ng 3s10p or 3×10 18650 na naka series na 12v labas niya TAs gagamit Ng converter to 5 volts na 3.0 quick charge or 3p10p or 30pcs na 18650 na naka parallel na gagamit Ng input na 5v TAs out na 5v TAs 3.0 quick charge din? Alin mas okay sa dalawa boss same mah pa din ba yan or d na
Ano yun 3p10p? 30p ba dapat yun? Same watt hour parin po yan. Its always better na malapit ang voltage ng battery mo sa voltage ng paggagamitan mo to minimize conversion losses. So kung 5v ang kailangan mo, for me 30parallel is better.
Boss pwede gamitin ung battery Ng tricycle na 12 volts ung 12N12-3B ?or tatlong 18650 na naka series para mabuo 12volts TAs pwede ba gagamit Ng bms na 40A or 60A?
Yun battery ng tricycle baka pwede. Parang isa sa recommended yun. Sa 18650 kulang ang tatlo lang. Di rin pwede yun bms dahil 150amps pataas ang need mo. Wag mo na kabitan ng bms kung gusto mo 18650 pero dapat madami nakaparallel para kaya nya iprovide 150amps pataas
@@SolarMinerPH TAs boss sa shopee ko Kasi binili may nakalagay na note na the battery should not exceed 60A or the tube may burst masisira po ba ung mini spot welding kung sumobra Ng 60 A ung battery?
issue nyan hinde pwede sa heavy use. Depende sa bilis, mga 30-50 sunod-dunod mainit na yung electrodes at mga mosfets. Pwede naman maglagay ng heat sink sa fets pero yung sa electrodes pakapalan na lang ng kalyo.
kung spot welding ang Pag-usapan expected malakas ang current na kailangan so dapat ang electrode, wire input & output tsaka traces dapat makapal para kayang e Mannage ang large current. sabi sa instruction up to 0.12 mm nickil strip pero noong inapgrade ko kayang mag weld sa 0.3mm nickel strip. tapos ang mosfet nasa normal temperature.
I assumed na na wrong type ka lang at 1500mAh yan at hindi 1500Ah (Ah vs mAh) kaya sabi ko hindi. Anong drill po ba yan at ganyan kalaki na 1500Ah ang battery nya? Ang 100Ah na 12v battery ay singlaki ng battery ng sasakyan at kung yan ay 1500Ah bale parang 15x na battery ng sasakyan ang nakakabit sa drill nyo?
I don't know exactly how much amps you need dahil wala ako pang sukat ng surge current. Online sources say 40 to 400 amps. You can probably put a super capacitor in parallel para kahit 1A na power supply pwede. You just have to wait to charge the capacitors every spot weld.
You will encounter board die if set to level 4 or 5. will on again after disconnect and reconnect + or - power to overcome that seri 22 ohm resistor on diode M7 th-cam.com/video/1ZCbLdymJIs/w-d-xo.html
You can buy this spot welder from the links below
Spot welder 12v - 🛒 lzda.store/SPOT_WELDER_12V
Spot welder with LED - 🛒lzda.store/spot_welder_LED
You also need a 3s Lipo battery and an XT60 connector
3s 2.2Ah 50C Lipo Battery - 🛒lzda.store/Lipo_2.2Ah_50C
XT60 Connector - 🛒 lzda.store/xt60_connectors
or a 12v Lead Acid Battery
Deep Cycle VRLA Lead Acid 12V 50AH - 🛒 lzda.store/deepcycle_50Ah_vrla
Or a LiFePO4 12v battery 🛒lzda.store/12v_24Ah_lifepo4_batt
Pwede po ba yung 32650 na battery? Without bms?
@@kirito-lk9eg its a safety device so it is recommended na gamitin natin ito. You can do without a BMS but it is not safe for the battery. Will do an in depth video on this topic soon para mas mapaliwanag at maidemo natin para mas maintindihan natin.
Most excellent video. You're a awesome gentleman for creating this video for everyone to get an understanding of this spot welder. I appreciate your work and impressive effort. Thank you very much!
I purchased the exact same spot welder from Wish recently. It is lacking 1 wire but I can manage finding an adequate wire.
Once again, thank you so much!
Your cell connections on that LiFePO4 bank are probably going to be your biggest hurdle. Just the overall lack of properly sized wiring.
Ito hnhanap ko... boss ano recommend mo na spot weld..link po sna..tanx..
mayroon ako niyan. kung spot welding ang Pag-usapan expected malakas ang current na kailangan so dapat ang electrode, wire input & output tsaka traces dapat makapal para kayang e Mannage ang large current. sabi sa instruction up to 0.12 mm nickil strip pero noong inapgrade ko kayang mag weld sa 0.3mm nickel strip. tapos ang mosfet nasa normal temperature. syempre dapat ang battery then may sapat na current na kayang mag melt ng 0.3mm nickels strip.
Oo nga sir manipis yun mga wires na kasama dapat talaga makapal para mas malakas mag weld. Gawan ko part 2 ang video na ito papalitan ko yun mga wires at mas magandang electrode and itotorture test natin para makita ko kung madali ba masira.
I did measure the current while spot welding and level 1 is at 300Amps and level 5 is 500 amps. Of course yun current ay based parin sa battery mo kung ano ang kaya nya iprovide pag mahina battery mo mahina rin current na dadaan.
@@SolarMinerPH cheap spot welding not base sa current flow nagbase sa millisecond the more longer time the more stronger weld nag review den ako, most review vlog ko cheap spot welder boss.
18650
3s 3p gmit ko mhina,nag spark lng x pg s gilid ko nilagy ung probes
H03BC ang handle, at AHS 30A Jaw ng crimper
Boss asking if pwede gamitin yung nss na 7.2 lead acid battery?😊
try ko po not sure kasi if it will work
"tingnan natin kung may pagsabog na magaganap" 😅😂😁
salamat dito sir!
Buena mano! Arrived from Shopee na yung Lvtopsun 100 ah namin today. Pero walang volt meter generic kaya ito? Tips na rin sa voltage parameter settings for SRNE 40a and SNADI 1000 12v. Equalization?
Baka lead acid yun nabili nyo po. Magkano po ang bili nyo?
Boss pa review ng magandang Inverter nman jan.bka Meron ka, Tnx
Lods sa power bank namn alin mas maganda gagawa ako Ng 3s10p or 3×10 18650 na naka series na 12v labas niya TAs gagamit Ng converter to 5 volts na 3.0 quick charge or 3p10p or 30pcs na 18650 na naka parallel na gagamit Ng input na 5v TAs out na 5v TAs 3.0 quick charge din? Alin mas okay sa dalawa boss same mah pa din ba yan or d na
Ano yun 3p10p? 30p ba dapat yun?
Same watt hour parin po yan. Its always better na malapit ang voltage ng battery mo sa voltage ng paggagamitan mo to minimize conversion losses. So kung 5v ang kailangan mo, for me 30parallel is better.
@@SolarMinerPH edi 3.7 volts pa din un lods tsaka ibig sabihin non 3 series 10 parallel
Boss pwede po ba gamitin pang suply yong 18650 na ginamit nyo sa video...
kailangan 20Ah or more
@SolarMinerPH diba 25A poh drain nyan HG2 pweede 3S2P para 50 amp na ang total drain..
Hindi gumagana sir, 3S2P rin na config yung gamit ko sobrang hina hindi maka weld
Using Panasonic ICR18650-28A
@scar_onefiftysix ganon din sakin ehh kaya umorder nlng ako RC battery 11.v 60C dlawa... Kailangan daw high drain...
@@jeypeeem9 same sir 60C para sure kasi 45c minimum
Sir Pwde din Po ba iconnect ito sa 12v power supply adopter?
hindi po, kailangan po battery
pede po ba dyan sir ung 4s 5p na 32650 lifepo4 battery??
@@kuyatechmac0127 pwede
boss.. mga anung klaseng battery pa kaya pwede kong ikabit sya as source of power ?? pwede ba sa battery ng motor ???
20-45 ah daw na lead acid ang pwede.
sir pwede kaya gamitin ung power supply dito? meron ako dito power supply tulad nung nasa isang video mo 6a 12v-30v
hindi po pwede
@@SolarMinerPH salamat po sir
Pwede gumamit ng soldering iron if wla pong pang spot welding? Salamat po
Pwede naman po basta bilisan nyo lang para hindi masstress yun cells.
have you tried using regulated power supply? i have a 30amp regulated PS with 2 large caps bigger than a drinking glass.
its possible. Havent tried it yet.
@@SolarMinerPH can you try it? so i have an idea before buying the module. thanks.
if I have the time I will try it. Currently super busy right now.
puwidi bang gamitin ang 12v voltage regulator sa spot welder.
hindi po
Boss pwede gamitin ung battery Ng tricycle na 12 volts ung 12N12-3B ?or tatlong 18650 na naka series para mabuo 12volts TAs pwede ba gagamit Ng bms na 40A or 60A?
Yun battery ng tricycle baka pwede. Parang isa sa recommended yun. Sa 18650 kulang ang tatlo lang. Di rin pwede yun bms dahil 150amps pataas ang need mo. Wag mo na kabitan ng bms kung gusto mo 18650 pero dapat madami nakaparallel para kaya nya iprovide 150amps pataas
@@SolarMinerPH boss mga ilang 18650 na battery na naka series kailangan pwede ba kahit 3×5 lang or Ilan po ba dapat para ma ayos po
@@SolarMinerPH TAs boss sa shopee ko Kasi binili may nakalagay na note na the battery should not exceed 60A or the tube may burst masisira po ba ung mini spot welding kung sumobra Ng 60 A ung battery?
Yes po, posible po masira kapag sumobra naman yun current.
@@SolarMinerPH
Cutter lang ang ginagamit kong pang crimp
Pwede ba jan sir Yung ebike battery na gel type 25Ah pang supply?
yes pwede po
Good days ser ok lng b gamitan ng power suply na 12v30amps kaya po ba masisira ba un power suply ko
Hindi po magwowork you need high amp na battery lang ang kaya magprovide
Sir, pwede po na 12v DC powersupply if walang battery?
hindi po. You need a battery na may mataas na discharge rate
pwede bang hindi sa lipo batteries gamitin yan halimbawa sa power supply
Hindi pwede sa power supply
Idol.my gnawa ako backup generator 18650 3s 12p.nag bbawas xa kht nd gnagamit
Baka may isa ka napasama na bad cell. Mataas internal resistance siguro kaya nagdidischarge.
Very informative video. Salamat sa tips sir.
kung gagamit ako ng 18650 lithium battery, mga ilan piraso yun sir?
30-45 pieces in 3s
@@SolarMinerPH it means in 1 row series is 15 lithium battery?
Kaya po ba nyan 4s 1p lipo4 5.5ah walang bms?
hindi
Dilikado po ba ang spotweld or nakaka kuryente ba?
hindi pa naman po ako nakukuryente. low voltage high current po yata yan.
Ilang volts Yan supply sa spot welder boss
12v
Pwede po ba yang ganyan sa stainless like kaserola?
hindi ko pa po natry. Most likely hindi po pwede dahil mahina lang ito kailangan manipis lang para magwork
issue nyan hinde pwede sa heavy use. Depende sa bilis, mga 30-50 sunod-dunod mainit na yung electrodes at mga mosfets. Pwede naman maglagay ng heat sink sa fets pero yung sa electrodes pakapalan na lang ng kalyo.
Try ko mamaya sunod sunod. Check ko temperature nya.
kung spot welding ang Pag-usapan expected malakas ang current na kailangan so dapat ang electrode, wire input & output tsaka traces dapat makapal para kayang e Mannage ang large current. sabi sa instruction up to 0.12 mm nickil strip pero noong inapgrade ko kayang mag weld sa 0.3mm nickel strip. tapos ang mosfet nasa normal temperature.
battery ng mga 4wheels na 12v pwde ba?
pwede po
Pwede ba yan Sa battery ng drill na 12 V
na may 1500 ah
kulang po
@@SolarMinerPH diba sabi mo po sa ibang nag comment 150 ah need dun
eh 1500 ah na po yung sa battery ng drill ?
I assumed na na wrong type ka lang at 1500mAh yan at hindi 1500Ah (Ah vs mAh) kaya sabi ko hindi. Anong drill po ba yan at ganyan kalaki na 1500Ah ang battery nya? Ang 100Ah na 12v battery ay singlaki ng battery ng sasakyan at kung yan ay 1500Ah bale parang 15x na battery ng sasakyan ang nakakabit sa drill nyo?
@@SolarMinerPH yung dayway motorcycle battery na may 3ah pwede po ba yun ???
@@badodlessss you need at least 20ah
Sir pwedi yan e direct 150ah battery yong spot wild?
pwede po
Sir kaya ba yan sa 32700 cell na flat ?
yes
gaga na kaya yan sa 12v adaptor?
hindi po
Puede nmn ata 2x mo i spot weld para mas mkapit
I spot weld mine 4x or more
Ilang amperes ung lithium mo sir
80ah
pwede po ba yan sa battery ng pang cp
pang spot weld sa battery ng CP?
@@SolarMinerPH oo
pwede po
Boss pwede b gamitin jan ang 12v na adapter..wala kc ako battery
Hindi po pwede
@@SolarMinerPH ok boss..battery lang talaga pwede jan? Sayang nmn..
Pwede po ba yab i connect sab12v converter papunta sa 220ac
hindi
Pede kaya yung lead panghinang dyan
Pwede naman po. Mas ok lang ang spot weld dahil hindi iinit yun cells pag solder kasi umiinit yun cells at hindi maganda ang init sa lithium cells.
pwede sa 32650 na 40ah sir na subukan MO na
hindi ko pa po nasubukan pero I guess pwede sya
Pwede ba AC DC adaptopr 12v 1a?
no
@@SolarMinerPH how many ampere needed?
I don't know exactly how much amps you need dahil wala ako pang sukat ng surge current. Online sources say 40 to 400 amps. You can probably put a super capacitor in parallel para kahit 1A na power supply pwede. You just have to wait to charge the capacitors every spot weld.
pwede bayan sa power supply.
Hindi po
Pls update lods if matibay plan to buy ^^
Will give an update po soon. istress test ko po. titignan ko kung ilan weld kaya nya before masunog :)
@@SolarMinerPH salamat lods waiting for update ^^
tnx
Thanks lods..,
sir pwede ba ako magpacaptest sa iyo? hehe.
Pwede po sir.
how can i contact you sir?
@@cajolansang3231 you can join here facebook.com/groups/solarminers/?ref=share_group_link or find solarminer on fb
9:49 halos matabig ko yung kape ko! hahahaha!
Nakakagulat mag spot weld. Kahit ilang beses na ako nag sspot weld lagi parin ako nagugulat.
Nakakakuryente po b pg nahawakan yung handle?
@@cjhei8484 Hindi po
You will encounter board die if set to level 4 or 5. will on again after disconnect and reconnect + or - power
to overcome that seri 22 ohm resistor on diode M7
th-cam.com/video/1ZCbLdymJIs/w-d-xo.html