I run my saws rich during break in as well. Tend to run them a bit rich even after, more so while milling. Rich = more lubrication lower rpm and a cooler engine temp.
It really is sweet... I'm going to do a video tomorrow morning about the current pricing for Neo-tec and holzffarma... for a bunch of saws! There are some good deals out there right now for the holidays.
Was looking for a saw to replace my ms390 that has gotten undependable after a cylinder replacement, my ms290 has done great for at least 10 yrs but It bogs down in big rounds. I ordered a F380 off Amazon Monday anxiously awaiting it arrival. Thanks for helping me make up my mind, had planned to get a new ms391 glad I saw your review!
Got it for $315 with 24" bar and chain. Got a message from Farmmac that there will be 2 separate shipments one will arrive tomorrow, Thursday The other by next Thursday. Hope the sawhead comes first the ms390 will be short a 20" bar and chain for sure 🤗
That is awesome 👌 by far more affordable than oem... and they are great at service requests! If you have any issues, let me know, and I will help you resolve it! Iv had awesome 👌 luck with the 3 I have!
That's a killer price with bar and chain. Run it a little rich for the first few tanks. Most of the time, they come pretty rich! I would also run 32:1 or 40:1 tell break in! Then, whatever you like to mix! 😁 I run 40:1 most of the time! And 32:1 in My Milling Saws
Thanks for the break in tips. I'm located in central VA. Dad ran a timber company until his death in 91 he had a group of Homelite saws I kept for yrs. The f380 will be used for personal firewood. This will be my first use of a 24" bar, 20" bars have been my bar of choice. I tried a friends ms250 with a 18" bar recently 😉 not for me. Hope to share the arrival soon
I bought a FARMMAC F380 with a 28" bar, first it has some real compression, the first time I pulled the starter rope it jerked the handle right out of my hand. LOL Replaced that handle with the D handle ,Works better, and still have to sit it on the floor and put my foot i9n the saw handle to hold it down when I pull. Next ,with that 28" bar and chain it is quite a bit heavier than my 16" saws. I will be using this one only for the bigger logs,,anything the 16" saws have a hard time with..
You absolutely can run an 18. I run a 20in most of the time. It can even carry a 36in if you had to for a few cuts. www.amazon.com/3003-008-8917-Rollomatic-Laminated/dp/B005DBZVX2/ref=asc_df_B005DBZVX2/?tag=hyprod-20&linkCode=df0&hvadid=416788749780&hvpos=&hvnetw=g&hvrand=13012815071436192871&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9026211&hvtargid=pla-869781229622&psc=1&mcid=71b62168da6934e0b31e862f88fe414e&tag=&ref=&adgrpid=90729929941&hvpone=&hvptwo=&hvadid=416788749780&hvpos=&hvnetw=g&hvrand=13012815071436192871&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9026211&hvtargid=pla-869781229622&gclid=CjwKCAjw17qvBhBrEiwA1rU9w5LqxqjO2HdXNPxgCTvyxjRIRXagvIYYteyfjIGzt5Ty4OBbrx_bQRoCELkQAvD_BwE That's a link to an 18 ³/8 bar
Major…really like your channel! After watching your review of the Farmmac F380W I purchased one. I use this saw for cutting down/chainsaw milling oak, red cedar and standing dead ash trees on my property. So far I really like this saw. I have to mention one minor con about this saw, the air filter cover is misaligned about 3/8” to the left. I contacted the seller to get a replacement cover and received this reply…”F380W is cloned Stihl 038, so air filter cover misaligned, that is a special design. This design will not affect the use of the device”. What kind of BS answer is this. I believe in a review you indicated a similar problem and received a replacement cover. Who did you contact for replacement cover?
That is a very pore answer, I agree! I deal directly with a rep of neo... please, if you will send me a copy of your invoice through my email and I will contact them! We will get this resolved for you sir! Majorpixsaws@gmail.com
@Michael Schlosser hey 👋 have you spoken to Neo-tec about the issue? Seems like there was a Bach of the saws that come out with the holes drilled in the case wrong for the top covers! If you contact them, they would like to help correct the problem... the comment you saw from the other gentleman was resolved to his satisfaction after we spoke to Neo-tec about the wider spread problem! I can help assist you in this if you like, sir!
@@majorpixchannel7146 Yeah I'll try reaching out. An oem stihl is $13 on Amazon and has to be a sturdier plastic. Same time the carbon wrapping was bubbled/wrinkled out of the box so they should fix it. Either way I am still blown away at the over all quality and power of this saw. Oh yeah and then the price....$330 shipped with a 25" upgraded bar. The thing I hate trigger response and the type of plastic its made out of 🤢🤮🤮. My suspicion is there might be some corners cut in regard to quality in the trigger system.
So the dogs for the 060 fit most of the 0 series. 030, 380, 044, 440, 046,460 ext. The only difference is the roller on the bottom doesn't fit. There is 1mm difference between the inside dog and the clutch cover. Can't tell just by looking at it or running the saw. Not sure of the part number... However it the same as the 660. Most of these dogs will even fit the 311, 390, 310, 290 and many more
Thanks for watching sir! So Stihl recommends 12.5 k .... With having said that lol mine is heavily ported (I should do a video on that) and my go to saw out of about 75 saw collection lol mine runs at about 16k lol Now of course I don't run this saw all day at this rpm. It probably runs 2 to 3 hours at most. This saw is truly my favorite saw... And can out run a stock 660 both with 20in bars! Stay safe good sir! 💯😎👍
@@majorpixchannel7146 thank you so much for getting back to me with that information 👍🏼 I thought that it might be up in that range. Yours is a real ripper, thanks so much for the information, it helps me out a lot.
Yes... turn both low and high jet in all the way. Turn out one full turn. Start it up. Cut a few inches into a log. Put the screw driver into the high jet with the bar in the log (safer this way) and turn the high jet in small amounts tell you.like the power of the saw!!!
@@majorpixchannel7146 thanks for the tip. Also does the saw have any kinda way to decompress it when starting I almost tore my hand off trying to pull the rope to start it.?
@Stonercowboy69 yes sir... lol it takes some getting use to! Loads of Compression. So this saw is a clone of the stihl 038 magnum. They didn't come with decomp plugs the the 380
So the 380 has the walbro carb and upgraded crank and ignition system! The 380w has the hilic carb and standard parts! Both are supper nice saws! Iv ran both for extensive amounts of time, and they do wonderful!
Thanks alot. Just ordered a saw and was wondering what the carb replacement options were if I don’t like the Hilic. Looks like the different 038 models used either Bing, Zama,Tillotson and Walbro which make it all a bit confusing.
@@shannonwhitaker9630 correct 💯, depends on the year and model who Stihl was getting their carbs from. The hilic tunes well and holds up nice! I run about 10 saws regularly (daily) with the hilic! And out of a few hundred saws through my shop iv only seen a couple that needed switched out! Good odds for a Chinese carb! Thanks for watching
Bad quality or bad location? The one good thing about the front tenioner, is that it always works! Also easy to install for most people! However, lol using is BS as you say... I agree 💯
@@majorpixchannel7146 I prefer it in the middle like stihl it’s pretty inconvenient to try and get it on the side.. u gotta deal with hot muffler. And dogs.
It's truly my go to saw out of about 75 lol you will love it! The 380,440,460,660 all take the same spikes! And many other saws as well! Even the 311 and 39q
How did your search for West Coast dogs go? Did you find what you were looking for? We are going to start production on similar dogs! If interested... I looked through my comments to find you! Not trying to sell you just letting you know
Good question....it doesn't say on there site, I will ask a rep. I can tell you it feels strong... in comparison to the oem stihls I have there about the same! I will research and try and post back here Thanks for watching 👀
How does it compare to the farmtec g388?
Seems to be about the same to be honest
@@majorpixchannel7146 which would you recommend to buy?
I know this is old video.watching your videos has inspired me to buy this farmmac f380w saw.should have it tuesday.
It is a super good saw... I use mine almost daily! It's holding up very well!
I run my saws rich during break in as well. Tend to run them a bit rich even after, more so while milling. Rich = more lubrication lower rpm and a cooler engine temp.
Yes sir, absolutely 💯 correct!
Milling is super hard on a saw! Everything helps
Thanks for watching and commenting.. means a lot!
what are the differences to be aware of between the f380, f380w, ns872i? thanks
Thank you for this review, I have been waiting for it. I really want one of these
It really is sweet... I'm going to do a video tomorrow morning about the current pricing for Neo-tec and holzffarma... for a bunch of saws! There are some good deals out there right now for the holidays.
@@majorpixchannel7146 eBay is the cheapest I’ve seen $230 for the power head
@John Doe that's a excellent price 👌 😁
Was looking for a saw to replace my ms390 that has gotten undependable after a cylinder replacement, my ms290 has done great for at least 10 yrs but It bogs down in big rounds. I ordered a F380 off Amazon Monday anxiously awaiting it arrival. Thanks for helping me make up my mind, had planned to get a new ms391 glad I saw your review!
Got it for $315 with 24" bar and chain. Got a message from Farmmac that there will be 2 separate shipments one will arrive tomorrow, Thursday The other by next Thursday. Hope the sawhead comes first the ms390 will be short a 20" bar and chain for sure 🤗
That is awesome 👌 by far more affordable than oem... and they are great at service requests! If you have any issues, let me know, and I will help you resolve it! Iv had awesome 👌 luck with the 3 I have!
That's a killer price with bar and chain. Run it a little rich for the first few tanks. Most of the time, they come pretty rich!
I would also run 32:1 or 40:1 tell break in! Then, whatever you like to mix! 😁
I run 40:1 most of the time! And 32:1 in My Milling Saws
Thanks for the break in tips. I'm located in central VA. Dad ran a timber company until his death in 91 he had a group of Homelite saws I kept for yrs. The f380 will be used for personal firewood. This will be my first use of a 24" bar, 20" bars have been my bar of choice. I tried a friends ms250 with a 18" bar recently 😉 not for me. Hope to share the arrival soon
@Charles Hughes thanks for the update 🙏 that's so awesome... I know you will love it! Let me know when it shows up, brother !!
I bought a FARMMAC F380 with a 28" bar, first it has some real compression, the first time I pulled the starter rope it jerked the handle right out of my hand. LOL Replaced that handle with the D handle ,Works better, and still have to sit it on the floor and put my foot i9n the saw handle to hold it down when I pull. Next ,with that 28" bar and chain it is quite a bit heavier than my 16" saws. I will be using this one only for the bigger logs,,anything the 16" saws have a hard time with..
What do you think of noker saws looked alot like the saw from the video
Never had one in front of me, sir! These are supper awesome! Amazon has them on sale for like 220 if you are a prime member
I have a Farmmac 380w, can I put a 18" Stihl Bar and Chain on this saw? If so what model Stihl Bar. Thank You
You absolutely can run an 18. I run a 20in most of the time. It can even carry a 36in if you had to for a few cuts.
www.amazon.com/3003-008-8917-Rollomatic-Laminated/dp/B005DBZVX2/ref=asc_df_B005DBZVX2/?tag=hyprod-20&linkCode=df0&hvadid=416788749780&hvpos=&hvnetw=g&hvrand=13012815071436192871&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9026211&hvtargid=pla-869781229622&psc=1&mcid=71b62168da6934e0b31e862f88fe414e&tag=&ref=&adgrpid=90729929941&hvpone=&hvptwo=&hvadid=416788749780&hvpos=&hvnetw=g&hvrand=13012815071436192871&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9026211&hvtargid=pla-869781229622&gclid=CjwKCAjw17qvBhBrEiwA1rU9w5LqxqjO2HdXNPxgCTvyxjRIRXagvIYYteyfjIGzt5Ty4OBbrx_bQRoCELkQAvD_BwE
That's a link to an 18 ³/8 bar
Major…really like your channel!
After watching your review of the Farmmac F380W I purchased one. I use this saw for cutting down/chainsaw milling oak, red cedar and standing dead ash trees on my property. So far I really like this saw. I have to mention one minor con about this saw, the air filter cover is misaligned about 3/8” to the left. I contacted the seller to get a replacement cover and received this reply…”F380W is cloned Stihl 038, so air filter cover misaligned, that is a special design. This design will not affect the use of the device”. What kind of BS answer is this. I believe in a review you indicated a similar problem and received a replacement cover. Who did you contact for replacement cover?
That is a very pore answer, I agree!
I deal directly with a rep of neo... please, if you will send me a copy of your invoice through my email and I will contact them! We will get this resolved for you sir! Majorpixsaws@gmail.com
Thank you for your kind words, and I'm so glad you are enjoying the channel! It's really growing because of awesome subscribers like you 😁
Yeah the one I got the covers are so out of wack its not even funny. The instruction manual is absolutely harious though....if you know, you know.
@Michael Schlosser hey 👋 have you spoken to Neo-tec about the issue? Seems like there was a Bach of the saws that come out with the holes drilled in the case wrong for the top covers! If you contact them, they would like to help correct the problem... the comment you saw from the other gentleman was resolved to his satisfaction after we spoke to Neo-tec about the wider spread problem! I can help assist you in this if you like, sir!
@@majorpixchannel7146 Yeah I'll try reaching out. An oem stihl is $13 on Amazon and has to be a sturdier plastic. Same time the carbon wrapping was bubbled/wrinkled out of the box so they should fix it.
Either way I am still blown away at the over all quality and power of this saw. Oh yeah and then the price....$330 shipped with a 25" upgraded bar.
The thing I hate trigger response and the type of plastic its made out of 🤢🤮🤮. My suspicion is there might be some corners cut in regard to quality in the trigger system.
Part number on the dogs? I’ve talked to wsc and they say they don’t have anything for me
So the dogs for the 060 fit most of the 0 series. 030, 380, 044, 440, 046,460 ext. The only difference is the roller on the bottom doesn't fit. There is 1mm difference between the inside dog and the clutch cover. Can't tell just by looking at it or running the saw.
Not sure of the part number... However it the same as the 660.
Most of these dogs will even fit the 311, 390, 310, 290 and many more
She works well 👍🏼. I have the same chainsaw as well.
What is the maximum revs you take them up to?
Great video 👍🏼
Thanks for watching sir!
So Stihl recommends 12.5 k .... With having said that lol mine is heavily ported (I should do a video on that) and my go to saw out of about 75 saw collection lol mine runs at about 16k lol
Now of course I don't run this saw all day at this rpm. It probably runs 2 to 3 hours at most.
This saw is truly my favorite saw... And can out run a stock 660 both with 20in bars!
Stay safe good sir! 💯😎👍
@@majorpixchannel7146 thank you so much for getting back to me with that information 👍🏼 I thought that it might be up in that range. Yours is a real ripper, thanks so much for the information, it helps me out a lot.
@@Chucky-b7v anytime sir! Let me know if I can help in the future 🙏
I just got mine any tips on tuning the carburetor?
Yes... turn both low and high jet in all the way. Turn out one full turn. Start it up. Cut a few inches into a log. Put the screw driver into the high jet with the bar in the log (safer this way) and turn the high jet in small amounts tell you.like the power of the saw!!!
@@majorpixchannel7146 thanks for the tip. Also does the saw have any kinda way to decompress it when starting I almost tore my hand off trying to pull the rope to start it.?
@Stonercowboy69 yes sir... lol it takes some getting use to! Loads of Compression.
So this saw is a clone of the stihl 038 magnum. They didn't come with decomp plugs the the 380
Yo can you put a 32" bar on that thing?
@@Stonercowboy69 sure it will pull a 32. Id pick bigger saws to carry it full time. But, if you needed to pull a 32 it would have no issues doing it
Nice running saw Major!!
Thank you brother 🙏
Out of curiosity, what is the difference between the F380 and the F380W?
So the 380 has the walbro carb and upgraded crank and ignition system! The 380w has the hilic carb and standard parts! Both are supper nice saws! Iv ran both for extensive amounts of time, and they do wonderful!
Hello, can you tell me what Walbro carb is the replacement for the Hilic carb ?
@shannonwhitaker9630 1119-120-0605 OEM
This is the original OEM parts number
Thanks alot. Just ordered a saw and was wondering what the carb replacement options were if I don’t like the Hilic. Looks like the different 038 models used either Bing, Zama,Tillotson and Walbro which make it all a bit confusing.
@@shannonwhitaker9630 correct 💯, depends on the year and model who Stihl was getting their carbs from. The hilic tunes well and holds up nice! I run about 10 saws regularly (daily) with the hilic! And out of a few hundred saws through my shop iv only seen a couple that needed switched out! Good odds for a Chinese carb!
Thanks for watching
The tensioner sucks
Bad quality or bad location? The one good thing about the front tenioner, is that it always works! Also easy to install for most people! However, lol using is BS as you say... I agree 💯
@@majorpixchannel7146 I prefer it in the middle like stihl it’s pretty inconvenient to try and get it on the side.. u gotta deal with hot muffler. And dogs.
I just bought one of these what i’m looking for a pair of dogs from West Coast saw what style did you get to fit the chainsaw
It's truly my go to saw out of about 75 lol you will love it! The 380,440,460,660 all take the same spikes! And many other saws as well! Even the 311 and 39q
If you end up wanting to port it... I have a few easy tricks for the 380s
Thank you
How did your search for West Coast dogs go? Did you find what you were looking for?
We are going to start production on similar dogs! If interested... I looked through my comments to find you!
Not trying to sell you just letting you know
It was good they fit perfect yeah I would be interested in finding out that this 380 model ever made in the US not a lot of upgrades for this saw yet
Looks like it runs good!
Yes sirrr... it's a strong runner
Thanks for watching 👀 sir 🙏
What material is the handle/fuel tank made out of? Thanks
Good question....it doesn't say on there site, I will ask a rep.
I can tell you it feels strong... in comparison to the oem stihls I have there about the same!
I will research and try and post back here
Thanks for watching 👀
Still running good? Looks like you've had it a yes. Also do you think one is better than the other holzfforma vs neotec?
Love it
Thanks 😊 for watching 👀 🙏
Blurry vid Major
Clear on my phone... sometimes if the video is viewed quickly, it's kind of blurry for some reason. But it's clear now
Neotec makes quality saws with parts from all around the world. 🤘🏻🪓🌲
Yes sir... and are excellent when it comes to service requests