ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
BMW M54 Common Misfire’s,Rough Running & Vaccum Leak Symptoms Explained
ฝัง
- เผยแพร่เมื่อ 17 พ.ค. 2019
- in this video i will show you what to look for when looking for all your misfires and all your rough running symptoms on the M54 engine
most common codes for misfire is P0171 & P0174
Click here to buy Forte Injector Cleaner
amzn.to/2WQbR6b
Click here to buy the intake boot in my video
amzn.to/2WTwYnU
Click here to buy the T piece on the intake boot
amzn.to/2LOQD7l
Click here to buy Forte Injector Cleaner
amzn.to/2WQbR6b
Click here to buy the intake boot in my video
amzn.to/2WTwYnU
Click here to buy the T piece on the intake boot
amzn.to/2LOQD7l
Finally a gentleman who is very informed and and takes care to explain possible root causes and not just replace, replace, replace.
Well done!
sorry to tell you but e46 is literally replace replace replace regardless of what the issue is... especially if nothings done to the car by previous owner it all falls on you
@@e36fanatics You are dam right. I replaced my valve cover gasket just got it done the other day. 21 years old, I don't think it was ever changed. That rubber was burned onto the frame of where it sits. I had oil in the plug wells too. So far so good on that. Its running better, but the problem is not solved. I still have 2 misfire codes popping right back up. Nice that its running better though.
It helps if you do your own work when replacing parts because otherwise its would be a nightmare. Well, with a 21 year old car it already is a nightmare..........
Nice run down on the m54 rough idle faults still a good engine if maintained correctly I know some may disagree I never had any issues with my 330 apart from needing a new rad. Keep the great content coming dean 👍🏼
Love'em Dean Just changed oil had a whole 1,600 miles on it I don't get to drive it much. Need to do a Italian tune up on the highway. 👍
Have e60 m54b30 for a year now. First missfires were caused by ignition coils and spark plugs. Recently got P0 and lean codes. CCV has been changed twice in the past year. I hope the guy who will check this for me will find the issue.
Great job. 👍 also, the brake booster can cause a vacuum leak. If you hear a hissing sound from inside the car with the radio turned off and the car running it could be the brake booster.
I got a surge/stall issue, only on warm up from dead cold. No codes, only happens when in closed loop, looks rich, like it’s choking out. Smoked, no leaks. New ISC, CCV, CMP sensors. Will test the purge today.
I’ve got a M54B30 swap with some random misfires. This video helps a lot. It seems to be random.
Good thorough video on e46 all very very common problems.👍🏾
Knowledge is Power.
Thank you for a great tutorial.
your welcome
Having a rough idle only when the engine gets warm and up to temperature, it lasts about 20 seconds then smooths out, I did get SES light and showed misfire on all cylinders. 4 & 6 were changed. Still having this issue. Any help would be greatly appreciated.
I believe you you forgot to mention the mass air flow sensor. I had I misfire on cylinder 3 on cold star for as long I can remember and it was only on open loop until someone told me about the map sensor that they tend to go bad only when the engine is cold and he was right cause I change everything you mentioned on ur video and I was still getting cold star misfire until I replace the map sensor and now it runs like new .but thank you any way for ur information very helpful indeed
MAP is that the same as MAF?
Sorry, just googled MAP
Theirs a car (e46) at this auction near by do you think it would be a good buy if I get it for 300 bucks? It has check engine and can tell it’s misfiring let me know if should by and welcome the bmw to the family
Anxiety away through the roof
Will a scan tool identify this?
My e46 has a single cam engine
Very informative video all the same👍
I apologize guys I replaced almost everything on my 04 330ci, Hey Doc .the biggest issue I'm having now the brake lights stay on, oh and license plate light stays on constantly. I have taken and replaced fuse and the brake switch. The kicker is the left the switch out purposely . I replaced the 4 wire harness also. With the switch out the brake light still stayed on. Help please.
Thanks
John Crump
My e53 cranks but wont fully start the tempeture goes all the way to the right before even starting misfire on cylender 4,5,6 any solution ?
The part @ 5:30 of your video again please boss? I hear major air noise right from that area, and I don't ever remember hearing it like that. I already had to change the valve cover gasket (never changed in 21 years) due to oil in the plug wells. Its running better. I also ran and put in some STP waterI th remover and put in 100% pure gas (NO ETHANOL). Its running better than before, but the codes are back, and its still missing.....I think the part @5:30 where you start about it is a problem too.
my 2001 e46 320i, m54b22 engine it start fine no rough idle though when you hit about 5k rpm it tripps and start to serge and then the car cant seem to gain power like the rpms sputter and tell i shut the car off and back on and it fine. seems like it get fuel cut off at around 5k rpm
Hello, I have problems on cold start for a few seconds the idle is rough, and afterward everything is good i would say. All glow plugs are changed and the relay too. Can an oxygen sensor be faulty without reporting an DTC? What is the best way to test it, can it be cleaned maybe?
The car is E91 LCI 318D 105kw 11/09, it has only 1 oxygen sensor I would say only on the DPF, next to the temperature exhaust sensor and the pipe for pressure sensor.
Thank you for the answer in advance.
Did the bmw E39 2000 model come with a catalytic converter?
Is it effective rocker cover gasget issues to air leak
Good video mate. Keep it up. 😎
Cheers vladi mate trying to keep it up but I’m getting more haters then requested lol as you can see
I have a bank 2 , fuel range exceeded code and I have did everything to possibly finding a vacuum leak but come up short, with no results. What do you think it could be?
Iv got a e39 520 2.2 2003 and I'm getting fault code for cylinder 6 and cylinder 2 misfire with fuel cut off
Hi iv got a question I have a bmw e46 325i 2003 what the best make for ccv ? And what’s the easiest why to change it
Hi Dean, in one of your videos about PREVENTATIVE maintenance (M54) you say that you changed your vacume hoses for silicon and gave the id measurement, I have spent ages trying to find it with no luck, would you be kind enough to let me know the measurement of the id so I can buy the silicone tubing before I pull it apart. Grwat videos thank you.
I have a 95 325i with no start will crank but when tries to start it backfires bad through intake
Put a new intake manifold in as the old one had a hole in it on my m54 2.2 changed all the pipes and New Ccv system installed the car is throwing up codes p0300 p1349 p1345 p1351 what could this be in parts? Do you think it’s the DISA value or something else?
Hi bro I have a lil problem can you explain camshafts I’m in uk so I’m trying to get my sensors but I’m not sure about this one 2.41 DME: Signal, Camshaft Sensor, Inlet I’m trying to get it from eurocarparts and I’m baffled a bit I want to get camshaft position sensor and exhaust side I would like to change all sensors at once so can u please tell the best pronunciation off the sensors
First off al thx for your vids it has helpt qiet a bit :) i have a question i hope you can awnser my car is a e39 m54b25 2001 i have this issue thats bin bothering me for a long time, the car starts and runs fine on the low end but when it revs to 5k rpms it shuts of cyl 4 5 and 6 it ised to shit off only 5 and 6
I have read the codes and when is goed into limp i can reset the ecu and it wil run fine again , i have done vacuum test i have replaced coils and plugs also tested the o2 and switched to another one stil the problem remains i have switched the wire harnes of the coils for one i know is good ( I thought faulty wires) problem remains. Only option i think i have left are injectors or feul filter/pressure regulator ? Codes are p01349 p01351 p01353. I wil switch injectors with bank 1 to bank 2 to see if the problem goes to bank one then i know its injectors.
Greeting from holland keep up the vids 🤙🏼
Great video, could you please do a video on automatic transmission fluid change and any upgrade parts which are required for m54, I have seen many with failed safe trans message and loosing reverse gear.
Mate i won’t be doing M54 any longer it’s not good for my channel and most my viewers do not want it so I cannot do the videos for the few mate it doesn’t make me enough return on the videos
No worries how about general maintenance on auto transmission including modern cars as most GM are sealed for life. Any advice on when the fluid should be changed. Could you recommend me to a reputable transmission service center.
Tahir Iqbal I don’t ever reccomending it be changed I have my e60 on160k no change ever still runs perfect and smooth since day one
E46 159k gearbox still strong and sweet and pulls smooth as I always say it must be something on the USA where the gearboxes suffer from all that heat over there that breaks down your oil as here you hardly hear of that only on diesels and that’s ONLY when people remap them
Here we are not over the top like that servicing gearboxes and that there sealed for life sealed for life in my time of owning 100s of these cars I ain’t EVER changed the fluid and that’s been on cars with 270k with no history at all
hi mate I have e46 2003 convertible the windscreen is leaking fluid I've replaced the washers twice and its still leaking do u have any other suggestions
This m54 engine is plagued with oil and coolant leaks and misfires; not to mention badly designed piston rings. So glad I got rid of my 04 530i e60 for my ‘13 328i xDrive n26 SULEV F30.
Not to mention the weight of this engine puts A LOT OF STRESS on the front suspension.
You know what mate I completely agree and couldn’t agree more then I do I will be doing a video on that stay tuned and thanks for commenting mate
BMW Doctor oh wow thank you man that is awesome 😍😍😍 basically any BMW of the Chris bangle era is also the worst of the worst. Question who designed the f-series BMWs?
Some idiot designed it remmeber the leader of the m sport division left and went to Hyundai so bmw are clueless now
any idea why could my m54b25 e46 compact be runing sometimes badly, like it runs good, but then randomly it starts to change its rpm by itself, and even runing in 3rd gear, u press the gas it goes goes and then like shakes and lowers the rpm and then hits the rpm back to where it changed. Sometimes the car loses power out of nowhere and doesn't run like it should, and when pressing full pedal to the metal in 2nd, it doesnt accelerate fast as it should, but when that dissappears, it runs great and has full power again. I really dont know what to do, ive changed the spark plugs, the filters, checked vacuum leaks, changed the fuel filter, checked the air boot for some leaks, nothing, no error codes, only sometimes when it loses power it shows something w abs and traction control
my 1999 e46 starts ok but after a while it starts to misfire and i have to stop turn off and then on and continue driving, any ideas? the couls seems.to be good.
Hi mate I’m getting really rough idle, loss of power, engine light on and misfire in cylinder 3 and 4 with fuel cut off. Compression in the chambers is fine, have swapped plugs, coils and injectors around, cleaned and tested all injectors and still doing it. Any ideas? Thanks
Did you ever figure out what this was? I’m about to pull my manifold off and do ccv and all hoses, camshaft and crank position sensor.
Try the DISA Valve. The plastic that opens and closes can be broken.
Great video mate 👍, I'm sodding through a misfire problem on my 98' 535i 😢, can you recommend a cheap diagnostic set up for this car? I have the adaptor to fit it TO OBD2, there's so many available and a lot are useless. Any advice would be great mate, cheers 😀
I don’t really know any cheap scanners mate if I’m beeing honest lol as I don’t use cheap scanners the only thing I ever recommend with bmw is Ista because it gets the problem there and then without messing about and sending you around rings on the car like other scanners do and no other scanner can bring up electrical fault codes aswell as shadow codes
Anyone here had very rough idle and Missfire Cyliders 4,5,6?
Hey man, my e46 started shaking about 5 days ago just all of a sudden there in the morning. I took it to my mechanic he checked all the coil packs which were fine but my spark plugs were really wore and I only replaced that 3 months ago before this all happened. Then we put in fuel cleaner for the injectors as he thought maybe it was that and after that as I drove my engine light even went off and it was running all good but not even the next day it the light came back on and the shaking started again. It's still shaking pretty good and it's on and off so before I take it to bmw would you know maybe what that could be? Thank you so much if you could reply
What did it end up being? Check your valve cover gasket as one source of the problem. Very likely, its an vacuum problem somewhere. The design of these engines is like all dam vacuums sucking air all over the dam place. Its the most cumbersome engine system, but at the same time its well-built.
My e46 525i has a problem of behaving as if it's out of fuel when there's still more than half tank in it. But just when I top up gas..the performance is back to normal until I've moved the distance equivalent to the amount of fuel I've put it..my Guage also never goes below half..
What could be the problem?
Check the fuel sender on the gas tank under the back seat behind the driver side
I finally retired 330i today! Engine is perfect but rest car shit
Awesome vid man.
My m54b30 runs awesome, idles fine cold or hot, but when left idling for a couple of minutes it missfires... As if One cilinder is off and running in 5 only. Turn it off and black on, and its ok again... But only does this when left idling for more than a couple of minutes... If you are driving or reving just so slightly, it never fails... Any clue?
Thanks
Maf sensor mate camshaft sensors it’s can be many many things have you scanned it
I checked everything else it must be my o2 sensors
on idle my e46 runs super ruff . I unplug the maf and the car dies out like normal. Turn it back on with maf unconnected and runs perfect. Any idea ? Throwing both p0171 p0174
Either vac leak or some of your electrical components are going bad, i had the same issue. what codes are you getting.. other than the lean codes??
I have rough idle, loss of power, lower mpg, Code P0174 on bank 2 only... Any suggestions? So any of this can cause the only code P0174 bank 2?
Should be a vacuum leaks. Am dealing with those same codes
Where are you based? I have rough idle issue on start I’ve changed spark plugs, injectors no luck also the car feels slow to drive Bmw e39 525i
I’m based everywhere as I do everything remotely so I can fix your rough idle no matter where you are just have a laptop that’s all you need
BMW Doctor I have a laptop
How would you diagnose p0420
old cats dead, buy new ones!! Solved! Expensive but necessary
Would you mind helping me diag mine? :D
So, basically it could be 50 different problems. Not your fault just the way these cars are.
What could that be
hi, can u speak slower and more clear please as your films are ok but u talking to quickly and to many things at once..