great reference vid, love me some 77. A little trick when case matching... Instead of using a marker, cover the face with blue painters tape, then with your gasket and exacto, cut out the tape where you are removing material. It makes a much sharper line, and when your bit hits the tape, it will fluff up a little and you can clearly see you are at your edge.
I used porting wax for my carbide cutters keep them clean you don't lose your indication mark like W40 can wash it away.... WD40 on the stones keeps them clean
I think the direction of the seal on the main gear is wrong. the green side should be on the outside, sealing it off and keeping the dirt out. I never saw one puch maxi moped with the seal on the main gear installed in the way this video shows. And doesn't the brass spacers get stuck due to the heat? That's so far the only notice. I believe the rest is all done in the correct way.
No. That is how they come from the factory. .......but these are dual spring seals so it shouldn't matter. I put 8 of those brass spacers on and it did get stuck, I got it off with a rubber mallet. The MLM SPACE SAVER studs are awesome on a Polini but they are too wide for a Gila :).
@1977mopeds I use same method to fit main bearings but the pro's say to use a device to push them on. also its good to match the transfer part of cases so that they line up with crank webs so that there is a smooth passage if that makes sense?
Hi there... I have a puch maxi and the bearings just failed so I'm hopefully am going to rebuild the motor... How much money (dollars) is it to get new seals and bearings for the whole e50 motor
reeed valve but only 4 transfers, why not have boost ports above reed valve? and the tiny holes in the piston to feed crank case, could be bigger or cut a slot down cylinder? Interesting little engine though.
@maxmojo2 ops.. ha-hem :-) Gilardoni makes only cylinders .. Btw, i like this old 2 strokes engines, even if is austrian ahah and the international passion for mechanic and music.
Beautiful porting. I did mine today after seeing this video, it's not so tidy, but have another 4 engines to practice the art on.
great reference vid, love me some 77. A little trick when case matching... Instead of using a marker, cover the face with blue painters tape, then with your gasket and exacto, cut out the tape where you are removing material. It makes a much sharper line, and when your bit hits the tape, it will fluff up a little and you can clearly see you are at your edge.
❤ love the music with it. Made it so easy to watch
Great video for an old good italian engine.
What a superb video. Nice work.
Very wel done, ancwered lots of questions. And was abe to show 'helpers' how to assist me. :-)
This is pure art
I used porting wax for my carbide cutters keep them clean you don't lose your indication mark like W40 can wash it away.... WD40 on the stones keeps them clean
Thanks for the info.I really enjoy your videos.
Sure do. Check out our WSL pipe, and some of the kits we offer.
@pacetanner We will be doing more in the future. Motobecane is on the list! Thanks for the support!
I think the direction of the seal on the main gear is wrong. the green side should be on the outside, sealing it off and keeping the dirt out. I never saw one puch maxi moped with the seal on the main gear installed in the way this video shows. And doesn't the brass spacers get stuck due to the heat? That's so far the only notice. I believe the rest is all done in the correct way.
No. That is how they come from the factory. .......but these are dual spring seals so it shouldn't matter. I put 8 of those brass spacers on and it did get stuck, I got it off with a rubber mallet. The MLM SPACE SAVER studs are awesome on a Polini but they are too wide for a Gila :).
@1977mopeds
I use same method to fit main bearings but the pro's say to use a device to push them on.
also its good to match the transfer part of cases so that they line up with crank webs so that there is a smooth passage if that makes sense?
how do you close that hole you make in the port of the case?
bel lavoro !! ai miei tempi solo modifiche sui pezzi originali....aparte gli ultimi periodi dal 1983 in avanti che sono arrivati i Malossi 65cc ;-)
Hi there... I have a puch maxi and the bearings just failed so I'm hopefully am going to rebuild the motor... How much money (dollars) is it to get new seals and bearings for the whole e50 motor
Спасибо! Очень хорошее видео!
reeed valve but only 4 transfers, why not have boost ports above reed valve?
and the tiny holes in the piston to feed crank case, could be bigger or cut a slot down cylinder?
Interesting little engine though.
how did you "flat out" the weldings?
@wildwespocketbike They are on order with Italkit. Just waiting for them to come in.
Dan
clean work. i go way bigger on those!
Looks good! :)
got any great videos on tuning the m48 as used in the ariel 3 and batavus bikes?
This is a good video!
@maxmojo2 ops.. ha-hem :-)
Gilardoni makes only cylinders .. Btw, i like this old 2 strokes engines, even if is austrian ahah and the international passion for mechanic and music.
?? is the cylinderhead turnd 90 degre ??
from where you have these bushes on the stud
Then what should you use?
cool video I am building an av7 any chance you guys will be doing a video of one of these? ps i got my kit from you!
is there any chanse on doing a tomos a35 engine?
i wanted you guys to do the welding and bore i was not going to send my case to someone that not answser
what happens if I don't grind the case?
now start doing this kind of videos with all kinds of zündapp and kreidler engines!
When i were you i shouldn't polish the portings. When you don't you'll get a better flow
What clutch is tht? Would you recommend tht clutch on a 70cc kstar build e50?
Hey dudes,I just subscribed. Im a collector and just bought two 1982 honda urban express deluxe nu50m.you got after market parts for those?
No polishing?? Still seems rough. Missing the first startup in the vid!? :-(
plz do this on Kreidler engines, much more HP with SB cilinders
Schönes Video aber paar Fehler und fragwürdige Entscheidungen beim Zusammenbau...
PS.: viel Glück mit der Kurbelwelle bei dem Zylinder xD
is it necessary to weld the case @1977mopeds?
If you are installing a Gila, or a Metrakit, yes.
Ok, thanks for the info!
Do you add material to the case? I thought gila e50s needed material added?
Is porting necessary? Or no
nice
@ECSuspect Great tip!
Leave a message, and we will give you call back. Thanks!
More info on welding the case? Materials etc.
think this will work on a jawa 207
how much does this cost?
230 for the kit about 100 $ to bore and welding cases without shipping to and from. Likely 450ish.
eu precisava da fiacao
@nicodanger13 AUSTRIAN* Engine.
I am not sure if we got the message. Call 1.888.743.1977, I would love to hear from you.
This video missed the most needed to be seen step of boring the case to fit the wider jug.
Mike S ....a flap wheel dremel or drill bit works well.
This video changed my life 😳 delete that meaningless crap
This ist tuning and nothing else
i got your email i call but no answer:0(
Your seal ring in the back is in the rong way
No in the manual picture it is mounted this way
Why😰😭😂
2 Strokes -- Yes.
Mopeds -- No.