2021+ Ford F-150/Raptor Dash Mount PRO Install Guide // BuiltRight Industries

This guide demonstrates the step-by-step installation of the BuiltRight Industries Dash mount PRO for the 2021+ Ford F-150 and Raptor. Expect this install to take 30-60min using the tools listed below.
Product Info: builtrightind.com/products/da...
Non-PRO Installation Guide: • 2021+ Ford F-150/Rapto...
Tools Needed:
- 1/8in Allen Wrench
- 7mm Socket and Ratchet
- 3/8in Socket or Wrench
- 1/8in Drill Bit
- 3/8in Drill Bit
- Plastic trim tools (optional)

[@aegiscanada]

This has to be one of the most thorough how-to's for a product. Mine has arrived so I'll be tackling it soon.

[@kendjay2]

Thanks for the video, just finished installing.

[@Mikp-zw3cs]

Just to be a little more helpful on this install, they did not add the support plate, I would recommend getting it and also buying a set of transfer screw set, ASE standard, then mount the plate and put the transfers in place put your cover back in place and snap it in, this will mark the locations on the cover you need to drill, leave the plate in place and then when drilled put your cover back on and snap it down and add your mounts to the dash mount kit before you screw it down, also use blue lock tite on the screws.

[@USAF-SF]

I love ya brother, and I love your products, Lord knows I own plenty of them... But you need to give me some MOPAR love for my 2014 PowerWagon and come up with a kick-ass dash mount that is clean and sweet. Big props to you for all the other products that have come from your shop, awesome!!!

[@BuiltRightInd]

Appreciate the support and feedback! We've got a wish list a mile long - RAM dash mounts are on it. Thank you for the feedback - that's what makes new products happen!

[@HKChad]

Got mine this week and installed would have been REALLY nice if the mounting slots lined up with the screws that hold it down (not sure if the AMPS version would fix this?), even with oversized hole and rounded allen getting those screws installed took the longest of any step due to the angle. I will say, it's solid!

[@BuiltRightInd]

Thank you for the feedback! The challenge that you describe is resolved in the new revision!

[@MaximusWilliams]

Ditto

[@hobbinshaw]

I had same issue with mine (just got and installed it today). Otherwise it’s solid

[@matttrotta57]

Looks like the pro bracket i got is shaped different. I not done yet but looks like the nibs are not 9n the way with new version.

[@glennwallace9203]

I came here just to post the same thing. Keep the nibs!!!!

[@blaisemeadows4766]

My 2022 only has 1 silver radio mount bolt on the passenger side, not sure how to attach

[@daveharness70]

Did you ever get things figured out or get a reply?

[@michaelmitchell4200]

I have a 2022 as well - were you able to get this resolved? I'd like to use the PRO as long as it's compatible.

[@daveharness70]

@@michaelmitchell4200 I'm likely going to install my pro version this weekend. I'll reply here when I get it done.

[@michaelmitchell4200]

@@daveharness70 I went ahead and purchased the PRO and installed mine today. I had both silver radio screws on my 2022 XLT. No issues with the install. I ended up drilling my holes slightly larger to ensure proper alignment of the mount.

[@daveharness70]

@@michaelmitchell4200 I finally got around to installing mine yesterday. The pro-mount is different that the one shown on the install video. I had the "nubs" on my dash piece but didn't have to remove them to get it to fit, which was nice. I also didn't trim any plastic ribs on the sides...just the one in the center. I was pleasantly surprised at how easily it installed Perhaps I missed the "redesign" of the pro bracket announcement. Did they do an update install video on that? I'm sure they have a long list of things to do and have been working hard getting the kinks out of the new facility.
I installed 3 mount balls, 2 for the ram phone mounts I purchased with the mount board, and another ball from a previous Tackform mount that I will be using for either my tablet or a camera.