How to Install | Auber PID w/ pre-infusion Kit Installation | Rancilio Silvia Espresso Machine
ฝัง
- เผยแพร่เมื่อ 18 ต.ค. 2024
- Rancilio Silvia PID - new.seattlecof...
Please visit www.notneutral... 15% Discount Code - "HOONSCOFFEE"
Rancilio Shower Screen Upgrade Kit - amzn.to/3tKbeM2
Coffee Scale - amzn.to/2HlbQ75
Knock Box - amzn.to/356YPXh
Fellow Atmos Coffee Canister - amzn.to/2Oc87ZY
Follow me on
Instagram / hoonscoffeeaz
As an Amazon Associate I earn from qualifying purchases.
I'm very late to the party here, but thanks for this video Hoon! I received my machine today with a PID installed, but it went haywire on me tripping the boiler safety and everything. Your video showed me how easy it was to get at the wires screwed into the back of the PID controller. I found one crossed wire and one loose screw and my machine works now!
At least you were honest Hoon telling people to buy the machine with the PID built in.
First class video and description.
Kind regards from Scotland
Johnny
Just installed the Auber PID on my twelve year old Silva. This will eliminate the temperature surfing I had to “master” over the years of brewing shots. Installation was not an issue after reading the instructions and watching your video (thank you!). After that, went step by step and took my time to do it right the first time. From start to finish, took me about 2.5 hours. As for the end result, very slight improvement on what I have mastered over the years. At least now I have a solid temperature on which to improve my shot. Next step, pressure gauge to check and adjust the pressure to really dial it in.
I am about to buy a PID with pre-infusion and your video is so clear that I'm ordering today (finally confident to install it and upgrade my V2 that has been upgraded in V3/V4 in the last years). I hope it will both upgrade and solve my brew thermostat problem (because it needs to be changed anyway).
Your video is super clear, just don't forget that if your camera has problems focusing, it's because your lens is to close to the subject. Move back a bit and the minimal distance will make it easier for the camera to focus.
Thanks again!
Thanks for the video. I just got my rancilio for $450 on an auction. The ones with PID already installed run over 1k so purchasing it separately saves me a lot of money so thank you for this step by step because I’m a visual learner. Can’t wait to get it and install my self :)
Hoon superb video. Clear and concise. I agree with what you said, your video will make it all makes sense after reading the manual. I will now look to buy and DIY this PID for my 8 year old Silvia. Improvement is continuous. Once again, thank you Sir.
In Australia the PID including install costs $559 AUD. It's better to install it yourself and save $$230 AUD
Just did mine. A bit more work with the E version (auto shut off after 30 min). The power controller at the back needs to be relocated to make room for the SSR and the power wiring connects to the brew switch instead of the power switch. Otherwise ok to install. I out the controller a little too close to the brew head and it’s now stuck. Fingers crossed won’t get too hot.
Just installed one on my v6 with a little help from your video! Thanks a lot!
Great video, thanks! I've been considering one for my "vintage" Coffee Gaggia, which is still working great after 11 years, and still has all the parts available to keep it going another 10 at least! Based on your experience I think I can handle the installation. (And just btw - it looks like the PID version of the Silvia you linked to is $1099, but the non-PID at SCG is only $735.)
Thanks for the video. I am looking at installing a PID on my Silvia as well. Do you know if there is a way to maintain the function on the brew button?
The LE black looks sharp with that PID! Great job.
After doing this almost all the way through: Start with the last step connecting the cables to the PID. Its very fiddly when the cables are connected to the rest of the machine. Remove the front plate and there will be plenty of space to thread the connector through to the rest of the machine.
Just scored an awesome deal for a v3 silvia on ebay, super excited! Immediately started researching pid kits lol
Hi Hoon, great video. Very educational. Thanks for showing the whole process.
You mentioned that the price difference is $100. but that is not the case. Black colored Silvia is for $795 where as the Black with PID is $1,159. So the difference is $364 (1159 - 795). For stainless steel, the price difference is $364 too (1099 - 735). The black color adds $60 to the machine.
But the amount of time, effort and headache this seems to take, I think with PID it is worth it. You did mention that 2 computer techs spent 2 hours on it. And of course, this is as first timers. And yes, it also voids the warranty. So thanks again for making this video.
You didn't take into account the cost of buying the PID, which is $200, so roughly around $100 give or take what current offerings are.
I notice you tap the power switch for power, rather than the brew switch as the Auber guide advises to. Have you encountered any issues related to this since carrying out the installation? Thanks
Greetings! And thank you for the video on installing Auber PID in a Silvia. I’ve used a version 1 Silvia daily for 17 years and love my machine. I’m now in the planning stages to add PID to my Silvia and would appreciate your opinion. I’m not that interested in pre-infusion but willing to purchase the kit with pre-infusion for the benefit of the steam control. Do you find that controlling the steam with PID is beneficial? Also, can the pre-infusion be turned off (disabled) or set to 0 seconds to circumvent it’s use? Thanks for your consideration!
Good job Hoon, hope it will enable you to make great shots every time.
Can you do a longer pre infusion than 2.5 seconds? Lance did a dimmer mod on the motor. Would that work with this PID mod? I bought my Silvia in 2003. Still going strong. So I am not worried about the warranty.
Thank you for the video. I also work with computers on the hardware and software level, but I agree. I would rather pay the extra $100.00 and have it already installed for me, and not voiding the warranty.
Thanks for this video. I was on the fence about installing myself. I think now I'm going to leave it to the pros. I was curious though, how easy/difficult you think it would be to remove the PID and return the Silvia back to factory settings at some later point.
Removing is pretty easy at this point.
Hopefully, I'll get answers here. just a question, does the brew button needs to be pressed from the PID. What if i still want the brew button from the machine itself to work?
I only have two total output cables which the guide tells me to connect to the brew side. My PID kit leaves the steam settings alone then?
I recently installed the PID w/Pre infusion on my v5 Silvia M and noticed that the pre infusion actually activates the 3 way solenoid valve which disrupts the puck.
Great clear explanation. Well done!
That’s good advice, for 100$, I would get it with PID
Thanks for the video, really good description of the install,
*shows how easy it is* “Don’t do this, it’s a headache”
Yeah, I just did it myself and it was a major pain in the ass. Cut my finger pretty bad on one of the sharp edges. But pretty satisfying to have done it. It is just really expensive to buy one of these with PID installed. I think it was $1,000 plus on Seattle Coffee. For that price, you might as well go with a heat exchanger machine.
May I offer an alternative view to getting a Silvia with PID pre-installed?
From my recent experience, Silvia PID conversion vendors seem to be a small cottage industry of techs working out of their garage. When I was looking, the issue for me was time, not money. I searched high and low, but could not find anyone with a PID'd version ready to ship... Plus, the few that responded to my inquiry showed little enthusiasm. None would commit to when, or if, they might be willing to make one for me. As a result, I decided to DIY it... hey, after all, this is only a hobby. Granted, there's some hassle involved, you feel like you might fail, but in the end, you discover that the task was easy and you learn a lot. Plus, as a hobbyist, the end-user personal satisfaction 'at-a-boy (girl)' experience is top-notch. Try it... surprise yourself. I bet you can do it.
Well worth the effort... M
thank you for the comment. What is your setup at home?
@@HoonsCoffee My basic kit: Rancilio Silvia V6 with included accessories, 15 yo new bought Mazzer Mini grinder, an RS V1 naked porta-filter holder, 18g VST ridgeless pf basket, flat screw infusion screen (www.pidsilvia.com), 58.5mm tamper, 58mm MATOW dosing funnel, MATOW espresso mini-whisk, modified 3-in-1 Key Cap puller. Vivace (Seattle) single-origin, fresh roasted, beans, + 5-10 days beyond the roast date.
Great video
What is price difference installing as add-on versus buying with already on machine?
He said a hundred bucks in the video.
Only $100
Where are the silvia PID videos ?
Hey hoon, any option got pressure gauge for silvia?
Not really unless you want to modify the case.
To complicated for me 🤣 I'd just get it professionally installed or buy a machine with PID. Nice job though 👍
Do you or someone knows a way to get only a cable set? I want to source the rest by myself.
Have you reach out to Auber?
it's crazy that you didn't peel the protective film on your silvia but somehow the screw holder things are rusty. Do your peeeeeel
you cant buy a rancilio silva with PID
seattlecoffeegear has one option