My job just slowed down all our machines to go 3.5 miles and hour instead of the 5.5 now we moving like turtles I just tried this out before I left tonight and it worked 😂😂😂😂 ima be zooming past everyone tomorrow Lmfaoo
My job just got a new RR 5700, lovin' it! However, it's a little bit slower than our old one (both single reach trucks), and goin through the performance tunes didn't do anything. Working overnight, it would be nice to have it at the same speed. Any tips? Also, you have to hold the raise cutout overide to turn the reach on. The old one you don't. Im sure it a safty thing. I'm just curious if there's a bypass or somethin
Once I put in the service code (2311) and went in to the settings and made the changes it worked! The "factory" performance tunes didn't seem to change anything.
Hi is there anyway to adjust the speed at higher levels? when at lower height the speed is fine but when we go up on a higher height it limits itself to 1.0 speed. thanks!
Please set potentiometer. Take 13 mm spanner, loose that pot1. Turn by body slightly. And check handle calibration menu. Set on 49 to 54 at centre. Than calibrate and save. Tight that pot1. Now ready to use. This will solve your fluctuate speed during drive problem.
So the p3 was for going forward? But what I don't understand why one day the op works fine connecting to wire guide and sometimes is just go beeping and won't connect it does but it goes really slow
to assign a speed to p1/p2 etc, do you do this while in that profile? or can you set all the profiles from that same menu? We have a casepick section we'd like to keep slow, but our overstock/bulk to run max speed
@paulaloper689 hello I might have already replied to you but if not ff, = forks first / reverse, and tf = tractor first . Let me know if this helps and thanks
que tal amigo buen día¡¡ una pregunta tengo un montacargas Crown eléctrico se daño la tarjeta de distribución ya conseguío una nueva pero se instalo y el montacargas no la detecta . sabes si necesita algún tipo de programación ?
Hello Jon! Does this guide work for the 4500 series as well? I tried searching for it on the company website but with no luck manual thanks in advance!
Hey Riceball - What year is your picker? also you should be able to set it on up to 5.5 or 6.0 . if the picker has height switches it will only travel at 1.5 all the way up and cut out if you turn the wheel.. but you are trying to go faster at the 24 inch switch? Go back into setting and turn the speed all the way up and try that. after you test the picker let me know what it went to for example a raymond picker will go to 7.5 MPH top speed..
Unfortunately the crown Access OP will / should have 2 DC lift motors / pumps that has a 2 speed switch on the platform , let me know if it has an AC lift motor.
Hi Ken, The only way you can change this back to 2311 is to have a CROWN service tech hook it up to a laptop. Try 2220 if that's not it then you will need to call CROWN. What state are you in?
@@jondoe3639 Tennessee,all of our lifts have been turned down to 5 mph and they are sit downs so if u have any seat time u know this is miserable lol ,we have a new safety man and I guess he is try to prove his worth or something ,I work the night shift so we have more freedom to change the speed and change it back for the suits lol ,thanks for reaching out if u have any more info please share
@@2a_day958 im afraid not. The op is a dule pump 24v and only 1 speed , if you had a 36v with a ac motor would be better but unfortunately thats all she has ..
When you hit the lift do you hear or see both motors going? If not you might have a bad switch or lift motor but more than likely it would be a switch.
Unfortunately the crown Access OP will / should have 2 DC lift motors / pumps that has a 2 speed switch on the platform , let me know if it has an AC lift motor.
![[LIVE] : ONE ลุมพินี 76 | คู่เอก "ผึ้งหลวง vs สมิงดำ"](http://i.ytimg.com/vi/9SBshmGQOIM/mqdefault.jpg)
My job just slowed down all our machines to go 3.5 miles and hour instead of the 5.5 now we moving like turtles I just tried this out before I left tonight and it worked 😂😂😂😂 ima be zooming past everyone tomorrow Lmfaoo
Just what I needed, thanks
Good deal.
Thanks for this video just what I needed
Thanks! Now it doesnt take my machine 5 business days to drive from one end of the wherehouse to the other lol
Im about to get un trouble at work because of this thx hah
Just be mindful when adjusted the speed.
Gracias maestro me ha servido mucho .
My job just got a new RR 5700, lovin' it! However, it's a little bit slower than our old one (both single reach trucks), and goin through the performance tunes didn't do anything. Working overnight, it would be nice to have it at the same speed. Any tips?
Also, you have to hold the raise cutout overide to turn the reach on. The old one you don't. Im sure it a safty thing. I'm just curious if there's a bypass or somethin
@ashtonpatton6583 good morning, the hold the raise and have to hit the over ride is a safety. The truck would have to be flashed by the dealer/ crown.
@ashtonpatton6583 ( also the speed settings didn't change the speed of travel?
Once I put in the service code (2311) and went in to the settings and made the changes it worked! The "factory" performance tunes didn't seem to change anything.
Como agregarla a p3
Thanks mate that helped 😊
No problem 👍
Hi is there anyway to adjust the speed at higher levels? when at lower height the speed is fine but when we go up on a higher height it limits itself to 1.0 speed. thanks!
That's a safety
It's a safety cut off, no you dont need to go 7 mph with forks 2 stories high.
I use this to slow down problem operators (18-25 Age) or to make sure no one messes with or uses MY ASSIGNED MACHINE
Hope it was what you needed.
@@logantrisilla6579 it's not that i am a know it it all, i am a forklift tech lol. let me know know if i can help you with anything else.
@@jondoe3639 I was talking to the other commentor, not you sir. You are helpful
Please set potentiometer. Take 13 mm spanner, loose that pot1. Turn by body slightly. And check handle calibration menu. Set on 49 to 54 at centre. Than calibrate and save. Tight that pot1. Now ready to use. This will solve your fluctuate speed during drive problem.
ive done this and maxed out the settings but the pe4500 doesnt go and the bunny button doesnt work either
Muy buena guía
Gracias
Besides code 2311, are there any other codes other than..?
You see, I operate RR 5700 singgle deep.
Yes
Try 2220
@@jondoe3639 Ok bro I will try it, with code 2220 and hopefully the same.. 👍🏻
Thanks
So the p3 was for going forward? But what I don't understand why one day the op works fine connecting to wire guide and sometimes is just go beeping and won't connect it does but it goes really slow
to assign a speed to p1/p2 etc, do you do this while in that profile? or can you set all the profiles from that same menu? We have a casepick section we'd like to keep slow, but our overstock/bulk to run max speed
What's the difference?
You should be able to set each unit specifically for each one in the menu of each truck
How do I reset it back to how it was?
Go back through the steps and set it to what it was . More than likely it was maxed out from the factory
Do you know the code to make the top speed higher?
What speed is it set at ? 7.5? and make sure it's the TF NOT FF.
@@jondoe3639What does TF and FF mean?
@@JoshuanPaula4Ever1 tf is tractor forward and ff forks first, fo tf, = forward and ff, = Reverse
@paulaloper689 hello I might have already replied to you but if not ff, = forks first / reverse, and tf = tractor first . Let me know if this helps and thanks
TF = Tractor first and FF = Forks first.
que tal amigo buen día¡¡ una pregunta tengo un montacargas Crown eléctrico se daño la tarjeta de distribución ya conseguío una nueva pero se instalo y el montacargas no la detecta . sabes si necesita algún tipo de programación ?
What dose it do when you plug it in? will it light up?
sorry for the delay i have been out of town.
thank you for you information ,i need the manual of sc5300 .i have error 300.110.126. and 124.thanks
Sorry i don't have a manual for that but check forward and rev switches. sorry it took so long to get back to you i have a lot going on.
I try and change something and it says re-key. No clue what that means but it wont let me move out of that menu.
Re key means turn it off and back on
Sadly doesn’t work on the Crown RT4020
I am facing with raise Switch problem. How to solve this. Need your kind advise please.
Do you know witch switch 24 ? Or what make and model is it ?
Just wondering if you know how to change from p1 to p2 or p3
Lift is 1 speed unless you have 2 DC motors then you will go a little faster.
Hello Jon! Does this guide work for the 4500 series as well? I tried searching for it on the company website but with no luck manual thanks in advance!
Yes it should work unless someone changed the 2311 code.
I just got sacked 😂 Worth it though 👍🏻
@@LuciusDriftwood you work in Houston by chance?
@@TheAndreaLGaines No. England.
I do not work in Houston.
Is the code the same for the pe4500’s?
Should be, if not you can try 2220
Do you know how to change the speed when the picker is guided on the wire? I tried to change it to 4.5 and it’s still slow
Hey Riceball - What year is your picker? also you should be able to set it on up to 5.5 or 6.0 . if the picker has height switches it will only travel at 1.5 all the way up and cut out if you turn the wheel.. but you are trying to go faster at the 24 inch switch? Go back into setting and turn the speed all the way up and try that. after you test the picker let me know what it went to for example a raymond picker will go to 7.5 MPH top speed..
Those units are not for speed. The equip of the technology is purely for maintenance and diagnostic purposes
If on a wire it will travel around 1.5 that's a safety
How about going up fast?
Unfortunately the crown Access OP will / should have 2 DC lift motors / pumps that has a 2 speed switch on the platform , let me know if it has an AC lift motor.
Hey Jon doe they have changed our 2311 pin do you know how to change it back or erase it or any way we can get past it
Hi Ken,
The only way you can change this back to 2311 is to have a CROWN service tech hook it up to a laptop. Try 2220 if that's not it then you will need to call CROWN. What state are you in?
@@jondoe3639 Tennessee,all of our lifts have been turned down to 5 mph and they are sit downs so if u have any seat time u know this is miserable lol ,we have a new safety man and I guess he is try to prove his worth or something ,I work the night shift so we have more freedom to change the speed and change it back for the suits lol ,thanks for reaching out if u have any more info please share
@@2fast4you423 ok will do. If you have any other questions feel free . Thanks
@@jondoe3639Massachusetts
Wat the service code it not 2311 anymore please share
yes do you know the code for me to configure the esr 5200 crown machine?

did you try 2311?
On crowm acces 123 services code is not 2311 r there a different code besides 2311
Do you know if you can change the raise/lower speed?
Do you have a access crown? with 2 DC motors ?
@@jondoe3639 yeah
@@2a_day958 im afraid not. The op is a dule pump 24v and only 1 speed , if you had a 36v with a ac motor would be better but unfortunately thats all she has ..
When you hit the lift do you hear or see both motors going? If not you might have a bad switch or lift motor but more than likely it would be a switch.
@@2a_day958 let me know if I can help with anything else.
When I press p1.2 it doesn’t let me go pass 1 and 2?!?
What are you working on ? Model
Hey man do you know the code for the tugger too?🙏🏾
Hey sorry been working crazy hours, try 2220 let me if that works thanks.
@@jondoe3639that didn’t work
That work ?
@@jondoe3639 no 2220 didn’t work for the tugger. But thanks though
@@jondoe3639nah it doesn’t work idk why
Hi , do you know how to turn on Xpress lower ?
Hi sorry i have been out and about... Xpress lower. Can you send me the model and serial # ? I will check into it and let you know..
@@jondoe3639 no worries man, im lucky you even responded haha, its an RM 6000
@@jondoe3639 im asking because at my warehouse, some forks have it and others dont
@@jondoe3639 serial : 1A610180
Is it the Mono mast?
Esr 5200 code service ?
Hey you need help?
yes do you know the code for me to configure the esr 5200 crown machine?

That not service code 2311 do anybody know the service code please share
Try 2220
Elevation speed?????
Unfortunately the crown Access OP will / should have 2 DC lift motors / pumps that has a 2 speed switch on the platform , let me know if it has an AC lift motor.
Y el código de la 3500 4000
Si
My shitty warehouse turned the speed down to 3.5 saying it’s for safety
If its a small space then just be mindful..
What the password nivel 2 ?
2311
Slow down. And the background noise is to much.
So sorry , i would pause it as many times as you need..
Thanks
Welcome