used EPS (electronic power steering) flashing and coding with Esys on bmw F30 ... vehicle test before and after with Ista ... solution of fault code no current coding data stored
Ok after thinking and looking in the codes i found what i need and i programmed succesfully thank you sir !!!! Thanks to your video now i have coded EPS🎉🎉🎉🎉🎉
@@heshamessam8042 hi, sorry for asking for more information. I flashed the ecu but not all, then today I went back to connect to flash the rest of the ecu but it doesn't allow me to do full flash anymore, it gives me not available on i-step Target and shipping, what's wrong?
When im doing the calculation for the TAL file appear a message telling me 3 TAL LINES HAVE BEEN SENT TO STATUS "NOT EXECUTABLES" DURING TAL CALCULATION...[C384]
@hesham essam sorry for my English not very good 😊 my turbocharger start working no no good.have overboost .After flashing ecu.i flashing because have stage 1.i trying return original software
你好棒,我喜歡
Thanks
Hi hesham, very good video, do you know how to flash a HU module,with Esys, I got a constantly rebooting issue.
Hello ... thanks ... will be same way as i think
How did u get ya battery volts to show mine wont can you please send me your link
Tell me a second too see battery voltage
Hi, I have F20 BMW 1 Series 2018, when I check ISTA it shows there is no communication with EPS, do you have any idea what the problem could be?
Check.power ground ... maybe eps.itself
Hi brother, I would like to update the DME module in my BMW, should I use ISTA or is safer to do the update with ESYS? Thank you
I prefer esys
@@heshamessam8042 okay. Thanks👍
Ok after thinking and looking in the codes i found what i need and i programmed succesfully thank you sir !!!! Thanks to your video now i have coded EPS🎉🎉🎉🎉🎉
😃😃😃
Same procedure is in case to change a tms module ?
Yes ... if same fault .. also may need to do on frm itself ... also may need to initialize with ista
@@heshamessam8042 i have a coding error on diagnose.
@@dragos002 ok ... cafd missing... go firstly with esys
@@heshamessam8042 thank You sir i will try
Hi Hesham, can I use this method for flashing other ecu's? kombi bdc etc etc?
thank you for the videos
Yes thanks
@@heshamessam8042 sorry I wanted to understand if it is also good for the Mini F series
@@AntonioArsuta yes
@@heshamessam8042 hi, sorry for asking for more information.
I flashed the ecu but not all, then today I went back to connect to flash the rest of the ecu but it doesn't allow me to do full flash anymore, it gives me not available on i-step Target and shipping, what's wrong?
@@AntonioArsuta make sure to choose correct istep shipment ... also newer data (target) ... or maybe wrong fa or wrong isteps written on fem
One more question??? Can that coding be done with the engine runing?
Yes ...
@@heshamessam8042 thank you!!! Your video helped me a lot!!! Now i cant start programming the EPS
Thanks
When im doing the calculation for the TAL file appear a message telling me 3 TAL LINES HAVE BEEN SENT TO STATUS "NOT EXECUTABLES" DURING TAL CALCULATION...[C384]
@@thorsoldier666 and then can't continue performing tal?
are you using ICOM or just Enet
Icom
@@heshamessam8042 original?
@@zumiezskater122997 orange one ... icom a2 ... chinese as i think
@@heshamessam8042 orange one works with G series cars ?
@@zumiezskater122997 yes
Hello I flashing ecu with esys new have overboost🙈
What do you mean by overboost? I don't understand clearly
@hesham essam sorry for my English not very good 😊 my turbocharger start working no no good.have overboost .After flashing ecu.i flashing because have stage 1.i trying return original software
@@joker8541 never mind me too ... i think now all ok ... because esys use original stock files
@hesham essam but now after the update ecu the turbine is not working properly
@@heshamessam8042 before that everything was fine until it was stage 1