Spray Paint Nozzle FIX! Broken nozzle / tube! L@@K!!
ฝัง
- เผยแพร่เมื่อ 28 ม.ค. 2019
- First off...USE SAFETY GLASSES!! Secondly, PLEASE hit the subscribe button!! For this video, I used a red spray straw off a can of carburetor cleaner, WD40, lubricant, etc. I took 2 drill bits, 1.5mm then 2mm to drill out the tube in the can so the red straw would fit tight. Be sure to DRILL BY HAND, do NOT use a drill to drill the can tube out!!! I put the red straw in a drill and locked down the chuck (like you would lock down a small drill bit in your drill...just want you to understand what I meant). Using small pieces of different grit sandpaper, (one grit may be fine but I used 3 starting with courses grit first). spin the red straw with a drill and with your other hand, wrap sandpaper around the end of red straw to sand it down a little....basically making the outside diameter of red straw smaller so it will fit in the tube inside the can (the tube that broke off and can't be pulled out). I cut the straw aprx 3/4", may need to cut it a lil shorter next time and I pushed it down inside the tube of paint can, VERY slowly I pushed it down in it. If you sand off too much which I have not had that happen yet, just use another piece of same straw. Also, u can try without sanding....I had someone say it didn't need sanding but I wasn't gonna push that hard and spray paint on myself. I then put a small amount of super glue on the red straw sticking out of can then pushed the spray nozzle (the one I said I had off a can off empty black spray paint) down on the red straw. I let it dry then tried it out and it worked!!! I hope you liked the video and hit the like button and subscribe as well....I plan on doing a lot more and BETTER videos since I have received sooo many "Thank You comments" Have a good one! the Menace
![[FULL EP.14] เซียนหรั่ง สอน มาร์ชจุ จับปูนา ฮากระจาย | เฮ็ดอย่างเซียนหรั่ง | One Playground](http://i.ytimg.com/vi/M8mPjd_T2lo/mqdefault.jpg)
I turned around to grab the can for the second coat, knocked it off the table and snapped the cap right off... After a few choice words for rustolem my first thought was I knowTH-cam has a fix. Here we go again! Thanks for the video.
You are Welcome, I hope it worked so u were able to finish your 2nd coat. I've been keeping those little straws and some fit without sanding or they are making them thinner now to save money.....lol
Just got a can of carb cleaner ,and used about 1 squirt out of it.
It was sitting on the floor and I had to step over it,not lifting high enough and busting the tip out.
I knew I'd find a fix here.
Bro same shit, I just dropped it going for the second coat
Awesome thanks for the tip. I bought a glossy black. Used it once and it's still full. I dropped mine while I was using it. And it broke off. Asked my man if he can fix it. He said it was unfixable. Well I showed him this video and proved him wrong. 😁 Gotta love the Internet. Always a will and a way😊
That's right! I don't believe in can't....lol
This is what TH-cam is for. Thank you sir!
Yes sir! I wish I would have shown all the steps but I assume too much at times. I am very glad it worked for you!
Hey, my man you are a f..ing genius. I’ve wasted so much money on wasted paint and class cleaner. I hope it works with my glass cleaner cans. Great problem solving thanks for sharing.
Thank you for the compliment! It really amazes me at how much response, compliments, etc I received for my first and for now, only diy video. It seems this has helped so many and back when I had this issue, I couldn't find much at all online about this. Now, they have videos of actual packs of replacement nozzles but unsure if they work for where the tube breaks off nearly flush with can...lol. Let me know if it worked.
This is what I love about the internet. I used about 5mm of the extension tube from a WD40 can and drilled a hole in both sides of the broken bit and stuck it together. You Beauty !!
The same happened to me today about to put on a second coat. Damn lids. Glad I came across your video. I'm going to go try it now. Thankyou great idea!
Should work.....did many times now and seems to be working for a lot of others. Good luck and thanks!
@@dgmenace73 It worked perfectly. I did what you said. Put the straw in a dremel to sand it. Used the drill bits by hand. No mess and easy. Thanks man!
Thanks man. You just saved me an hour of messing around.
You're welcome! I know I spent no telling how long looking at videos and then came up with this....its simple and works.
I was shaking a fresh, new can of expensive Tamiya hobby paint in one hand and fiddling with something on the table and dropped it before the first spray. This will fix it! You are saving a bunch of paint from the landfill unnecessarily. Bravo!
Great! Glad it worked and glad to see you in the RC hobby!
thank you so much I thought about trying something but didnt want to get paint allover. I was painting an airsoft rifle I got one coat on put the cap back on when I took it off it broke and this video saved me I was so happy thanks
Meant.....glad it worked for you. I know I searched and watched a lot of videos on this but none really helped. Was very happy this worked. I've got a few dislikes and emails saying why waste my time on a $12-$15 can of paint.......my reply was, to me that's not cheap and also if it happens right after you start or halfway through and you don't have another can.....you save yourself a trip to store as well as the $ spent on another can.
The spray paints from this brand always break when I use them. I thought it was just me, but my friends also had the same issue..thank you for the video I will try!
You're welcome...I hope it works for you as well...I have received many messages thanking me because it did work for others. Good luck and wear safety glasses
Good paint brand and little pricey too, but they're using cheap material.
Hey, it worked for me too! Thanks for the great idea!
Awesome!!...glad it worked for you too. I actually did it again on another can and it worked as well. I think a few people wanted me to show step by step in the video but I didn't want to drag video out. Thanks for watching!
Thank you sir, just to let you know how helpful your video was, you just saved me $25, not to mention that i'm in saudi arabia 😅! TH-cam is a fabulous gift to humanity 😎
You are very much welcome!!! I had this happen to me and I searched TH-cam, watched no telling how many videos with no help.....that's why I made it, to help people!
I went to use the drill bit and the can sprayed directly in my eye, I went to wipe my face in a rush with paint thinner then I ended up burning my eyes and face with it, please make sure to use safety glasses if you are to proceed with this trick.
Also don’t rub you’re face with paint thinner
Yes, wear safety glasses anytime you are dealing with anything pressurized. That's one reason I made the little comment about not getting paint on me yet (I knew there was a chance of getting paint sprayed on me especially since that was the first time I tried it). I also twisted drill bit by hand to help prevent accidentally spraying. If you do get paint on you , especially in eyes....flush with water , no chemicals . Paint thinner is very irritant to the skin and most definitely your eyes. I had on safety glasses but it wasn't seen in video. I have did this little trick at least 10x since the video helping out people I know with cans of paints and other sprays.....so far, no accidental sprays. I'm glad you are ok and know to use safety glasses and now know not to use thinner on your skin. Kerosene works well on hands but wouldn't use anywhere else and would wash with soap and water afterwards, then apply hand lotion.
darwin award runner-up
@@florascent9ts lmao i did something like this too can i have it
Sounds like something I would do too. 😂👍
Thanks! I knock caps off now and again. Use to cut the can open slow to release the pressure and use what I can. .don't last long cause most of it evaporates. This tip is gold. Thanks.wil try it in my silicon spray .
Yw....good luck!
You sir are a genius.
Thank you...I am just a man trying to live life the best I can. Definitely no genius....people tell me that often but I am just a "tinkering" kind of person and try to fix something rather than buy new. I appreciate your compliment though, I REALLY do. I have been a mechanical/electrical/pneumatic technician for 23yrs and was just told I could no longer work the "typical" job and went through the disability process. My first appearance with a Judge I was awarded disability. This is because a motorcycle accident caused me a lot of health issues that caused attendance issues at my job. I was let go while on medical leave. Yes, while out of work on medical leave I was terminated. That was it for me so I do appreciate comments like you said. My God bless you!
Good job man! glorious southern accent!
Definitely southern accent and I don't realize how much into I listen to myself!...lol
You're an ace have three or four same issue...Excellent !!
Glad you like it and hope it works for you!
I figured this was the way to do it but I didn’t want to wear a paint eruption lol. Headed to the garage now to face down seven or so of these that have been sitting on the shelf collecting dust. Thanks for sharing.
When did "figure" that, right after you watched this video?
Thanks for the video you just saved my can that I ordered online
YW....glad it helped. Surprised at the amount of comments but very happy it has helped others out because when I searched , I didn't find many useful videos that worked.
I did the same thing yesterday..Topnotch mate
Glad it worked for you!
Great video for common problem. You saved many a lot of time, money and hassle, and, them cans don’t end up in the dump all full.
To keep from potentially spraying one’s face, besides goggles, wrap a little tape to seal straw; it will at least slow down any accidental spraying. If you use strong tape you might pull the straw out when removing the tape. Or maybe just snip off a little of the taped end when all done with the fix.
Good point....you can never be too safe.
Thanks dude, just fixed a break cleaner can with this trick =D
You're welcome! Glad it worked for you! I wish I would have done every step on video but this was my 1st diy video. We live and learn & have to start somewhere.... lol.
Brilliant!
Thank you! I hope it works for you.
I "accedntly" throw a can of starter fluid this helped alot thanks man
You are welcome. I am still amazed that lil ole me has helped so many out......but that's me, I tell people how to fix things instead of saying bring it to me and I'll fix it, then charging someone. I think information should be free and do what you will with it, if that makes sense.
genius . thanks man, know i can use 3 cans i dropped and broke
Thanks...hopes it works for you!!!
Dennis Griffith , just did it again yesterday, on a more than half full of black semi gloss, first try didnt work , think i drilled it too wide, then i used some orange fast set pvc glue on the red straw and it worked w no leaks. just painted my tractor yesterday. thanks man, now im kicking myself on the last few almost full cans i tossed out a week before seeing your video. thanks again bro
You're definitely welcome! I just couldn't throw that $16 can of paint away....lol
Dennis Griffith , exactly , i just watched another video yesterday of a guy that transferred paint from one can to the other, he stuck the good can in the freezer and the one w broken tip under hot water , and put them upside down and transfer paint. took him 3 times to get all paint out but i thought that was another neat trick
I have three cans also
Thank you for this video. It was very helpful for me.
You are definitely welcome.
Yay! Thanks for sharing
You're welcome!
You can also use a thumbtack or a needle to pull the broken piece out, just stick it into the side of the broken tube and kinda pry it out. It takes some effort but after you're done, you can replace it with another nozzle.
Nope the straws inside the can unless you've got the other type of spray paint can
@@crackedthieves Agreed, you can't do that because it's one single undetachable piece... there's nothing removable at all.
Good upload my friend!
Thanks....I hope you tried it and it worked for you.
Thank you very much😊😂😂 I need that😊
thanks man, it really worked 😁
Awesome!
Awesome, bought a new can and broke the nozzle trying to get the lid off. Thanks!
You are welcome!
Samee bro
You have more patience than I do... I just take the can outside to a field on my property, along with an air rifle, and make a reactive target out of it... gets rid of the paint... the paint goes on the weeds that get mowed, and no paint pollution by just tossing the can in the garbage... I also shoot empty cans to relieve the pressure before tossing the can out or recycling it.
Helps to have the proper place for airgun shooting !
I get told that all the time about my tinker patience but it to no more than 15min....and someone wanted me to paint something for them and they bought the paint so I was determined not to have to pay $13 for another can.....lol
lol, that's one way to get rid of spray paint cans.
I do that too....if paint is just no good, especially if pressure has leaked out. I just recently made some anti ricocheting "plinkers" . I used rebar to make quick assemble and quick disassemble stands, big nuts welded to heavy chain, then welded to 1/4" to 3/4" steel plates I cut in different shapes, sizes, and thicknesses to get different plink sounds. Up to a 308, it stops the bullets dead, I can find them under to a couple feet away from targets, no dents. I use field marking paint like for football fields, paint the steel with a very heavy duty paint then later on just spray a thin coat of white marker paint, you can see where each bullet hits. I may make a video on it
I was able to use tweezers to pull it out! Thanks!
Cool fix will try it. I have half dozen spray cans with broken nozzles, some I could reinsert the tip most could not, some never got a chance to use.
I hope it works for you.....it seems like most break off just high enough to not be able to reinsert the nozzle, or in my case that's the way it seems. Good luck!
@@dgmenace73 The ones I couldn't fix, will drill a small hole to release the pressure then use a saw and save the remaining liquid. Gloves and full face shield. Also do this when those cans run out of compressed air.
Thanks for the info Dennis trying to do the same thing with this can of brake kleener cause in to cheap to buy a new one lol.
Hope it works
You Rock! Thank You So Much !! 🤘
Thank you! So glad I did this lil video and helped so many people out! Really makes me feel appreciated!
Great idea. I bought the same brand of paint and the break was identical. Thanks for sharing this
You are welcome. Glad I was able to help you!
Genious! Thank you so much!
You are welcome.....I have been getting so many, Thank You comments, except for a few saying I should have showed in the video every step (even though in the drop down I told every step I did), then also a couple that must have used a drill to drill the tube out???? They got sprayed...I thought I was fairly clear to do it by hand so getting sprayed would be less likely. Also, I think we have to use common sense when working with pressured cans.....this idea is just to be able to use paint that we basically just bought and the tube in the can got broken most likely when pulling cap off.
Thank you! I'm gonna try this tomorrow 🤣
Good luck!
I bought a can of paint only to find the straw is broken a month later when I finally got to use it so returning it isn't an option. Thank you so much! I'm excited to finish my projects
You're welcome! Glad it worked for you!
Hii
Same - thanks for the idea. I'll try it
could save my £20
@@mariehurley917 I hope it continues to work for everyone. It really was a simple fix and the videos I found prior to mine were not much help. Just wear safety glasses and gloves. I have done a few more since this video and they all worked. One there was NO tube at all sticking out of can and it worked as well. This is just something to prevent from having to throw away good (some very expensive) paint and have to buy more when you can do this and use the paint instead of having to buy more. Most of the $2-$6 paints you can replace the sprayer because the spray tip has the tube on them? Idk why but the more expensive paints have the tube in the can, not the nozzle? Enjoy and so glad I have helped you all out.
Nice thanks
Thank you so very
Much !!!
No problem...glad it worked!
Thank you 😊
You're welcome and good luck!
Thanks 👍👏
You're welcome!
Thank you!!!!
You are very welcome! I hope it worked for you as well as it has others.
Thank you
Strangest thing just happened I looked up rust oleum spray tube broken off in sprayer tip.
Your video came up and guess what kind of paint I was also using… Well let’s just say it wasnt. Gold. But was not far off….
SILVER metallic but the exact same stuff!!!!!! What the!!
Yeah, they have emailed me since this video saying that there will be a change in caps & nozzles this year.....lol
Very good, Originally I tried to do this using a cordless drill. Don't do that. Makes a mess. great thinking.
Yes, I imagine it would. I was too afraid the weight of drill or me accidentally pushing would cause it to spray out on me. I was surprised at how easily the 2 drill bits worked just by hand
Yes, exactly why I said to do by hand....Definitely use the drill only to spin the red straw with sand wrap around it.....drill the can by hand, easily
nice job buddy! I am not sure if I have the patience to sand the replacement straw down to fit inside the broken one though. been waiting all week for the weather to warm up and quit raining so I could do this spray paint job and sure enough I take the lid off and break the nozzle. why do they have to make those spray paint lids so hard to get off? anyways, you gave me something to work with. see if I can get mine going again.
Awesome....just put the red straw in the chuck of a cordless drill.....spin it and grip sandpaper around it....it only took 15min the whole job....then 30min for super glue to dry but u may not need the super glue. I hope it works for you. Did several more since the video without super glue. The drilling of the can tube was very easy as well....just twisted the bit by hand. Good luck!
thank you, worked like a charm.
Awesome! You're welcome.
I bought a brand new airconditioner cleaner ( very pricey) thanks for the idea !
You're welcome....glad it seems to of worked for a lot of people.
Thanks tried other methods
paint everywhere.
I'll try your way.
Hopefully u this will be successful and you will come out with less mess. The drill by hand and being very careful helped with me but I have fairly good patience
Exact same shit happened to me when I took the cap off.. pissed me off brand new can.. how tf is it so hard to pop the top off but so easy for the nozzle to break off
me to brand new cam knocked it off the table broke I was like SOB my damn fault but yeah make a tube works good thanks
Nice this video just safe my can of brake cleaner and future ones
That's good! That's the reason I posted it is to prevent us from wasting $ on cans of paint, cleaners , etc....those tubes break easily.
just might work on my air freshener Thanx
YW
Hey Dennis Griffith. Nice video can't wait to try it. Meanwhile can I ask how you liked the gold paint? Thinking of painting up some metal moldings for cabinets where rats have chewed the wood.
I liked it a lot! Used it to paint yard flag poles, lantern hangers, anything that was gold from factory and paint had flaked off or rusted...that gold paint worked great
I just removed another comment about just buying another can instead of going through this...smh. I think this took 10min to do and where I live this can of paint was like $12.95 and I live 25min from where I purchased. This works for $50 cans of automotive clear coat, paints, etc. If you got the money & time to go buy another can instead of taking a few minutes of time to do this, then by all means...sure, go buy another can of whatever broke on ya. I know I have certain kinds of paint or chemicals that are a couple years old but still good. This has worked on those too. This is for someone that doesn't like wasting money, product, or time....just saying.
How did you get the spray nozzle to fit the smaller diameter straw? BTW, those old Chilton Manuals are collectors' items.
I have did this a bunch of times....all the carburetor cleaners or brake cleaners' red spray/aim straws that I have tried have fit the red and white colored nozzles off the brake/carb cleaners and as many paints fit the bottom of the "replacement" nozzle (the red one in my video that I mentioned it came off a cheap can of black spray paint ...u can see a little black paint on nozzle right b4 I aim into box) they have all fit the end I DID NOT sand down......the reason I used bits to twist with my fingers to hollow out tube inside can AND used the sand paper to make red straw thinner is so that I would not have to make Only the tube in the can larger which would makes its walls even thinner and the same with red spray straw, I didn't want the end going inside broken can tube so thin that it would break easily. Does that make sense? If not I can explain it better. Oh, and yes....I have about 10 or 12 from vehicles I have owned, where I worked on other people's cars/boats., etc......I just found one on old OMC outdrives, an old early 80s Suzuki , then several for Spitfires....think I may sell them, will never use them plus sooo much is available online its unreal, but I do like having my own book...lol. Is it just me but are the books leaving out a lot and or just barely touching on issues/instructions nowadays? Thanks for watching, I hope it helps. Oh, go to a Dollar Store....look for their cheap, $1.50/can paints to use the nozzles off them. They also sell starter fluid which I can't remember is cheaper than carb cleaner or not but I saw the cheap priced paint and opened in store, I carefully pulled nozzle off the paint and had starter fluid can as well, I checked the fit and the white nozzle off paint fit the red straw tight.....thinking you could make a couple spares to keep near your paints?
Now I’m gonna try this with all the broken cans of spray foam... any ideas for those ? Tia
I haven't tried it....I would "think" if I could melt, dissolve the foam dried in inner straw it may work, I may try that....lol
I have been looking to buy 100m of the red or transparent mini tube tip but it is really hard to find. I believe it is nylon though.
Good idea. I just bought 10pcs of 2 different size tubes, all the red kind
Hey griffith, can I fix my butane someone scratch on the floor broke it and found all the nozzles again. There's no win or losing please help
I really don't know....I think I have an about empty can of butane...I can see what I can come up with. I do know those butane tubed are fairly thick to support the pushing.....will let u know if I figure out anything
A bit tricky but nice job
Yeah, have to be careful but it does work to where you can continue using paints with broken tubes. I also found a way to "repressurize" paints, wd40, etc but it will have to be a much more detailed video. I do apologize for not actually filming more of this process....I may do a Part 2 with no steps omitted as far as viewing the process. Thanks for the comments and likes.
Im legit mad that rusto switched to female caps. Ive used a TON of paint and never broke a stem off but today i had to paint 40 feet of baseboard that needed to be replaced from water damage and I bought a big can (15+ozs) for like $11. And it fell off the back of the truck while i was unloading, broke the can lid and the stem broke off inside the cap.
Unfortunately this trick only made it sput and sputter and was very low pressure. Also, even though my wd40 straw was short, it kept breaking off too. Then i tried drilling the hole big enough to accept a male cap that was sanded down a bit. That didnt work either. It still spits and sputters.
I understand your frustration. I wonder if your can possibly has other issues? It's worked for me at least 8 times and I've received a ton of replies saying this worked....I would demand an exchange if you don't live far from the store . I live 30min from a store that sometimes has it in stock...lol. I wish they all used the male nozzles too. Sorry this didn't work out for you.....It almost sounds like your nozzle is partially clogged. I saw where soaking in fingernail polish removes cleans out the nozzles....just an idea.
Paint everywhere 😂
Uh'O...I've been fortunate so far, I'll probably get it one day on a tube with weak spring or something...lol. Heck, they got kits now for this problem. Nice metal nozzles but they expensive!
me and my mom literally just bought bug spray and I dropped it trying to kill a spider . thank you for this. currently fixing it before she finds out
Awesome! Hope it worked for you!
Did it work for you?
@@dgmenace73 it sure did 👍
Tx
Rustoleum is the best spray paint on the market. I don't know when they went to this nozzle design, but its stupid. The cap is so hard to remove this has happened to me many times in a few years. I just sent a complaint to thier customer service, as they have ruined another of my projects.
Yes, love the paint....hate those caps that are difficult at times to pull off....I'm also the kind that keeps the caps on or puts them back on after use....I also turn cans upside down and spray the paint out until just air comes out to prevent the clogs.
@@dgmenace73 Just happened to me for the first time after I used about 10 cans in the past with no problems. I just removed the cap and it broke the straw. And it happened with the most expensive new paint can. I will try to find the receipt and replace it. This sucks. I tried super glue to glue the straw but it didn't hold.
@@ronenfe yeah, if u have the receipt and store is local, I'd take back as well.....the original (especially on the expensive brands), have a better spray pattern. Most of the time I am care or at least try to be but sometimes not thinking, and in a hurry I have done that but MOST of the time its because the can fell and broke tube...smh. Good luck getting your return!
@@dgmenace73 luckily I found the receipt because it happened the same day I bought it. They replaced it without problems. Be careful when you open the cap. Better to leave it without the cap.
@@ronenfe good! I hate it when stores don't take a return. Our local Walmart says they are not taking returns because of this Covid-19 situation...smh. There is a video on TH-cam, you will have to search. It shows how to make tops easier to pop off once you remove it the first time. If anyone knows were you can get automotive paints, in a large spray can for very low price....please let me know. Thank you all!
Same thing happened to my rattle can of Rustoleum enamel. Pull off the cap any way but perfectly square, and snap the straw into a jagged mess. Honestly, that's ridiculous. The big moral I'm taking away from this is to switch brands...
I just bought another can , same brand....totally different spray nozzle. I emailed Rust-Oleum the link to this video and complained. They sent me another can just like in video and said they had other complaints . I'm sure there are plenty of the old style in circulation though....it's definitely terrible that so many people had same problem with same brand and I agree.
Please elaborate on what the sandpaper is used for?
I only used the sand paper to prevent having to drill into the tube inside the can more. I have found that all those red straws are not all the same size. Some don't have to be ground down much if any. I use whatever grit I have handy, its not like sanding furniture or body work where it has to be nearly flawless. I usually grab a course sandpaper, lock the red straw in a drill as if it was a drill bit, wrap the paper around the straw and spin until I can fill a definitely difference in its thickness, then go with a fine grit to smooth it out. Hopefully this makes sense. It doesn't take much to get a red straw to fit in one of those tubes......I just didn't want the main "working" tube in the can to be too thin nor the red straw to be too thin so I drilled the white tube by hand to make the inner diameter of white tube larger and then sanded the outer diameter of the red straw to be smaller to slide into the white tube. Thanks and hopefully it works for as it has the others.
If you don't take the necessary precautions with a Canister with high pressure inside, then please also make sure that your "test aerosol" is a color that you like on your face. Preferably, not pink lol!
Could you do this with a big can of Lysol? My wife broke the nozzle off.. or does the straw have to physically hit the bottom of the can?
Should work on about anything...I don't think I can remember this not working on anything I tried it on (chemical, paint, etc.).
Ty for this. Kyrlon has such a shitty ass can design where thr lid is IMPOSSIBLE to remove so much so that when you try to force the lid open it literally breaks the nozzle and I cant just throw a whole can away for risk of it exploding and hurting someone im never buying krylon again so mad
Hope it works for you. It's worked for a lot of people on here and I'm glad . I can't stand to have paint I know is good and having an issue preventing me from using it...lol
Every time the kids are hard as shit to take off
seems to be a special Rustoleum feature this...
Yeah, they seem to be the worst about it. I did hear they were trying to correct the issue.
I hate that it’s cheap plastic now and not metal, dropped my can and it broken on carpet
Is this a common thing with the restoleum cans?
Yes, for me it has been and from the comments, others have same issues
Yeehaaaw
All the guys that disliked this video all sit when they piss.
Thanks I’m gonna give it a try on my brand new can of carb cleaner that I dropped and broke the tube on
why dont spray cans and gas tanks work any longer?
From what I understand they will leak due to seals going bad, hot or cold temperatures (like in a garage or storage building).
This happened to me just now with thesame product🙄
I believe it. They contacted me and told me they were in the process of changing the tube/nozzle setup because of so many calls & bad reviews. Good luck if you try this.
Where do you order from? How much dollar for 1 pc?thanks.
They come free on brake cleaner.....I think the auto parts stores sell them for like 10cents.
@@dgmenace73 we are aerosol manufactory from china. And we do brake cleaner for 18 years. Quality brake cleaner And Low price. Welcome to order and cooperation together.thanks.
Hello I ordered a can of hair Mousse and the head was broken off. How do I safely open the can as it still has product inside it??
THIS IS THE INSTRUCTIONS BEHIND THE CAN👇
WARNINGS : Contents under pressure. FLAMMABLE - Do not puncture or incinerate.
PLEASE HELP ME!!
I have not experimented with those types. I would just wear safety glasses and see if one of those straws will be too small......I could be mistaken but I think they use a special nozzle to make it come out as a foam? Sorry I can't be of more help.
@@dgmenace73 Thanks for your response!
man....what to do when there is NO nozzle ???
U mean, like if nozzle fell off or was lost? If so, find a paint nozzle off a can of paint around your house or even some of the household cleaner nozzles....if they are close to the size of red straw, it should work.
Will it work on butane?
Unsure...butane may be a little different because of the pressure put on the tube to fill lighter, etc.....it may be worth a try? Sorry I can't help much more than this.
197,000 views as of today,.....
and.....
only 261 subscribers.
TH-cam is cooked mate
Thanks for the update. Any advice to get the subscriber # higher? My plans for the future are to start recording & posting my ATV repairs, tips, etc. The paint can nozzle video was just something I did out of the blue and I know that it can be noticed by this video (that I am amateur with video posts).
@@dgmenace73 I'm fairly- and unfortunately- certain that you have to buy those numbers, my friend. Hence the cooked redress.
The price?
-Idk, maybe just your soul 🤷♂ ; unless it's a p2p transfer of accounts and/or media. Maybe old popular vids, if you can swap content. I hate to speculate, but I do not tread those waters.
I do know that there is no way that:
*the imbeciles who improperly use the words 'actually' and 'literally' multiple times in EVERY sentence, play 2D 8-bit games that look like they would have failed immediately upon release -even if they came out in the 80's-, (yet for some nefarious reason my 7-year-old seems to be utterly entranced by)* could possibly have amassed millions of views and subs earnestly. Kids are very picky about who they sub to for some ephemeral reason, IF they even have the wherewithal or parental control freedom allocated in the first place.; I cannot adequately place it though.
That or have lady parts....
Dude those always break!
Instructions unclear how to get rustolium off wall
I use "Goof Off"," Oops", "Goo Gone", or fingernail polish remover if its stubbornly stuck or Linseed oil. I hope it this helps.
WARNING: if u drill too deep whole can will burst out. I fucked up my whole kitchen i suggest trying it outside if u really have to
Can you just exchange it for a new one at the store
I guess you could.....I had ordered this one online, then no telling how many in the years that fell or I just dropped it, after having for months or years. After fixn this one I went out to garage and found 3 more cans of paint broke off very similar.
Instead of sanding the straw to fit, just do the same drilling on the spray nozzle.
Thanks, I had to do that on one nozzle. I guess I should have been clearer in video but I sanded straw for paint can end because after using 2 bits it was pretty thin and didn't want to make it any thinner so I sanded the straw down so it fit snuggly. One thing I have noticed is those red straws, not all are the same size...even on same brand of brake or carb spray but haven't found one so different it would not work. Coffee stirring straws will work as well
Why are these things made so cheaply and always break?????
Idk....Rustoleum sent me an email that they were aware but definitely need to get a better setup huh?
I wish you warn people about drilling it incorrectly will result in THE CAN SPRAYING NON STOP COMPLETELY WASTING THE CAN. F i
That should be common sense...and exactly why I said to use small bits and DRILL BY HAND.....I actually showed me spinning the bit slowly with my hand. Any mod can be dangerous but I did say in the video to do it by hand.....the only time I said to use the drill was when I locked the straw in a drill to spin it while wrapping the sandpaper around it. It says on the can that it contains high pressure, use caution. I do appreciate ALL that have did this and successfully got their paint useable again.
He did say "drill by hand", and in the video, he doesn't use a power drill on the can .
Doggggg gonnnneeeee
Works 4sho!
Works with a screw
U mean instead of drill bit, use screw to make tube inside diameter larger?
Cool now go change your smoke detector battery
Nice catch! Lol
cannot see chooops
Yeah, was a lil camera shy then...lol. wished I had shown more of what I did as well.
Next time do a step by step so we can see what and how you do it. Just saying you did it doesnt help
Yeah, this was my 1st diy video. I did write it all out below video but some videos I have watched, for me anyhow, have been just too drawn out. I may make another with no gaps in video, every step videoed. Thank you for the suggestion and if I didn't describe it enough in the details below the video,let me know. Thanks
Good tutorial that show us nothing xd
You're welcome! So so many comments on how this worked for so many people....glad it helped!!!