How to Build RC Savage Bobber - Planeprint
ฝัง
- เผยแพร่เมื่อ 29 พ.ค. 2024
- This is full highly detailed build video of this 3d printed rc airplane. I will show how to setup all the electronics and how to assemble the entire airplane.
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmi...
See what else I am working on:
/ troymcmillan_rc
/ troymcmillan_rc
#3Dprinted,#RCairplane, #ItFlies
STL Files: www.planeprint.com/savage-bobber
How to Print Thin Wall: • How to Print Thin Wall...
Big Bobber Videos
Assemble Part 1: • How to Assemble 3D Pri...
Assemble Part 2: • How to get your Big Bo...
Full Maiden Flight: • Big Bobber Maiden Flig...
Quick Full Build: • 3D Printed Big Bobber ...
Products Mentioned:
Artillery Sidewinder 3D Printer: amzn.to/396eqIp
Artillery Genius 3D Printer: amzn.to/39cA6CZ
White PETG: amzn.to/2MvroIx
Black TPU: amzn.to/2Sw3Oe8
Orange PLA: amzn.to/3bBq13F
2204 Brushless Motor: amzn.to/2NTqsOt
20 amp ESC: amzn.to/37K2dcL
Emax Servo:
8x4.7prop: www.apcprop.com
CA Glue: amzn.to/2J8EvNW
CA Accelerator: amzn.to/3fpbycz
AR620 Receiver: amzn.to/3j4PbK4
DX6 Transmitter: amzn.to/3l6NFsD
3pin wire assortment: amzn.to/3l1xNYt
XT60 connector: amzn.to/3iyZWnf
Y-Harness: amzn.to/3jAFwvo
Screw assortment: amzn.to/2SvMxSs
2mm push rod ends: amzn.to/3nnjD4U
Z-Bend pliers: amzn.to/34mA0rt
Hot knife: amzn.to/34AGOB1
Drill Bits: amzn.to/3nIJzrx
*These are the settings I used for my Artillery Sidewinder 3D Printer for. surface layer 3. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!
Profile 3 Cura Settings:
Quality:
Layer Height - 0.25
Line Width - 0.4
Shell:
Wall Line Count - 1
Infill:
Infill Density - 0
Material:
Printing Temperature - 215
Build Plate Temperature - 60
Flow - 100
Enable Retraction - Checked
Retraction Distance - 1.3
Retraction Speed - 10
Retraction Extra Prime Amount - 0.3
Speed:
Print Speed - 100
Outer Wall Speed - 35
Inner Wall Speed - 35
Travel Speed - 80
Travel:
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 50
Mesh Fixes:
Union Overlapping Volumes - NOT Checked
Special Modes:
Surface Mode - Surface
Experimental:
Slicing Tolerance - Middle
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!! - วิทยาศาสตร์และเทคโนโลยี
![เปิดบ้าน เปิด Supercar อั๋นโอกิ เคยเอา rolls Royce เเลกพระ องค์ละ 100 ล้าน l [Nickynachat]](http://i.ytimg.com/vi/FeGwJwXauZ0/mqdefault.jpg)
I was too intimidated to build this plane. Until I saw this video. Thanks for sharing your build!
looks like a scaled down version of Peter Sripol'ls latest plane!
Loool
Its Red
Thank you for sharing your knowledge with us.
Stay on the summit.
Another great video! Awesome looking plane....I think I'll make this one next!
Fantastic!!!, amazing !!!. Thank you for sharing Troy
Troy, it looks like you selected standard PLA for this build. You could have also done this with LW-PLA. How do you think your results would have been different? Less durable? Better "floatiness?"
I was wondering the same thing. Please opine Troy!
I liked all video of this man.he design all planes very carefully and planned manner.most important thing is he puts all details of parts and the suppliers too.i just watch all video .i never build any planes but now i just watching every steps carefully including which electronics components he use.
Хорошо - понятная и наглядная инструкция по изготовлению и сборке аэроплана! Замечательный полёт классного самолёта, спасибо за ролик! Успехов вам!
Watched many of your videos. At the moment in Catia I am working on Canadair CL-415. Things are coming together with an actual water collection and dumping system!
Amazing design and amazing build-builder, totally addicted to your channel
This is the most genius 3d rc plane construction I have seen so far👍🏻 Love the look😍😍
Thank you
What an awesome way to use your 3D Printer
Thank u for the video! 😊 I am just printing one and it will be very helpful to me. Wait for the MB 339 assembly video.
Great job! Really 👏
Amazing work
Good print quality.
great job my friend
Good video Troy! Might I make a suggestion. Place a sheet of parchment paper on your bench, this way you will always have a clean surface to work from. I use it and have found CA won't stick nor the parts. Some masking tape will secure it.
Another excellent video Bruce!! It’s electric for me or glidering!!! Good to see the drag racing too....Laurie
A fantastic step by step guide by a well respected enthusiast. Keep it up.
ps is this plane ok for a novice pilot/builder?
@@garyrayuk Thank you Gary, Yes this planes an easy beginner airplane for a new builder. It is nice because it prints out fast and there is limited thin wall parts. Hopefully this video will help make the assemble process a bit easier. Cheers
well done!
I'm in love with bush planes
Good job.
Really cool man
Wonderful... another great walk-through. I actually understood your comment about dropping the engine part under the build surface in CURA to print that part in red. Great tip. How's the X1 working out?
That’s awesome
Very nice 👍👍👍
hello really nice work
Amazing build! Awesome!! Except one thing. I once caught my hair on fire by angling the heat gun up like that!!!
Brilliant sir
Great video, please could you take the prop off when working with the servos, it is very easy to accidently knock the throttle stick or reverse the throttle. Keep up the good work.
I enjoy watching your build videos. 3d printing RC planes seems to have become a thing. I never paid much mind to it as I thought it would be to heavy and fragile but it appears not.
One question. Shouldn't the string bracing be glued at the vertical and horizontal stab? Its not really functioning as a brace otherwise.
Hi Troy, Great Video! Question, what size battery are you using with the 8x4.7prop set-up?
Hi Troy, once again a very enjoyable video.
Every time I see the "wire" frame aircraft, it just scares me, they seem to me that it's just waiting to break. Any feed back on this fear?
Very comprehensive video. Wich type of lipo battery do you reccomend?
Great video and build. Planes colors look fantastic.
In your materials list you list white PETG. Is this what you used on the wings instead of regular PLA?
Would be cool to see you build the rc3dprint Dragon bushplane!
Great video, I'm working on designing my own cub with some of my engineering buddies. Were going to overengineer the hell out of it but i hope it'll turn out well. Were running it through physics simulations using Siemens. I have a ender 3 max at home and we're aiming for a 1 print fusalage becuase of the 1 foot printing area.
Sweet, would love to print a cub, please share when you’re done! (Or sell, I’d pay)
@@samroesch hah I'll let you know. Maybe I'll put a video about it. I do have a GoPro so we'll see
nice work ! Do you think it's possible to print the wing in LW PLA ?
Great video Troy! Well you beat me to it lol. I'm excited to finish mine and fly! Now you need to build a tow glider and use the Big Bobber to get it in the air!
Great job, well done . If I didn't produce so much plastic waste when printing, I would be at it - Greetings from Germany - Take care on you.
Its PLA mate. Made from starch and recyclable.
Looks great and really clean build , but heavy.
Any plans for making a frame to attach a clear cockpit window? Would be great for FPV👍
I could have used this a week ago I just finished mine using the same color scheme. I used your earlier video with the P3 and it helped. Used an ender 3 v2 and now that it is assembled I am beyond excited to fly it. The only issue I am having is that where the motor mounts is crooked on 2 different prints of the cowling in the slicer it looks like it should be crooked not sure if you had the same issue
its to make up for propwash
down and to the right
Hi Troy thanks for the video its great. I print a previous plane with your instructions the icon a5 and works great. Now i start printing this plane but when i print the large fuselage piece, 3 times the piece disconnect at the point where start the window, …. About 1 cm from the base. I dont know whats the issue. Any idea?
Hi.
I want to know if you reduced his size. This plane looks really good at this size.
We support and follow you and your channel is distinguished. Don't you think that the time has come to design bigger aircraft, any higher level than the aircraft industry?😍😍
Nice video! But is it possible to use Slic3r for printing the files?
Great video! From a printable dimensions perspective, can the SB be printed in an Ender 3 V2 or is there a different first RC plane you suggest for the 3 V2?
I printed mine on an ender 3 v2. Only a 5 failed prints. Lol, 3 of them weren’t my fault
That's a very nice airplane! Are you using a 2 or 3 cell 450mah battery?
3s
Does the cowling print have the proper angles to adjust for torque rotation?
Top demais vc vende o projeto
does the Horizontal stabilyzer fit on a ender 3?
are the 4 white wing pieces supposed to slot together? Also the orange tip. does it slot into the white wing piece? my pieces dont have any groves to set them in. Thanks
I am thinking of getting my first direct drive 3d printer. Would you think that the latest version of the Artillery direct drive printer would be a good pick? Would this be a good printer for my 3rd printer?
I haven't used the latest one, but it should be great for 3d printing planes!
That is really a sharp-looking little airplane! Very nicely done. A 3D printer is at the top of my “lottery list.” ;-)
which tpu are using for the tires?
Like. I've been opposed to 3D printing used in crafting Because I consider the final products a flimsy reproduction that should be wood or metal. However using this process to make something fly has now become a interesting challange.
What kind of use did you use for the movable surfaces?
The movable surface is printed with PLA and has TPU black hinges.
What emax Servo did you use? Cant get the ones who they recommended in the manual
I used the ones in the manual, but you can also use any 1.7g servo
Is that Lake Mead in the background?
Troy, could you detail your settings for the varioShore TPU for the wheels? Cheers. David
Hi David,
I printed varioshore tpu at
60% flow
240c
30 mm/s
10% infill
3 bottom layers
4 top layers
2 wall line count
.2 layer hight
It may need printed slower depending on printer
@@TroyMcMillan That's perfect... thanks Troy. I really like the look of those tires. I'm going to try them on the Big Bobber. Almost finished printing it. This is very cool stuff.
@@rcdavidk Yes it is very cool. I have not re printed the Big Bobber tires yet but I am definitely going to when I take it out again to fly. It is perfect material for large bush tires.
@@TroyMcMillan I just loaded the Big Bobber tire into the slicer and it reports 10.5 hours for printing... yikes. A wing part only took 7 hours. The little back tire is 30 minutes.
@@rcdavidk Ya the tires take along time to print for sure. But it is worth it they are awesome. 7 hours for wings is actually fast my wings for this build were all at around 10 hours each part.
Can I ask as no info on what lipo you used 2 cell ....3 cell cheers
Many of your Amazon links are broken. Any chance of updating them? I also haven't been able to find the 2 listed servos, but I've ordered some of the Power HD DSM44 servos. If they don't work, I'll be trying the Hitec HS-45HB.
What size servos did you use? the size they specify in the PDF file are like impossible to find anywhere.
I used the ones in the pdf file, and they were very hard to find, or you could use a cheap 1.7g servo that would fit too
Clicking any of your Amazon links just went to the same general on-line shopping page without showing any of the products you mentioned!
What settings would cause no printing of the inside structure of the wing panels?
put it in surface mode under the special modes tab!
does this plane support a 2212 1000kv engine?
Could you add some links to the same motor and servos you used in your build? This is my first RC project and my knowledge of different parts is very limited lol
I'm loving this! Almost finished with my first print on the Artillery Sidewinder X1 using your Cura settings and it is perfect, no brims! Looks like you're using the Emax ES9051 4.3g digital servos. Is that correct?
Hi, where did you get the seats you fitted to the Bobber? I bought the stl's but dont see it there? Its the main reason I bought it...
Go to the site you got it from go to the savage bobber an it a free download..
@@dooce100 Got it, thank you very much
Do you spray kicker every time?
I almost NEVER use it, it always causes discoloration on PLA. I only use it in the case of a quick repair, but otherwise I really avoid it as much as possible.
👌
hello, on which site can I buy this kit?
What is the wing airfoil?..
@10:58 it’s got a pressure cowling yet the cylinder heads are exposed.
How to get the STL files? Is it free for download?
How do we print the wheels with TPU material? Kindly send the template for printing wheels
Hi! At the end of my most recent video, I talk about how to print TPU!! 24:09 on this video, th-cam.com/video/b2Od4YHcLAQ/w-d-xo.html The TPU settings I used are in that description of that video too. Go check that out, I hope it helps.
Cuanto mide de alas y fuselaje
Love to see a lightweight foam printed pilot in the seat....or a goprp
Where is the carbon wing key ?
Where is your flying site?
I live in Las Vegas, For this video I was at Lake Mead
I cannot not get the landing gear top print right. Every time I Slice them in cura with your settings the print almost completely forgets about the entire sidewall of the gear and just prints the surrounding structure of them. It basically only prints half of what I'm seeing
Hi Troy, I bought the plane files but didn’t see the seats and the mount to screw the landing gear on, is there a new update to the files available somewhere to download from?
Also, I am using Gorilla glue (suppose to be strong) here in Australia, the back frame seems to be very fragile. Are you using medium ca with accelerator with every thing you are putting together? Thanks
The seats and updated main landing gear are in the free tuning parts for the Savage Bobber page on planeprints website. Here's the link https : / / www . planeprint . com / bobber - tuning. Sorry YT wont let me post the link directly
What microphone do you use
Can you pick and choose which airfoil... sorey..sailplane / motorglider pilot here...lol
Excellent bro I m build this plane my homemade youtube channel next video I m indian 💓💓💓💓💓💓💓
Would you sell me that in a kit?
I am not currently selling kits right now.
Almost 30€ for this “cheap” design?! Come on Planeprint, why are your models almost double the price of your competitors?
Market sets the price. If people are willing to pay the price, I say good for them.
@@samroesch yeah of course you’re right, but it’s still not nice 😅
info. good work. nice bobber. except, where it's not. evidence indicates that Every One of these printable designs contains at least one Major Flaw.!!! at 1:07, it appears that someone chose to use a thinner, less-optimal profile. consequently, the in-flight behaviors of the model should be expected to be 'less-than normal'. a main wing is Supposed to have a main spar, Located at THIRTY percent of chord. each of the main wing sections SHOULD have a correctly-located main spar. Design of the joins of the the segments Should INCLUDE a means of Solidly connecting the partial main spars, to one another.!!! the use of rib-like structures in a wing makes it more resistant to twisting. any ribs in this wing.???? in general, 3d printing results in a structure that appears to be monocoque, but isn't. in part, because, the covering is not 'functional'. at 14:44, this is a less-than ideal control horn design. the control horn pivot points are NOT optimally located. at 15:48, WRONG --- since there is no Actual provision for pivoting, there.!!!!! at 16:04, the longest wing struts are TOO wiggly, to be Functional.!!!! consequently, they are dead weight; that outboard-extending mass Has an affect on the airframe's span-wise dom !!!! at 17:27, can you spell, TRIM the Elevator --- FIRST THING.!!!!! is cg at 30? (at 2:38, called a tail boom.) googletranslate
Please be quiet, it's not big, and you're certainly not clever...🙄🙄🙄🙄🤔🇬🇧
I found the tail wheel structure is too short to reach the rudder when it is screwed onto the frame thingy. I am redesigning it and reprinting it.
I had that happen too, I used a piece of scrap pla