ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
How to Install a Catch Can Simplified
ฝัง
- เผยแพร่เมื่อ 16 ส.ค. 2024
- Today I am going to show you how to install a catch can on a BMW E36. The Process is similar on just about any vehicle using the same general principals.
In this install will delete the CCV (Crankcase Ventilation System) and replace it with a Catch Can. The Catch Can eliminates the problems associated with the Stock CCV that tends to get clogged up and send dirty oily air into the intake. Sometimes it can cause the engine to run rough and stumble. This upgrade will eliminate those issues and hopefully increase the life of our engine.
-
Don't forget to Subscribe: goo.gl/2SdRG8
-
🔧Tools used in this video🔧
Hose Cutter: amzn.to/2XCZIos
Heat Gun: amzn.to/2XbJYcG
Razor blade (for cutting a small piece of plastic)
Screw drivers / sockets for hose clamps
🔩Parts used in this video🔩
Catch Can: amzn.to/2FAM5Mn
Expansion Plug: amzn.to/2Xc8w5y
JB Plastic Weld Epoxy: amzn.to/2XaRYut
O-rings for fittings: amzn.to/2YfdJG1
Vacuum plugs for Dipstick tube: amzn.to/2Yhzyoo
Metal flat stock for making a mounting bracket
* The hoses needed for the catch can need to be able to withstand vacuum and heat. I used a combination of heater and fuel hoses. Most parts stores will carry hose for pretty cheap and by the foot.
* I would suggest bringing the fitting for the valve cover and the fittings from the catch can to make sure the inside diameter is correct. I had to exchange my hoses several times because of this.
IN from Valve Cover to Catch Can
7/8 Heater hose
5/8 Heater hose
Reducer 7/8 to 5/8
OUT from Catch Can to Intake
5/16 hose
5/16 Vacuum Tee fitting
Disclaimer
I am an Amazon Associate and I receive a small commission if you choose to purchase tools or parts through my links. They don't cost you any extra and it helps us to continue creating more fun videos like this one.
-
Our videos are for entertainment purposes and if you came for expert automotive advice, I am sorry 😅 because I am definitely not an expert. These videos are about our lives and our current Daily Drifter Builds.
We like to show the struggles that most channels try to make look easier than they are. We build our cars inside my garage with the limited tools we have available. I hope you still find my failures entertaining and have a great day!
-
Social Garage:
Instagram / the_daily_drift
/ austinatm
Snap us @kyle00088
Tweet us / the_daily_drift
-
-
-
Music Credits
TH-cam Audio Library Tracks
- Lost Highway
- Lonely Nights
- Half Pipe
- Double You
- Wild Pogo
- A Rising Wave
- Hyperspeed
Track: OLWIK - Villain (feat. Tyler Fiore) [NCS Release]
Music Provided by NoCopyrightSounds
Watch: • OLWIK - Villain (feat....
Free Download / Stream: ncs.io/villain
Literally the best catch can install and CCV delete video I've seen so far.
Instablaster
To my understanding you should direct the catch can OUT between MAF and throttle body, just like on M50. Then you will not have oil consumption when idling. Alternatively you can direct catch can OUT through aftermarket Purolator PV1050 or alternative PCV into your intake manifold.
lock tight the threads on the plug, no leaks.
Good video but I’m having some trouble,what was done with the icv valve?
How do you set up the catch can with the m50 manifold
Did anybody not do what he did with the plug can I just tighten it in I throw a o right gasket on the bolt before I expand it
Could I just rout the out to the port that you plugged in on manifold where the oil separator connects to the intake instead of T it in
ok when car is idling then the vacum in the intake is the highest. PCV adresses this issue by closing the membrane. Here with the catch can when car is idling it will just eat too much of your oil fumes. how is this problem addressed?
I had to use a PCV valve on my Oil Catch Can setup, I had too much vacuum that was causing my engine to run rough.
same here, threw in a PCV and no issues after and the catch can actually collects crap instead of injecting it back into the motor
I might have to look into that, so far it seems to be working good. We will see though!
Where did you install the pcv in the catch can system?
Just done today a catch can. Where bouts did u put pcv.? Thanks!!
@@jaidynpolson7939 you put the pcv in between catch can and intake manifold hose
Ok so for the vacuum lines what am I supposed to do the Evap I tap into it’s runs to the evap sensor the big port on the intake and then T into the catch can what do I do with 2 smaller ports and as the CCV and the EVap no take both positions in vacuum and the oil return to dipstick is capped just watched the video again the FPR valve goes to the line on the dipstick? But what about the check valve where do I rout that
An what about the big hose on the take where the Evap sensor originally was I just leave it there with that u shaped hose open like this is the closest thing I’ve found to a good install video and it’s still leaving out information
I've just finished this set up and am getting a whistling noise
The noise goes away when I lift off the oil fill cap, it seems like there's quite a strong vacuum in the crankcase, takes alot of effort to remove the oil fill cap
Any ideas on why it's whistling?
U figure it out
Is this can work in z4 2007?
We’re does the icv go
Any problems after 3 yers
If I reconnect it to the intake system wouldn’t it blow oil into the intake under boost
Yes it will, put a check valve inline so that boost pressure does not reverse the air flow and pressurize the out port on the catch can. Pay attention to the arrow on the check valve to direct the airflow from catch can to intake.
Dope!
guys do not use the expansion plug that thing is gonna get sucked in dont ask me how i know
That's why you add RTV around ut
That loud music ...
nicely done, more videos like this please