Paul! This was super helpful information. I've been scared to touch the tensioner and pulleys and anything to do with my belt and you explained everything so well. I hope to see more videos from you
How do you know what each one is called? The biggest one in the center on the bottom of my silverado is wobbly. Not bad but i can notice it when its running and im concerned bout that. So how to know the name. Each part has a name.
That would be your crank pulley/harmonic balancer. If that's wobbling, it's VERY bad. Like destroy your engine bad. You need to get to the bottom of why it's wobbling.
Keep the video's coming......Your explanations and filming the actual work is spot on.Ive never been much of a book learner,but can do about anything if taught hands on.
Thank you for this informative video Paul. I did all of your steps, removed the belt and run the engine but the noise still there. Seems to be behind the harmonic balance. Any idea what could be? Thank you again Paul.
My serpentine belt just broke. I heard a squealing noise but didn’t get proactive on it. Does the pulley wheel spin slow rugged when testing bearing failure?
Nice looking engine Paul.Would like to see a vid on all the upgrades you have done to you srt6.I want to upgrade my SC pulley and have a tune done.Would appreciate your advice,I don't want to go nuts since it will be me and the wife's summer cruiser but would like a little more power and some SC whistle.I've been reading on CF forum but even that gets confusing once they start talking about crank pulley's and sc pulley sizes.Thanks
So if your tension pulley spins freely fast after yu take the belt off is it bad ? And when I try to spin the power steering pump pulley it doesn’t spin very much
@@CrossfireRepairsByPaul my belt came off and it wasn’t because of one of my pulleys or bearings. Happened a few days ago and they all turn fine with no noise. I’m guessing it’s the front crankshaft seal that broke or had grease?
@jake t No.. that’s like spraying all the houses on the block when one house is on fire😜 They sell full kits as money grabs for fools who spend money on what they’re told too. Cough Cough**
Hi Paul, nice video, great content, I have question for you and maybe you could help with this. I have a Mazda Tribute 2008 4 cyl. I lost the serpentine and noticed that the top pulley was loose, so I removed it and say that the washer behind it was damaged (it's for the power steering pulley) according to a diagram I found online. The pulley is still good, not damaged. Would you know where to get that washer part without having to change all the pulleys? Many thanks, John
Need your opinion Paul, took my 05 crossfire n/a to a local shop to repair a tps they hooked up the obd2 scanner to clear the code and said that it wasn’t communicating, tried a brand new scanner same thing but I’ve heard that some scanners work on the crossfires and others won’t? Love you videos by the way!
Paul thanks for forwarding this video to me. Now I can pull the belt and change the super charger oil by myself....yea!!!!
that's great!! If I can do it so can you!
"... Wiggle it make sure there's no sound"
Pulley: chkchkchkchk
"Not a sound out of that one"
Lmfao
That engine is really nice. But thanks for the video. Easily explained.
Paul! This was super helpful information. I've been scared to touch the tensioner and pulleys and anything to do with my belt and you explained everything so well. I hope to see more videos from you
Uuuuuy
What if there is oil leak under one of the pulley
I have vauxhall astra j
Clean the area then start the engine to locate the exact spot where the oil is coming from. Then identify the parts required and repair
How do you know what each one is called? The biggest one in the center on the bottom of my silverado is wobbly. Not bad but i can notice it when its running and im concerned bout that. So how to know the name. Each part has a name.
That would be your crank pulley/harmonic balancer. If that's wobbling, it's VERY bad. Like destroy your engine bad. You need to get to the bottom of why it's wobbling.
Keep the video's coming......Your explanations and filming the actual work is spot on.Ive never been much of a book learner,but can do about anything if taught hands on.
I get a paint marker and draw the belt diagram somewhere on the vehicle, i don't get to work on anything nice as an srt so it's not an issue
Great idea, I will use that one!
Hope you have subscribe to the channel! 😀
Thx for the vid.
great information ,pointers om tool needed.
Thank you for this informative video Paul. I did all of your steps, removed the belt and run the engine but the noise still there. Seems to be behind the harmonic balance. Any idea what could be? Thank you again Paul.
My serpentine belt just broke. I heard a squealing noise but didn’t get proactive on it. Does the pulley wheel spin slow rugged when testing bearing failure?
the pulleys should turn easy when good and stiff and going bad
Love the video, thank you
Look at that beautiful M113k Mercedes AMG engine 😍👌
great point about youtube videos
Nice looking engine Paul.Would like to see a vid on all the upgrades you have done to you srt6.I want to upgrade my SC pulley and have a tune done.Would appreciate your advice,I don't want to go nuts since it will be me and the wife's summer cruiser but would like a little more power and some SC whistle.I've been reading on CF forum but even that gets confusing once they start talking about crank pulley's and sc pulley sizes.Thanks
Beautiful engine
Is it normal for the radiator hose to go flat? I'm asking because mine does that too and I wasn't sure if that was an issue or not.
Yes because it's not under pressure. No coolant flowing through when engine is off
Thanks!
If the hose collapses on its own when the engine is running, you may have an issue with the radiator pressure cap.
nice video brother
So if your tension pulley spins freely fast after yu take the belt off is it bad ? And when I try to spin the power steering pump pulley it doesn’t spin very much
Thank you😀😀😀😀
You didn’t really explain how the pulleys go bad my man. Care to share that with the rest of your viewers?
pulleys have bearings, they get used a lot, they have greased in them that go dry and can get dirt inside of them, therefore they go bad my man
@@CrossfireRepairsByPaul my belt came off and it wasn’t because of one of my pulleys or bearings. Happened a few days ago and they all turn fine with no noise. I’m guessing it’s the front crankshaft seal that broke or had grease?
@@antoninobalducci very much possible
@@CrossfireRepairsByPaul Was this something that I could have prevented? I’m pretty meticulous with my vehicle.
@@antoninobalducci only if you saw a leak before
Great Video!!!
Nice video
Just replace the lot and get a full pulley kit 👍save yourself the hassle
that's like changing all your tires when you have a flat in only 1
No its not at all pulleys and belt is something that should all be done at once hence why they do full kits on ebay 👍😉🙄
@@jaket9198 dont be a parts replacer dude. Diagnose the issue.
@jake t No.. that’s like spraying all the houses on the block when one house is on fire😜 They sell full kits as money grabs for fools who spend money on what they’re told too. Cough Cough**
That's just ridiculous.
Use a hose stick it to your ear on each pulley beatings😮
ok, so, how do you do that on those "pulley beatings" spinning when the engine is on???
Hi Paul, nice video, great content, I have question for you and maybe you could help with this. I have a Mazda Tribute 2008 4 cyl. I lost the serpentine and noticed that the top pulley was loose, so I removed it and say that the washer behind it was damaged (it's for the power steering pulley) according to a diagram I found online. The pulley is still good, not damaged. Would you know where to get that washer part without having to change all the pulleys? Many thanks, John
2000 ford ranger terpintin belt how to rePLACE
This dude has a thick Chicago accent.
Need your opinion Paul, took my 05 crossfire n/a to a local shop to repair a tps they hooked up the obd2 scanner to clear the code and said that it wasn’t communicating, tried a brand new scanner same thing but I’ve heard that some scanners work on the crossfires and others won’t? Love you videos by the way!
you are correct, many features require a DRBIII
Crossfire repairs by Paul thanks a lot!
Putting it back on can be a bitch. Some tips to that would help
Is this a C class Benz..?.
actually a Chrysler Crossfire
Crossfire Repairs by Paul benzes are chryslers anyway😁😁