Very good installation, particularly the radiator. Ive dyno tested various lengths on various specs, and as is obvious the short set ups like the DTH ones lack performance right through the rev range. Curves in the intake are not a problem if they're gentle. I tip the whole assembly forward via the inlet manifold or trumpets on a DTH set up then use longer horns. Once you get into the 360-380 zone overall from the valve you start to drop the peak rpm point where max power is made, but can add a little midrange or fill in holes if wild cams are used. 200hp and 170ibft is more than plenty before costs spiral upwards.
Thanks for the time-served expert reply. From memory, we can use the 3rd reflection wave when the track is as you say 360-400mm. Shorter than this use the weaker 4th wave in pulse tuning that's gone there and back once more.
I thought it may come in use for you. You're going to have to watch out for the water outlet in the top of the head if the KR one doesn't angle down like the ABF one. May be worth swapping to an ABF one if possible to give you that extra clearance?
@@markwagar8735 certainly a tight fit, but hopefully this video will give you a clear idea of what works and how it can look. Best start adding those items to your basket. 😅
@@golfmk2 I think your formula is great. Each video has purpose IMO. As they say there's a time and place for everything. I watched till the end, so you are on the right track.
Great video..I’ve been sceptical about running the Honda rad on my Vw due to the top fill rad and been a pain to bleed but I see you have made it happen 🎉🎉..what’s it like for cooling ??
On a drive this setup heads towards over-cooling, due to my low temp thermostat. Circuit use it is perfect, coolant temps in the 90-100 C, oil temps similar
That would be very interesting actually. I reckon there'd be quite a difference in torque between the two. @abf16vftw may know the likely outcome without even the need for the dyno runs!
Open filter should make very little difference vs the ITG JC50 Air Filter. Can incorporate this into a vid with the two different intake trumpet lengths
It'd certainly be interesting to compare figures for the two intake lengths as described in the video. Hard evidence between the differences the two intake lengths torque figures
Are you running vacuum advance with a plenum? I tought about doing it with mine on Weber 45s with my ignition management but not sure if it's worth it over TPS.
@@golfmk2 How is the ECU determining load? TPS? I saw the orange hoses and manifold and thought the load sense might be through direct load measurement rather than TPS.
@@ForSunday vacuum take-offs join and go the MAP sensor in the ECU. There's effectively a curve map that splits the load into MAP based speed density for small throttle openings, part throttle, and over this curve it is TPS based. The spark for idle is spark scatter, keeping the rpm stable in any condition
I don't actually use it, wanted to keep the expansion tank, so the cap on mine is gutted and links to the VW expansion tank. Could be accessed easy enough with the 2 extra top brackets removed and tilting the rad back.
Looks great, love the 3d printed trumpets
They look great don't they? Infinitely customisable with any length and curve you can wish for too.
Looking forward to seeing the post-rebuild startup!
So are we! We'll keep prodding him until he's done it.
Or just ply him with coffee...
Very good installation, particularly the radiator. Ive dyno tested various lengths on various specs, and as is obvious the short set ups like the DTH ones lack performance right through the rev range.
Curves in the intake are not a problem if they're gentle. I tip the whole assembly forward via the inlet manifold or trumpets on a DTH set up then use longer horns. Once you get into the 360-380 zone overall from the valve you start to drop the peak rpm point where max power is made, but can add a little midrange or fill in holes if wild cams are used.
200hp and 170ibft is more than plenty before costs spiral upwards.
Thanks for the time-served expert reply. From memory, we can use the 3rd reflection wave when the track is as you say 360-400mm. Shorter than this use the weaker 4th wave in pulse tuning that's gone there and back once more.
Always loving watching the videos you do always very informative keep up the gd work
Thank you! I didn't know about the effects of short intake length until we did this video, so a learning opportunity all round!
Great video! Love the car!!
Thank you. It's an awesome car that's been meticulously developed bit by bit over 2 decades.
Great and helpful video, thinking about doing ITBs on my ABF next winter.
With the right supporting mods and a decent length intake, the benefits are clear to see.
Great video. Gives me all the information i need to consider when i get round to finishing my engine.
I thought it may come in use for you. You're going to have to watch out for the water outlet in the top of the head if the KR one doesn't angle down like the ABF one. May be worth swapping to an ABF one if possible to give you that extra clearance?
@golfmk2 yes exactly. The kit I order has a an angled outlet as part of it. But yes room is Still going to be tight
@@markwagar8735 certainly a tight fit, but hopefully this video will give you a clear idea of what works and how it can look. Best start adding those items to your basket. 😅
Great setup and thanks for sharing
It certainly is a great setup and one which is too good not to share! Thanks very much for taking the time to watch and comment.
Awesome video. Enjoyed it.
Glad you enjoyed it. Appreciate the feedback. 😊
@@golfmk2 Very informative and concise.
That's good to hear. Would you like more of the same? Or do you prefer the variety of information type videos and more 'event type' videos?
@@golfmk2 I think your formula is great. Each video has purpose IMO. As they say there's a time and place for everything. I watched till the end, so you are on the right track.
That's really great to hear and some really nice feedback. We'll do our best to keep you entertained!
perfect video to popup while I'm trying to package this ITB ABA into my Mk1. Thanks for the info! Do you have that trumpet setup for sale?
Closing comment, I wonder which broken Mk2 will feature next😅?
Great video though chaps. Looks like there's plenty of space for moar powa 👀
With the chassis setup this car has, I'd like to think it could handle some serious power. 😎
Great video..I’ve been sceptical about running the Honda rad on my Vw due to the top fill rad and been a pain to bleed but I see you have made it happen 🎉🎉..what’s it like for cooling ??
On a drive this setup heads towards over-cooling, due to my low temp thermostat. Circuit use it is perfect, coolant temps in the 90-100 C, oil temps similar
Could you do a video on a dyno demonstration open vs closed air filter?
That would be very interesting actually. I reckon there'd be quite a difference in torque between the two. @abf16vftw may know the likely outcome without even the need for the dyno runs!
Open filter should make very little difference vs the ITG JC50 Air Filter. Can incorporate this into a vid with the two different intake trumpet lengths
It'd certainly be interesting to compare figures for the two intake lengths as described in the video. Hard evidence between the differences the two intake lengths torque figures
Nice work! What did you print the intake with?
Thanks, glad you like it! Intake is ASA filament on a Ender 3 V2 printer 👍
Are you running vacuum advance with a plenum? I tought about doing it with mine on Weber 45s with my ignition management but not sure if it's worth it over TPS.
As this ABF is running a coil pack, there is no vacuum advance
@@golfmk2 How is the ECU determining load? TPS? I saw the orange hoses and manifold and thought the load sense might be through direct load measurement rather than TPS.
@@ForSunday vacuum take-offs join and go the MAP sensor in the ECU. There's effectively a curve map that splits the load into MAP based speed density for small throttle openings, part throttle, and over this curve it is TPS based.
The spark for idle is spark scatter, keeping the rpm stable in any condition
How do you get to the radiator cap?
I don't actually use it, wanted to keep the expansion tank, so the cap on mine is gutted and links to the VW expansion tank.
Could be accessed easy enough with the 2 extra top brackets removed and tilting the rad back.