Scrolling through your vids and seeing the tablet. 95% sure your likely a lead Penske tech. Reasons from the tablet, and info on all major engines and apu stuff even. Am I wrong?
Hi sir i did get a coronado dd16 600hp engine with 18 speed trans 3.73 ratio and 24.5 wheel original from dealer i use to get 1500 rpm at 70 mph i use this truck for havy loads and was perfect and now i switch to dryvan 80000 lb wish i dont need all this power what i did is change the wheels to 22.5 low pro and the truck become 1500rpm at 65mph i did change the ratio from 3.71 to 3.21 and now get perfect speed at 1500rpm at 74 mph but now i notis that the engine eat more feul and i was thinking if anything i can do 7 program that lower hors power or anything to 7 better feul mile pleas wait for your answer
As long as it is the same part number. Like if you were to have the same module from a different truck that is the same you could, but not if it is a different part number. As far as I know.
Is this the Detroit diagnostic link and can you adjust the cruise control coasting and engine brake engagement speeds? For example I bought a 2019 Freightliner dd15 without the radar on the bumper or windshield but it has a parameter set so when I set the cruise control at say 65 mph it will Coast it down to 60 mph and then engages and goes back up to 65 mph. And then the engine brake doesn't come on until 5 mph over the Cruise speed setting. Is there a way to adjust that?
Yes it is Detroit diagnostic link and yes you should be able to adjust those parameters. However if you engine computers are password protected you’ll need the passwords to change speed settings and a few others
Do you mean what do you use to connect your computer with the detroit software on it to your truck? If that is what you’re asking, normally I would use the nexiq usb link. It is a little blue box that has one cord that connects to your computer and another cord that connects to your truck.
I keep having the same code pop on every 400 miles 3058 9 and sometimes 10 I done change every sensor that’s required to change for that code new delta pressure pipe sensor somebody please help
![CAMPปลิ้น | EP.83[1/2] เปิดแคมป์หลอนต้อนรับ 2 ตัวพ่อแห่งวงการผี!](http://i.ytimg.com/vi/2uPuHYHgwiI/mqdefault.jpg)
Does the software require you to be logged in to compare data with the server or will it still work offline
Wish I could of seen the screen better but great info man
Scrolling through your vids and seeing the tablet. 95% sure your likely a lead Penske tech. Reasons from the tablet, and info on all major engines and apu stuff even. Am I wrong?
hi, great info, do you know how to change in the new mcm, vin and esn?
@@vicdangc I think in the actions tab at the top you can “sync” the vin and/esn
Hi sir i did get a coronado dd16 600hp engine with 18 speed trans 3.73 ratio and 24.5 wheel original from dealer i use to get 1500 rpm at 70 mph i use this truck for havy loads and was perfect and now i switch to dryvan 80000 lb wish i dont need all this power what i did is change the wheels to 22.5 low pro and the truck become 1500rpm at 65mph i did change the ratio from 3.71 to 3.21 and now get perfect speed at 1500rpm at 74 mph but now i notis that the engine eat more feul and i was thinking if anything i can do 7 program that lower hors power or anything to 7 better feul mile pleas wait for your answer
Trying to establish CAN network between Woodward Easygen 3500XT and DDEC 4. Please help
Can you retrofit another module to this truck by change it's vin and serial. thx. just newbies.
As long as it is the same part number. Like if you were to have the same module from a different truck that is the same you could, but not if it is a different part number. As far as I know.
Hello
I have a 2017 dd15 and I have some questions about cpc and mcm parameters in programming. Do you have a way I can contact you?
What’s your question? Can I answer it here?
Does it need to be online or is this working offline? To compare perimeter
If you have to connect to the server, you have to be online.
Is this the Detroit diagnostic link and can you adjust the cruise control coasting and engine brake engagement speeds?
For example I bought a 2019 Freightliner dd15 without the radar on the bumper or windshield but it has a parameter set so when I set the cruise control at say 65 mph it will Coast it down to 60 mph and then engages and goes back up to 65 mph. And then the engine brake doesn't come on until 5 mph over the Cruise speed setting. Is there a way to adjust that?
Yes it is Detroit diagnostic link and yes you should be able to adjust those parameters. However if you engine computers are password protected you’ll need the passwords to change speed settings and a few others
I have the same issue on my 2020 cascadia
@@alreyindustriesnot if you have the backdoor pass generator🤷♂️
What do I use to plug this into the truck?
Do you mean what do you use to connect your computer with the detroit software on it to your truck?
If that is what you’re asking, normally I would use the nexiq usb link. It is a little blue box that has one cord that connects to your computer and another cord that connects to your truck.
Can I have your contact info and where do you have the shop ? I need something to look into my truck .!
Sorry I don’t have a shop or that software anymore.
Where do you get this software
diagnosticlink.nexiq.com/CommonRoot/Contact.aspx
I keep having the same code pop on every 400 miles 3058 9 and sometimes 10 I done change every sensor that’s required to change for that code new delta pressure pipe sensor somebody please help
static.nhtsa.gov/odi/tsbs/2016/MC-10199616-9999.pdf
Have you checked the two ports at the delta p sensor?