No doubt that you have made this tutorial very nicely & thoroughly but I have one question in mind, Is it possible to customize that level at the very top of the tank so that it switches off when the tank is filled completely? And is it possible to disable that automatic switch sometime in order to use excessive water flowing out from the tank pipeline for gardening purpose?
Great! This is the only video that clearly and fully illustrates the correct installation of this overflow switch. Especially the positioning of the weight and in English. Thank you
Excuse, Under what grounds do you put the WLC sensor at the bottom of the tank? I hear that it is not safe and it is not clean that the tank should get just empty. Is in this height the power energy saving eficient (saving your electric bills ?)
Sir, we don't put sensor at the bottom of the tank. We prefer keeping sensor at some 1 to 1.5 Feet above the tank base. In this video we have just explained the process of installation. You can adjust the height at your connivance.
I have a few question about the wire connected to the sensor!!I is it directly connected to the motor or we have another control circuit along with it....beside that,motor is located at ground level and the tank is at upper level so the water has to be pumped to the upper tank from lower tank ....i think a 25-30 ft wire is required from the sensor to the motor at ground level..thak you
Use single pipe to fill the tank and use the same pipe to withdraw water from tank when you switch n moter all air in taps goes out and side by side you tank allso get full. Use a T in boftom which put water from up side and take from bottom side or call me 8054399504
My experience tells this product has some simple and serious error especially sensor part. At the time of empty over tank condition this sensor works nice. But unfortunately, this sensor switch off your pump in the mid way of filling over tank. it means your over tank will be never fill up to your certain marked level. The problem here is that, they have used heavy thick cable with sensor switch which itself creates load inside water to flip your sensor upward. Otherwise, the controller part is nice. So my suggestion is to change the sensor cable by using very light electrical water proof cable. If not it will never work perfectly. I purchased two sensor for over tank and lower tank. I am going to change the sensor wires myself.
Dear Bishwnath Issue highlighted by you has never come to my notice with over 110 Dealers selling the product all over country. And I feel this could be due to quality of sensor's float bulb and the weight that we tie to keep the cable straight. Volume of float bulb is so designed that it can very well take the load of cable.
Pro's: This simple float control is very easy for installation and easy usage, Con's: electrical 230 Vac is protected with the sensor plastic, cable to run from motor to sensor. If there is any wireless way to transmit and receive the contact sensing it will be safe. it is apt
Hello Sir, in our system we use this float switch through our control unit, in which we don't route 230V AC through this cable float switch, its only a low voltage signal which is routed through this device. So it becomes very safe. Regards Team-SuperSync
Sorry , But in your website below, www.supersynctech.com/cable-float-switch-model-wls-02/ point 2 and point 3 it is Mentioned as 250Vac Rated voltage 10A rated Current@ 230Vac. and this Is still hazards. can you clarify this
So if the video include along with the controller it would be off sufficient , any ways if it low voltage & safe its good. Is there possible for a wireless feature in your controller that would be more preferable. Thanks for your swift response.
Thanks for your interest. This sensor comes with a controller to control your motor operation. Please visit following link for detailed description about this product: supersynctech.com/water-level-controller-model-wlc-dr-wlc-sr/ You can also contact us at: sales@supersynctech.com or through Phone: 0141-2585451, 9887440077
Dear Sir I would recommend you to use our sensor once. We have installations more than 8-10 years old, and they all are working perfectly till date. The problem which you have faced is because of quality of sensor. Currently there are 100s of qualities available in market ranging from Rs. 100 to Rs. 650 per piece. Try our once, I am sure you will not face any such problem. You can contact us at :- 9887440077, 9414136077
Check continuity with multimeters. Use the two wires that show continuity when float switch gone down. And when up disconnecting continuity. U can use that two wires in your phase line of motor.
आपने जो प्रोडक्ट अमेजॉन यूट्यूब चैनल पर बताया है कृपया करके यह प्रोडक्ट्स वाटर लेवल का मरने पर बंद हो जाता है मोटर और खाली होने पर चालू हो जाता है कृपया करके यह बताइए यह प्रोडक्ट कहां मिलेगा और उसका पूरा एड्रेस बताइए धन्यवाद
Dear Sir Thanks for showing interest in our product. Please share your contact details, so that we can have a discussion on commercial parts. Regards Team-SuperSync
We supply this sensor. You can see our website link just below the video window. Go through the details and help us know your email id so that we can quote for the same. Thanks
Sir, Please share the quantity you would like to purchase along with your contact number and email id, we will submit our best offer for your kind reference. Regards SuperSync Technologies Pvt Ltd Phone: 9887440077, 9414136077
Wow very very simple and easy.
wonderful demostration. Excellent
Simple and straight to the point 👍
Best video of this kind, Good practical explanation well done, Good luck
Thanks once again 4 da smash hit work
Very useful - thank you!!
THANKS BRO FOR YOUR ILLUSTRATION
No doubt that you have made this tutorial very nicely & thoroughly but I have one question in mind, Is it possible to customize that level at the very top of the tank so that it switches off when the tank is filled completely? And is it possible to disable that automatic switch sometime in order to use excessive water flowing out from the tank pipeline for gardening purpose?
Yes you can customize upper as well as lower levels. Put the system in manul mode to use it for watering garden or washing car etc
Great!
This is the only video that clearly and fully illustrates the correct installation of this overflow switch. Especially the positioning of the weight and in English. Thank you
Great video thanks sir for that 👏👏👏👏👍👍🌹🌹🌹
Great job...
Excuse, Under what grounds do you put the WLC sensor at the bottom of the tank? I hear that it is not safe and it is not clean that the tank should get just empty. Is in this height the power energy saving eficient (saving your electric bills ?)
Sir, we don't put sensor at the bottom of the tank. We prefer keeping sensor at some 1 to 1.5 Feet above the tank base. In this video we have just explained the process of installation. You can adjust the height at your connivance.
I have a few question about the wire connected to the sensor!!I is it directly connected to the motor or we have another control circuit along with it....beside that,motor is located at ground level and the tank is at upper level so the water has to be pumped to the upper tank from lower tank ....i think a 25-30 ft wire is required from the sensor to the motor at ground level..thak you
Sensors are connected to controller and controller gives power to motor.
No need any controllers
You have 3 hands? Amazing..
do u install in Kolkata I have 1 unit requirements
Please what is the purpose of putting that thing
good video
I just bought the same product but having trouble while doing connections please guide me how to do
Nabeel Akmal You can install the same as demonstated in video, else please contact us at +91 9887440077 or +91 9414136077
Thanks.
can you make video to boost water pressure from tank to tap? If u do i am very thankful to u. or any one can suggest me device to boost pressure
You can use pressure pump for boosting pressure. They are readily available in market.
9142841703
Use single pipe to fill the tank and use the same pipe to withdraw water from tank when you switch n moter all air in taps goes out and side by side you tank allso get full. Use a T in boftom which put water from up side and take from bottom side or call me 8054399504
Thanks. Very easy to understand
My experience tells this product has some simple and serious error especially sensor part. At the time of empty over tank condition this sensor works nice. But unfortunately, this sensor switch off your pump in the mid way of filling over tank. it means your over tank will be never fill up to your certain marked level. The problem here is that, they have used heavy thick cable with sensor switch which itself creates load inside water to flip your sensor upward. Otherwise, the controller part is nice. So my suggestion is to change the sensor cable by using very light electrical water proof cable. If not it will never work perfectly. I purchased two sensor for over tank and lower tank. I am going to change the sensor wires myself.
yes absolutely ryt sir I agree wt u
Dear Bishwnath
Issue highlighted by you has never come to my notice with over 110 Dealers selling the product all over country. And I feel this could be due to quality of sensor's float bulb and the weight that we tie to keep the cable straight. Volume of float bulb is so designed that it can very well take the load of cable.
Biswanath Samantaray you have to adjust the level and counterweight of this float switch
Biswanath Samantaray naveen
malviya
Biswanath Samantaray
I want to know how to connect it to both in the tank and the wall
Thanks for your help.
Do we need to power on always
Pro's: This simple float control is very easy for installation and easy usage,
Con's: electrical 230 Vac is protected with the sensor plastic, cable to run from motor to sensor.
If there is any wireless way to transmit and receive the contact sensing it will be safe. it is apt
Hello Sir, in our system we use this float switch through our control unit, in which we don't route 230V AC through this cable float switch, its only a low voltage signal which is routed through this device. So it becomes very safe.
Regards
Team-SuperSync
Sorry , But in your website below,
www.supersynctech.com/cable-float-switch-model-wls-02/
point 2 and point 3
it is Mentioned as 250Vac Rated voltage 10A rated Current@ 230Vac. and this Is still hazards.
can you clarify this
Dear Sir
Please visit following link for details
supersynctech.com/water-level-controller-model-wlc-dr-wlc-sr/
So if the video include along with the controller it would be off sufficient , any ways if it low voltage & safe its good. Is there possible for a wireless feature in your controller that would be more preferable. Thanks for your swift response.
Dear Sir
I am sorry, we don't have an option wireless. We have only wired systems.
Regards
Team-SuperSync
Please explain full circuit installation from motor switch to sensor thanks
Water is clean 👍👍👌
where u get this sensor and what is the price
Dear Mr. Shukla
Please confirm are you a buyer or supplier of this product.
Regards
SuperSync-India
I am interested to buy this sensor for personal consume
Thanks for your interest. This sensor comes with a controller to control
your motor operation. Please visit following link for detailed
description about this product:
supersynctech.com/water-level-controller-model-wlc-dr-wlc-sr/
You can also contact us at: sales@supersynctech.com
or
through Phone: 0141-2585451, 9887440077
Sensor works perfectly for few months but slowly after 5/6 months the sensor is leaked or the switch inside is rushed and does not work properly.
Dear Sir
I would recommend you to use our sensor once. We have installations more than 8-10 years old, and they all are working perfectly till date. The problem which you have faced is because of quality of sensor. Currently there are 100s of qualities available in market ranging from Rs. 100 to Rs. 650 per piece. Try our once, I am sure you will not face any such problem.
You can contact us at :- 9887440077, 9414136077
Very nice
@@supersynctech Yes. Float switch should be good quality and IP68
HELLO
Rathore sab
My self kapil rathore ujjain
From where you are
Nice
Where I can get this sensor?
Ashish Srivastava
Will get online
salam sir
sir motor ke sath kaise isko connect karenge iske wire ko blue,black and brown please make a
video sir
Sensor is designed to be connected to controller and safe to connect directly to motor with high voltage. This could be lethal and might cost life.
Check continuity with multimeters. Use the two wires that show continuity when float switch gone down. And when up disconnecting continuity. U can use that two wires in your phase line of motor.
Super.
I have required this flot swich in 32 amp can available in market
Sorry Sir, we don't have float switch of 32 Amp.
@@supersynctech 32amp me aata h ki nahi
very nic
do u know the meaning of sensors?? where is sensor in this video..... this is called .. NO or NC float switch which switch pump motor off and on.🤗🤗🤗
We know that sir, but its mentioned in lay man's language so that everyone can understand. Not everyone is as technical as you Mr. Bhatti.
You are the legend of INDIA
Very useful. Thanks
Can I connect this switch with booster water pump instead pressure switch
good sar
Connection kon dikhayega
very nice
Love from Pakistan bro
Minilec wlc d1 connection to submersible starter kit diagram
OK bat small dot bhai o fail ho ko power tank mea sapllai hothoooo
tell me
आपने जो प्रोडक्ट अमेजॉन यूट्यूब चैनल पर बताया है कृपया करके यह प्रोडक्ट्स वाटर लेवल का मरने पर बंद हो जाता है मोटर और खाली होने पर चालू हो जाता है कृपया करके यह बताइए यह प्रोडक्ट कहां मिलेगा और उसका पूरा एड्रेस बताइए धन्यवाद
Thanks sir, please share your phone number our sales team will contact you.
Regards
Team - SuperSync
khotai pabo water cuntol choice
how to.make this device
that is float switch,
We know that sir, but its mentioned in lay man's language so that everyone can understand.
sir muje stater ka connection samjha dijiya
beautiful hkm
Abhimanyu Singh Rathore do you think it can work in hot water as well.
b
Cost of this
What's the cost?
Dear Sir
Thanks for showing interest in our product. Please share your contact details, so that we can have a discussion on commercial parts.
Regards
Team-SuperSync
Mujhe pta h yr
Please replay
Bhaya hindi me achha hota..
This is floating switch not Sensor
No need. You have to present the tools ans objects you use. I could understand nothing.
Are yaar je goron ki hi since hi or tum unko he bata rahe ho english me jarurat to hamko hai to esleye basha badl do
We supply this sensor. You can see our website link just below the video window.
Go through the details and help us know your email id so that we can quote for the same.
Thanks
Where is the link
I need one pice
Try to Improve the Tecknik..
It's not sensor. It's float switch
kine da ae 22
Sir, Please share the quantity you would like to purchase along with your contact number and email id, we will submit our best offer for your kind reference.
Regards
SuperSync Technologies Pvt Ltd
Phone: 9887440077, 9414136077
Very useful - thank you!!
Nice