You are awesome. I had a bolt that didn't go well so I needed it removed. Came to YT to see if a solution existed and found this video. Using the logic presented I was able to create a solution with the tools I had on-hand. It wasn't pretty but I was able to get the bolts out and continue with the project. Thank you so much. Your tool would have made life easier but I needed to get the job done same-day so I made it happen.
In the event that the cone broke free from the bolt shaft, what of tapping the wedge free of the sleeve with a punch and then fishing the sleeve and then the cone out with a hook or magnet?
Hi Jim, if the cone breaks off, it's tough to reuse the hole. if it pulled out a ways before breaking, that method would work well. It's more likely that it will break when first starting to pull in which case you likely won't have room to tap the wedge out to fish the clip. You can drill through these with the rebar rated masonry bits available from Hilti/Milwaukee (and probably others). this does use a lot of battery and goes through bits quickly. I try to be careful not to break them, and if they do break, usually patch the hole and drill a new one.
What application are you using them in? The hardness of the base material and brand of the anchor make a lot of difference. If wedge bolts won’t tighten down, sleeve bolts, or adhesive anchors may be a better option.
@@westernadventureinstructio9227 thanks, yes I think they would work best with pure solid concrete. I'm using them on a car port foundation. But it's this ytong concrete, not the real McCoy
It’s called a YABR. You can find some info on Mountain Project www.mountainproject.com/forum/topic/116158404/yet-another-bolt-remover They’re built in small batches, and we don’t currently have any available, but if you want to be on the waiting list you can fill out this Google form forms.gle/tCNEtCksPXstYFHx9
@@g5familymotorsports The spinner is made up of a 3/8x16 to 1/2"x20 adapting coupler nut which available from McMaster, and a sds+ chuck adapter which is threaded 1/2"x20 and available on amazon or AliExpress. together they're about $15
![Expansion bolts: Wedge bolt vs Sleeve bolt [Climbing bolt basics]](http://i.ytimg.com/vi/46CJWZYVSGY/mqdefault.jpg)
![Expansion bolts: Wedge bolt vs Sleeve bolt [Climbing bolt basics]](/img/tr.png)
You are awesome. I had a bolt that didn't go well so I needed it removed. Came to YT to see if a solution existed and found this video. Using the logic presented I was able to create a solution with the tools I had on-hand. It wasn't pretty but I was able to get the bolts out and continue with the project. Thank you so much. Your tool would have made life easier but I needed to get the job done same-day so I made it happen.
Where do you get the coupler?
In the event that the cone broke free from the bolt shaft, what of tapping the wedge free of the sleeve with a punch and then fishing the sleeve and then the cone out with a hook or magnet?
Hi Jim, if the cone breaks off, it's tough to reuse the hole. if it pulled out a ways before breaking, that method would work well. It's more likely that it will break when first starting to pull in which case you likely won't have room to tap the wedge out to fish the clip. You can drill through these with the rebar rated masonry bits available from Hilti/Milwaukee (and probably others). this does use a lot of battery and goes through bits quickly. I try to be careful not to break them, and if they do break, usually patch the hole and drill a new one.
Hoy to buy?
I expect to have the puller available again in the next few weeks, and they can be ordered here westernadventureinstruction.com/store-1
I've used these anchor bolts recently and have to say I don't like them. A few don't tighten and very difficult to remove
What application are you using them in? The hardness of the base material and brand of the anchor make a lot of difference. If wedge bolts won’t tighten down, sleeve bolts, or adhesive anchors may be a better option.
@@westernadventureinstructio9227 thanks, yes I think they would work best with pure solid concrete. I'm using them on a car port foundation. But it's this ytong concrete, not the real McCoy
What tools is that with the purple handle?
It’s called a YABR. You can find some info on Mountain Project www.mountainproject.com/forum/topic/116158404/yet-another-bolt-remover
They’re built in small batches, and we don’t currently have any available, but if you want to be on the waiting list you can fill out this Google form forms.gle/tCNEtCksPXstYFHx9
Also where do you get the spinner bit?
@@g5familymotorsports The spinner is made up of a 3/8x16 to 1/2"x20 adapting coupler nut which available from McMaster, and a sds+ chuck adapter which is threaded 1/2"x20 and available on amazon or AliExpress. together they're about $15