Found my answer here with your video. I was trying to check Amps on my space heater. I didn't split the wire so I was getting very low readings. Now I know my amp clamp meter isn't bad one. Nice video. Do play safe, I hoped the wire won't melt. 😁
I use an old extension I don't care about whose cable I've split! This way you don't have to split every appliance's cable when you want to test them. Especially handy for stuff where the two wires are into a full sleeve and not easily spittable
Thank you for your kind words. Someday I plan on building a workshop not just so I can have room to work on my projects but to also offer up a space to help tech people how to do all sorts of stuff. But until than I’ll continue to utilize the resources I have. Thanks for watching.
YES but really been 36 yrs more u use like anything u going to look and do better each time get rid fumbling , symbols , use car s everywhere , we have lot DC motors ,actualy i fool people think lm smart no just have good memory , SAFETY FIRST ,
Jus got one that does dc and ac amps and works as a regular multimeter also with a thermometer also so am still trying to figure it out. Thanks for the info about having to split the wires as i would have never thought about that
@@Jay-tr3px Good question. You can use the clamp meter function with your test leads plugged in. The test leads just don’t do anything since they are disconnected when place in the clamp meter setting.
@@MAGSHowToVideos Thank you for the quick reply 👍 I'm going to subscribe now! Thank you again . P.s. When I checked my electrical diagram indicating a circuit breaker rated 15 amps. Why does it have and extra numbers with it (15A/5KA)?? What is the 5KA indicate? And how do you fuse a step down transformer?
Thank you for watching. If you liked this video or have any ideas for other How To style videos you would like to see, please feel free to let me know in the comments below.
@@thomasstambaugh5181 I sold this clamp meter last year. If I can remember, I believe it was part of the “Live Wire” or low/high power reader that allowed you to detect if a wire was “Hot” (had power).
Easy. What you will have to do is remove the element and set your multimeter to your lowest setting for Ohms. If you only have one setting that’s ok. Touch one of the test leads to each end of the element. Test for continuity. If you don’t have continuity then you need to replace the element. If you do than you should get a rough reading of 30-100 ohms. If your reading is higher than that… there might be to much resistance and most likely will have to replace the element. I might put together a video on how to do this. Hope this helps!
Thank you! I didn't know that I had to clamp only ONE wire. I was about to render my fluke 902 as broken. Now I finally know how it works after 3 years of ownership. I feel pretty dumb. Altho in my deffence, I normally work on cars (DC) so I am a little ignorant when it comes to electricity in my home.
@@flyboybbq1718 yes I realized that mistake a long time ago haha. Sadly I lost the files I used to make this video when my computer cashed years ago. I have been thinking about remaking this video but just haven’t found the time to do that. Thanks for watching.
There are dedicated wire split units for testing. However, it can be cheaper to get a short, heavy duty extension cord and carefully split it (no bare copper!), like he did. Doing this at both ends and having a flat plug will help when measuring the current of appliances such as refrigerators where access is tight. Want more- research "inrush current", which is also a useful current specification, especially when sizing for a generator.
You can calculate watts by multiplying the amperage by the voltage using the formula W = A × V. Amperage is the current flowing through the electrical device or system, measured in amperes (A), and voltage is the voltage at which the electrical system operates, measured in volts (V). For example, 10 amps of current at 240 volts generates 2,400 watts of power. Hope this answered your question. Thanks for watching.
I started my solar panels with smart battery generator, and I bought this Vevor digital clamp meter T-RMS, 6000 counts, 600A Clamp Multtimeter Tester.....Sir what's does it mean by 6,000 counts? thank you.
That means you have continuity. The long beep means you are just holding the test leads against the wires and haven’t broken contact. The reason for a short beep in my video is because I just touched the wire quickly then took the test lead off.
Good question. The reason you want to test for Currant is so you can make sure you are getting the correct amount of Amps. Even if you have the correct voltage, if you Amp output is lower than what your device is rated for, you won’t have the power need for it to operate properly. I hope this answers your question.
Hahaha ya don’t repeat that. Usually I’m all about safety, however, this video was requested by a Subscriber so I quickly put this together in 30 mins not realizing the wire.
I’m so glad I was able to help. It always makes my day when someone leaves a comment letting me know that my hard work has benefited someone. Thanks for watching and Subscribing!
Yes I didn’t notice that when I was filming. I usually am all about safety. This video was requested by a viewer so I sort of rushed putting it together and clearly I wasn’t aware of my surroundings.
hints and tips dept here. please ensure your conductors are routed in such a way as to not compromise safety, avoid sharp corners when routing cables, chemical solvents and in this case high temperatures. There are others but we expect users of this dept to use a little sense to avoid gaining a Darwin award. just saying. have fun out there and stay safe.
thanks for your video although you made me very nervous for you not paying attention to the wires of the toaster which was about to go inside the toaster!!! and ... I hope you remembered to turn the toaster off at the end of your video!! Next time when you are done with the explanation with a connected electrical artifact disconnect it immediately!! and keep it away, to your right or to your left, as you continue showing the tool to your camera.
There’s nothing to this, right? Clamp around the insulated cord, turn onto amps? When I do this I get 1/100th of the reading I expect.. if I clamp down right in the insulated cord I get 1/10th of the expected reading. Pretty sure it’s just a cheap pos I bought from Amazon, so I watched this in case I was doing something wrong
@@regantupe8688 hahaha yep. It’s crazy the amount of people who have pointed that out in the comments. But that’s good. Means people are cautious and paying attention. I was in such a rush to make this video for a viewer, I didn’t even notice the cable placement until after I had filmed it. Do what I say and not what I do haha. Thanks for watching!
You need to spend your money elsewhere. Like buying a level so that you can mount your camera horizontal. And then you can use the extra money to get blinds that match...
This was a requested video from a subscriber. I literally filmed, edit and up loaded this video within like 45 mins after the request. It was for sure a rushed video. You can also see the wire hanging over the toaster which isn’t the safest thing. For the blinds well I rent the house so I don’t feel like spending my own money to replace them. I did just drop $3K on a new camera and accessories so hopefully future videos will look better.
Please get a wireless lav mic. You may have valuable content, but listening to you yell at the little mic on the camera from across the room is an unnecessary annoyance. They aren’t much money and your production values will soar.
I am? How so? If there’s a easier way I could have made this video I would love the hear it so I can improve on future videos. This video was rushed (put together and uploaded in 1 hr) since it was requested by a follower, but I think it came out simple and easy to understand. Again would love some feedback if you have any. Thanks for watching.
@@sandorebussolini you do know the whole point of using a clamp meter is to read Amps right? If you are trying to learn how to test for Voltage you can check out my other video “How to use a Multimeter for beginners” in that video I show the basics on how to test for volts, amps and ohms.
Thanks for this. We're working on our 67 Cougar and needed to learn how to use our clamp meter. This was really easy to follow.
Thank you, that was perfect. I couldn't figure out why I was getting zero when I had the clamp over both wires of an appliance.
Hahaha just did the same thing and felt a bit dumb 😅
@GuillaumeLajoie thanks for admitting it and letting me know I'm not the only one.
Its probably fairly common imo@@keithhansen3670
Thank you for actually showing that you can only check one side at a time on an ac circuit. No wonder my readings were always zero, lol.
You’re welcome. I to originally had that same issue. Took me a little while to figure it out. One of the reasons I made this video.
Found my answer here with your video. I was trying to check Amps on my space heater. I didn't split the wire so I was getting very low readings. Now I know my amp clamp meter isn't bad one. Nice video. Do play safe, I hoped the wire won't melt. 😁
I'm in the same situation. Lol.
I use an old extension I don't care about whose cable I've split! This way you don't have to split every appliance's cable when you want to test them. Especially handy for stuff where the two wires are into a full sleeve and not easily spittable
@@MattCantSpeakIt -good idea thanks.
Yep same
You must set up a workshop dude. Don't let your talent go to waste on us. Teach the young to carry on your good work
Thank you for your kind words. Someday I plan on building a workshop not just so I can have room to work on my projects but to also offer up a space to help tech people how to do all sorts of stuff. But until than I’ll continue to utilize the resources I have. Thanks for watching.
Bro, you're toasting the power cord... 3:30
I don't understand your comment..He was just measuring the flow
He's letting the cord slip almost completely into the toaster slot.
@@paulcarter2907 Look at the toaster (turned on) and what's on top of it... Heat goes up
I carry a short 12" extension cord that has a split. It was intended for appliances that cords are a little short. It works awesome for a clamp meter.
How exactly do you use it?
Thank you!!! I am not good with electricity... Finally someone explained how to use a clap meter to check for AMPs.
YES but really been 36 yrs more u use like anything u going to look and do better each time get rid fumbling , symbols , use car s everywhere , we have lot DC motors ,actualy i fool people think lm smart no just have good memory , SAFETY FIRST ,
Jus got one that does dc and ac amps and works as a regular multimeter also with a thermometer also so am still trying to figure it out. Thanks for the info about having to split the wires as i would have never thought about that
Thanks--short and sweet and to the point. Cheers!
what happens to a clamp meter wben testing current with the clamp and the probes are connected?
Thank you
@@Jay-tr3px Good question. You can use the clamp meter function with your test leads plugged in. The test leads just don’t do anything since they are disconnected when place in the clamp meter setting.
@@MAGSHowToVideos
Thank you for the quick reply 👍
I'm going to subscribe now!
Thank you again .
P.s.
When I checked my electrical diagram indicating a circuit breaker rated 15 amps.
Why does it have and extra numbers with it (15A/5KA)?? What is the 5KA indicate? And how do you fuse a step down transformer?
Thank you for watching. If you liked this video or have any ideas for other How To style videos you would like to see, please feel free to let me know in the comments below.
is this the same process for measuring in rush amps or is there a specific in rush setting?
Brave man. I wouldn’t hold a wire with 12 amps going through unless by accident.
What is the little yellow wire at the top of the meter (such as 1:47)?
@@thomasstambaugh5181 I sold this clamp meter last year. If I can remember, I believe it was part of the “Live Wire” or low/high power reader that allowed you to detect if a wire was “Hot” (had power).
@@MAGSHowToVideos : Sounds like a lead for an "NCV" measurement -- "Non Contact Voltage". I appreciate the quick response!
I have a Fieldpiece sc77 like yours. I'm trying to learn more about using it. I need to check a element in my stove. How may I go about it?
Depends on what you are trying to test in you stove.
The bottom element.
Easy. What you will have to do is remove the element and set your multimeter to your lowest setting for Ohms. If you only have one setting that’s ok. Touch one of the test leads to each end of the element. Test for continuity. If you don’t have continuity then you need to replace the element. If you do than you should get a rough reading of 30-100 ohms. If your reading is higher than that… there might be to much resistance and most likely will have to replace the element. I might put together a video on how to do this. Hope this helps!
Thanks
@@MAGSHowToVideos I also check for grounded element by touching one lead to the outer sheath of the element and the other to the power terminal.
Thank you! I didn't know that I had to clamp only ONE wire. I was about to render my fluke 902 as broken. Now I finally know how it works after 3 years of ownership. I feel pretty dumb. Altho in my deffence, I normally work on cars (DC) so I am a little ignorant when it comes to electricity in my home.
What about current polarity? How does it designate positive and negative current?
Fantastic video, thank you! Merry Christmas!! 🙏🙏
I was told to just bite into the wire to see if it's hot......the results were shocking
Alternating current, not alternate current. Video was useful. Thanks.
@@flyboybbq1718 yes I realized that mistake a long time ago haha. Sadly I lost the files I used to make this video when my computer cashed years ago. I have been thinking about remaking this video but just haven’t found the time to do that. Thanks for watching.
@@MAGSHowToVideos Sorry to hear that you lost the files. Big picture: anyone will understand your meaning.
Can I use this with a grounded cable or do I still have to split the cables? Thanks.
If you are trying to use the clamp, you have to have the wires split. Only one wire can run through it or you will not get a correct reading.
@@MAGSHowToVideos wow! Thank you so much for your help! I really appreciate your channel!
Can normal clamp meters measure voltage with the clamp?
The clamp portion on a clamp meter can only measure Amps. You would still have to prob the wires to test for voltage.
@@MAGSHowToVideos thank you very much for the response.
I wonder if you twist the wire 180 degree direction would it double the reading?
There are dedicated wire split units for testing. However, it can be cheaper to get a short, heavy duty extension cord and carefully split it (no bare copper!), like he did. Doing this at both ends and having a flat plug will help when measuring the current of appliances such as refrigerators where access is tight. Want more- research "inrush current", which is also a useful current specification, especially when sizing for a generator.
Good stuff.
Useful vid 👍
Out of curiosity, what happens when the wire carries more current than what you set for maximum?
You won’t get a proper reading… will most likely display “OL” on the screen since the measurement is to high to properly be displayed.
This video was uploaded in 2021 and it looks like it's from about 2009. This was helpful and informative but yeesh, the quality...
That’s weird I had 1080p available for this video. Thanks for pointing that out I’ll have to look more into why it’s no longer an option.
@@MAGSHowToVideos it is as an option and it looks like 240p or less. It's terrible.
how do you get watts?
You can calculate watts by multiplying the amperage by the voltage using the formula W = A × V. Amperage is the current flowing through the electrical device or system, measured in amperes (A), and voltage is the voltage at which the electrical system operates, measured in volts (V). For example, 10 amps of current at 240 volts generates 2,400 watts of power. Hope this answered your question. Thanks for watching.
@@MAGSHowToVideos Thanks.
Thanks, bud ..appreciated the tutorial!
You need an AC line splitter.
thanks man
You line up or center the wire ( the white wire for you) within the marks on the clamp ring for accuracy. Page 1 of instructions. 😢..
I started my solar panels with smart battery generator, and I bought this Vevor digital clamp meter T-RMS, 6000 counts, 600A Clamp Multtimeter Tester.....Sir what's does it mean by 6,000 counts? thank you.
what does it mean when it sound beep ? Long beep .
That means you have continuity. The long beep means you are just holding the test leads against the wires and haven’t broken contact. The reason for a short beep in my video is because I just touched the wire quickly then took the test lead off.
good clear video than you!
Thank you
Like your attitude
Why check the current only ?
Good question. The reason you want to test for Currant is so you can make sure you are getting the correct amount of Amps. Even if you have the correct voltage, if you Amp output is lower than what your device is rated for, you won’t have the power need for it to operate properly. I hope this answers your question.
Alternating current, not alternate. Also, it's a clamp meter, not a clam meter. Thanks for the video, very helpful.
Hahaha ya I didn’t even notice I was saying that until someone else pointed it out after I posted this video.
From 3:30 . I couldn't help but noticing the wire on top of a heating stove.
Hahaha ya don’t repeat that. Usually I’m all about safety, however, this video was requested by a Subscriber so I quickly put this together in 30 mins not realizing the wire.
Thank you 😊
The wire over the running toaster had me nervous 😅
Excellent tutorial, thank you. It's a big thumbs-up and a sub from me.
I’m so glad I was able to help. It always makes my day when someone leaves a comment letting me know that my hard work has benefited someone. Thanks for watching and Subscribing!
I was measuring both wires and wondering if my meter was faulty... luckily I didn't return it!
i can't believe you have the toaster 'ON' with live wires going across the top of it, not much thought on safety levels ehh 🤔🙄
Yes I didn’t notice that when I was filming. I usually am all about safety. This video was requested by a viewer so I sort of rushed putting it together and clearly I wasn’t aware of my surroundings.
@@MAGSHowToVideos mmm,,ohh ok, do stand in the corner with a pointed hat,,for a bit, a video on that would be awesome LOL
Care factor zer0, its not like the wires were bare ffs.
Gracias amigo
Alternate current?
Hahaha ya I meant to say alternating current.
good job
It's "alternating", not "alternate" current. The word describes how the electrons flow.
Hahaha I didn’t even notice I said it like that. After years of having this video posted your the first one to point that out. Good job!
hints and tips dept here. please ensure your conductors are routed in such a way as to not compromise safety, avoid sharp corners when routing cables, chemical solvents and in this case high temperatures. There are others but we expect users of this dept to use a little sense to avoid gaining a Darwin award. just saying. have fun out there and stay safe.
Couldn’t say it better myself… safety always comes first and if you’re someone without common sense this is not for you haha
High temperature, as in when he's roasting his lead wires over the toaster elements?
Thank you!!!
thanks for your video although you made me very nervous for you not paying attention to the wires of the toaster which was about to go inside the toaster!!! and ... I hope you remembered to turn the toaster off at the end of your video!! Next time when you are done with the explanation with a connected electrical artifact disconnect it immediately!! and keep it away, to your right or to your left, as you continue showing the tool to your camera.
👍👍👍👍👍👍👍👍
Probably good info in there somewhere, but the audio really is crappy. Could not watch much of it.
Ty
Thanks man
I'm such a boob. I couldn't figure out why my big appliances only showed around 0.3 amps when I clamped them. Now I know!
👍
Uh. Alternating current, not alternate current.
Hahaha ya to be honest I didn’t even realize I said it that way until someone pointed it out to me last week.
3:19 Damn, I thought my new clamp are broken.
There’s nothing to this, right? Clamp around the insulated cord, turn onto amps? When I do this I get 1/100th of the reading I expect.. if I clamp down right in the insulated cord I get 1/10th of the expected reading. Pretty sure it’s just a cheap pos I bought from Amazon, so I watched this in case I was doing something wrong
Tu écris en français ton slogan, par compte ton explication vidéo demeure Anglais.
You have to ruin your wire of the appliance to get a reading, that sucks man.
@@pilbomags488 not necessarily. If you use a extension cable that has wires you can separate like the one I used in this video you don’t have to.
I sell these items
Anyone else waiting for the cable to catch fire?
@@regantupe8688 hahaha yep. It’s crazy the amount of people who have pointed that out in the comments. But that’s good. Means people are cautious and paying attention. I was in such a rush to make this video for a viewer, I didn’t even notice the cable placement until after I had filmed it. Do what I say and not what I do haha. Thanks for watching!
You need to spend your money elsewhere. Like buying a level so that you can mount your camera horizontal. And then you can use the extra money to get blinds that match...
This was a requested video from a subscriber. I literally filmed, edit and up loaded this video within like 45 mins after the request. It was for sure a rushed video. You can also see the wire hanging over the toaster which isn’t the safest thing. For the blinds well I rent the house so I don’t feel like spending my own money to replace them. I did just drop $3K on a new camera and accessories so hopefully future videos will look better.
You need to get yourself a decent microphone
Ya I know… this video was sort of a rushed job since some have requested it that same day.
Please get a wireless lav mic. You may have valuable content, but listening to you yell at the little mic on the camera from across the room is an unnecessary annoyance. They aren’t much money and your production values will soar.
So, I'm going to make a tutorial about guitars. I don't own an electric guitar, just an acoustic guitar. But they're the same, right? 😂
You are trying too hard
I am? How so? If there’s a easier way I could have made this video I would love the hear it so I can improve on future videos. This video was rushed (put together and uploaded in 1 hr) since it was requested by a follower, but I think it came out simple and easy to understand. Again would love some feedback if you have any. Thanks for watching.
Just awful. You couldn't demonstrate voltage. I mean what's a more popular reading, amps or voltage ?
@@sandorebussolini you do know the whole point of using a clamp meter is to read Amps right? If you are trying to learn how to test for Voltage you can check out my other video “How to use a Multimeter for beginners” in that video I show the basics on how to test for volts, amps and ohms.