Wow, tottaly speechless, he should of just got his neighbour to operate the forklift, and as for the guy acting counterweight, you sir deserve to be flattend like a pancake
Never try to turn with a big load in the air. Back straight up and lower to the ground then turn. He made this hard on himself. The forklift is too small but s good operator could've done a much safer job.
if there was a list of 7 deadly forklift sins what you mentioned would certainly make the list... also the uneven, loose gravel ground wasn't much help either
First, check the load and confirm if your forklift can lift it. Ok so let's say you can't confirm the weight the fact that the back wheels are lifting off the ground means the load is too heavy. Turning with your load in the air is another no no. Guy climbing on the back of the FL is another no no.
Those loads are a pain in the arse. I had a few yrs under my belt before i started unloading similar loads and it takes a few loads to get the knack of.
They already have one. what they need is a forklift operator an operator would know the safety rules with operating a forklift and that his forklift would not be able to lift that load.
All the comments given are correct..in addition to the bad mechanical condition of the truck and the heavy loads which exceed the capacity of the forklift truck.
Heavy loads that the forklift cannot lift or have difficulty in lifting become dangerous as soon as it is loaded on its feet. The forklift operator should use the hydraulic arms calmly and touch sensitively. The truck driver has put himself in great danger here. Occupational safety is not provided in most places at world standards. If you notice, 7:21 does not fully enter the pallet. And the distance remains. Life is so short that you can't understand how it went.
Absolute idiot... I make lifts everyday that take me out of chart and more experienced operators I work with make picks more than id be comfortable with. But you put an idiot like that in a forklift without a load and he is going to kill some one. Holding the throttle wide open like and idiot...
lmfao you had me cracking up with this one, I drive a forklift in a warehouse for a living, everything that these guys did goes against operating one of these things omg
With an operator and not a driver this is a one-person job. Nice to remove the cover on roof of forklift. Pre covered units of plywood can be difficult but very simple. Ford slightly tilted, pick up on top of unit while driving in so you don't drive forks into tarp of bottom unit,
I think I’ve found the wrong video somehow I was only looking around because i’ve got my refresher tomorrow as a little reminder ffs.this should be used for beginners in the classroom lol
As a newly qualified 3 & 5 tonne forklift and a 7.5t sideloader operator (I won't say driver)...this made my brain bleed. The sausage struggled to get the first pack off and when he did, his arse was bouncing up and down... what did he think would happen with the second pack?
@@charlesnelson838 I've just watched this again with a few months hardcore liftyboi experience under my belt and honestly, I want to jump through the screen, slap both the idiots and do it myself. Lol...I've been told I'm not an operator anymore too. I'm a driver now! Woohoo! Haha!
Main problem is that forklift was not designed for loads that heavy. Worked in a lumber yard for 7 years operating forklift, anybody who would have attempted that would have been fired IMMEDIATELY. Had the pleasure of watching a co worker attempt to bring 20 ft wide load of lumber through a 16ft wide aisle by driving with the full bunk 30ft in the air over the racking. He tapped the brakes slightly to slow down, the entire mast twisted, swung the load, plummeted from the sky, and took out the entire aisle of cantilever racking. Needless to say he didn't come back.
When unloading, you lift the load, reverse back a little so you don't move the pack behind it, then tilt back. You then have your steering wheel straight, not turned,and gently reverse back, looking in the direction of travel. By reversing back straight, you can lower the load as soon as possible, as the lowest position is the safest. Humans should never be used as counter weights. Get a bigger machine! When you park it, forklift blades should be on the ground, tilted forward and handbrake on. If you're moving a tall load that restricts forward vision, drive in reverse. Just follow the logic.
no one gave advice to this driver, 1. the forks must go all the way under the load, 2. as soon as you lift a load, especially a heavy one, before moving, tilt the crane with the load towards you or as close as possible to the forklift, then the load will come on the rear wheels, 3. as soon as you move away, immediately lower the load as close to the ground as possible..
A for effort youngster. We all gotta start somewhere. Fortunately nobody got hurt. You just need to be taught some fundamental forklift safety practices and then it's just a matter of practice and time. Thanks for sharing!👍
one of his issues is he keeps cutting the wheels way too deep... look at the 6:22 mark... dude you ain't moving with the wheels cut that deep... he keeps killing the engine trying to move like that... same thing at the 8:38 mark, i mean dude what are we doing here?????
Is it the job safety video "How not to do it"? What a nincompoop! The neighbour doesn't seem to like his forklift. If he really is a carpenter, it's amazing that he is still alive.
Si la carga supera la capacidad del fort lifts.. no tienes cuando poder realizar el trabajo. Vi 4 errores....no te pusiste el cinturón de seguridad, dejaste subir a una persona al equipo, dejaste que una persona subiera al mástil y que pasara por debajo de las.horquillas
Definitely the owner, real forkie probably called in sick, and bro doesn't know how to drive manual. Literally had his foot down on the accelerator the whole time...wasted half a tank of gas with that driving. lmao
Olá está bem claro que carga ultrapassar os limites da empilhadeira. Ainda bem que nada aconteceu pois esse cara que subiu na máquina para fazer o contra peso correu um grande risco de se machucar feio
Guey no tienes que curvar mucha la direccion solo entra y listo con la llantas de la direccion rectas ese pedal no es el apropiado el que estas pisando con la pierna izquierda en el centro hay otro que tambien hace el mismo trabajo, y es mas seguro.
Really!!!!!!!!!! Dude had no bloody clue, I was actually yelling at the fucking phone, that was hard to watch, he made every mistake there was to make, FFS!!!!!!! Very irisponsible of the company, give the kid some training
Dónde le dieron la certificación a este operador claro si se le puede decir operador, lleva hasta la carga mal el tiene que bajar la carga inmediatamente y llevarla al raz del suelo!! 💀💀💀 Este hombre es un peligro!!
I saw a video where a load was to heavy and the back wheels went up and someone tried hopping on the back to weigh it down like in the video and they fell under and got crushed
![⭐️( ลอยกระทง 2024 ) Ver. แดนซ์ Remix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/rMWOLhgXUHc/mqdefault.jpg)
This needs to be turned in to a " shake hands with danger" training video.
Waa that originally a Union Pacific video?
😅 0:53 0:53 0:54
wow, this is painful to watch, seems the operator lacks the most basic common sense and understanding of mechanical dynamics.
He’s not an operator could never be
Lmao..yeah, frustrating lol.
Haven’t a clue
EVERYTHING about how they did this is just unbelievable!
Wow, tottaly speechless, he should of just got his neighbour to operate the forklift, and as for the guy acting counterweight, you sir deserve to be flattend like a pancake
Scary thing is........the other guy is normally on the road in a multi ton weapon 😬😲
The company does not know what trouble it is getting into with this forklift operator, which can cause an accident at any time.
Please do not operate any more fork lifts
You my friend take the piss out of us forkies , hope you don't handle your misses the way you handled the FLT 🤣😂🤣😂
When a german forklift driver reads „forkies“😂😂
Made my day
I love when I roll up to a place with some 4000 lbs pallets and buddy comes out in his little bobcat and I'm like yeah you're gonna tip.
Never try to turn with a big load in the air. Back straight up and lower to the ground then turn. He made this hard on himself. The forklift is too small but s good operator could've done a much safer job.
if there was a list of 7 deadly forklift sins what you mentioned would certainly make the list... also the uneven, loose gravel ground wasn't much help either
gravel isn’t the problem. It’s the driver.
He didn't even know which way his tires were turned. He couldn't perform the most basic of functions.
I saw the exact thing happen at a junkyard. Fork lift was pushed beyond its limit and it tipped over
First, check the load and confirm if your forklift can lift it. Ok so let's say you can't confirm the weight the fact that the back wheels are lifting off the ground means the load is too heavy. Turning with your load in the air is another no no. Guy climbing on the back of the FL is another no no.
You think they following osha rules ? They not even on a osha premises lmaooo
@@karlablanco6803 😆
Those loads are a pain in the arse. I had a few yrs under my belt before i started unloading similar loads and it takes a few loads to get the knack of.
Your dreaming…
Y'all really can use a forklift driver there ...lol
They already have one. what they need is a forklift operator an operator would know the safety rules with operating a forklift and that his forklift would not be able to lift that load.
@@charlesnelson838
If you don't know safe operating procedures and what the machine you're operating is capable of then....not an operator
@@charlesnelson838 exactly!
The forklift should have a weight com on the forklift. Duh.
@@joshuagarrett9371 Capacity plate; required by law on all forklifts, learn to read it.
All the comments given are correct..in addition to the bad mechanical condition of the truck and the heavy loads which exceed the capacity of the forklift truck.
agreed the fork probably hasn’t been taken care of very well
i almost fell in my chair when i saw u operate, be safe out there
your neighbour will love this video.
Best OSHA production I've ever seen, I actually thought these guys were real idiots.
Haven't laughed like that in ages..like watching the Keystone Cops..
Heavy loads that the forklift cannot lift or have difficulty in lifting become dangerous as soon as it is loaded on its feet. The forklift operator should use the hydraulic arms calmly and touch sensitively. The truck driver has put himself in great danger here. Occupational safety is not provided in most places at world standards. If you notice, 7:21 does not fully enter the pallet. And the distance remains. Life is so short that you can't understand how it went.
First day at work
Absolute idiot... I make lifts everyday that take me out of chart and more experienced operators I work with make picks more than id be comfortable with. But you put an idiot like that in a forklift without a load and he is going to kill some one. Holding the throttle wide open like and idiot...
Iam forklifter expert iam searching job europe from pakistan
The way he consistently bounces the pallet as if he wants to play teeter totter and see what goes flying off first
lmfao you had me cracking up with this one, I drive a forklift in a warehouse for a living, everything that these guys did goes against operating one of these things omg
Ala puta calle los mandaba yo por como se comportan trabajando están forzando la maquina
Which skill is worse developped? The one operating a fork lift or the one holding a camera?
With an operator and not a driver this is a one-person job. Nice to remove the cover on roof of forklift. Pre covered units of plywood can be difficult but very simple. Ford slightly tilted, pick up on top of unit while driving in so you don't drive forks into tarp of bottom unit,
Jadi operator Forklift jeli & hrs bs merasakan beban yg mau di bongkar , kl Forklift ga kuat jangan di paksa,q jg operator Forklift
I think I’ve found the wrong video somehow I was only looking around because i’ve got my refresher tomorrow as a little reminder ffs.this should be used for beginners in the classroom lol
As a newly qualified 3 & 5 tonne forklift and a 7.5t sideloader operator (I won't say driver)...this made my brain bleed.
The sausage struggled to get the first pack off and when he did, his arse was bouncing up and down... what did he think would happen with the second pack?
And turning the FL with the load in the air 🤦🏾♂️🤦🏾♂️
@@charlesnelson838 I've just watched this again with a few months hardcore liftyboi experience under my belt and honestly, I want to jump through the screen, slap both the idiots and do it myself. Lol...I've been told I'm not an operator anymore too. I'm a driver now! Woohoo! Haha!
@@BMVF_Ultra lol in the Osha course I was told I'm an operator but the word driver will be used as well
Main problem is that forklift was not designed for loads that heavy. Worked in a lumber yard for 7 years operating forklift, anybody who would have attempted that would have been fired IMMEDIATELY. Had the pleasure of watching a co worker attempt to bring 20 ft wide load of lumber through a 16ft wide aisle by driving with the full bunk 30ft in the air over the racking. He tapped the brakes slightly to slow down, the entire mast twisted, swung the load, plummeted from the sky, and took out the entire aisle of cantilever racking. Needless to say he didn't come back.
A lot of unsafe practices.. the load too heavy and center of gravity would cause the fork lift to tip over.. never allow anyone to stand on forklift.
They're both an accident waiting to happen
Or walk under the load
Yea, you seen he had 2 guys there for counterweight on the last bit 😂
When unloading, you lift the load, reverse back a little so you don't move the pack behind it, then tilt back. You then have your steering wheel straight, not turned,and gently reverse back, looking in the direction of travel. By reversing back straight, you can lower the load as soon as possible, as the lowest position is the safest. Humans should never be used as counter weights. Get a bigger machine! When you park it, forklift blades should be on the ground, tilted forward and handbrake on.
If you're moving a tall load that restricts forward vision, drive in reverse.
Just follow the logic.
no one gave advice to this driver, 1. the forks must go all the way under the load, 2. as soon as you lift a load, especially a heavy one, before moving, tilt the crane with the load towards you or as close as possible to the forklift, then the load will come on the rear wheels, 3. as soon as you move away, immediately lower the load as close to the ground as possible..
A for effort youngster. We all gotta start somewhere. Fortunately nobody got hurt. You just need to be taught some fundamental forklift safety practices and then it's just a matter of practice and time. Thanks for sharing!👍
This is a prank..really good one
one of his issues is he keeps cutting the wheels way too deep... look at the 6:22 mark... dude you ain't moving with the wheels cut that deep... he keeps killing the engine trying to move like that... same thing at the 8:38 mark, i mean dude what are we doing here?????
Is it the job safety video "How not to do it"?
What a nincompoop! The neighbour doesn't seem to like his forklift.
If he really is a carpenter, it's amazing that he is still alive.
Wow this forklift operator does know how to unload a truck and know his forklift capacity!! …. Too dangerous!!
Sometimes I'm the cause of the safety meeting. Sometimes I'm the only one dumb enough to do the risky stuff.
I look at guys like this handling a forklift and wonder how they are still alive
He’ll make an FLT driver when there’s feathers on the moon.
talk about the blind Leding the blind and i am not a flt driver and i was sweating just when he started
9:01 It seems the load is too big for that particular forklift. I suppose a bigger one had to get utilized.
Next time let a guy learn by having him pick up empty pallets and moving them around the yard. It's much safer and easier on your machine.
Would you mind shaking the camera a little more?
Nossa esse ta aprendendo ainda, vai com calma bro
Man who tough that guy how to drive a Hilo LMAO 🤣
Yes, he's not the best operator, but the main problem here is that the forklift is extremely small, and it's not capable to take such a heavy load.
driver is like mr bin😂😂😂😂
That guy has no idea on how to operate a forklift....
Esses não são operadores, são amadores. O rico está aí. Treinamento urgente e um padrinho experiente em empilhadeira.
I just got my certification and I know this is dumb.
Everything is bad he is not good driver
protip, if it starts to tip, just full send the forks down, safer then tipping
Inexperienced operator,1.5 ton max lift on truck,maybe near 2 ton load there,and he's over 500 mm on his load centre.
very nice video
both of them are unsafe...first day?
Dudes running under the forks😶
the driver is just learning to drive a forklift
and stands on forklift for counter weight are you fucking kidding me.... lloyd and harry got a new gig...lmfao
bet homer simson is the safety inspector
Tenho 30 anos nessa profissão e nunca vi tanto erro em uma só cena .mano do céu
This man should never have even got into the machine. An accident in the making. Not to mention damage to the lumber!
Ns ustedes pero para mí sigue siendo un principiante y que debe de conocer más sobre la grúa horquilla
Are this Laurel & Hardy the new Generation??
Meet the reason for your insurance premiums.....
?!?!?!?! You’re fired!!
Ha! maybe he should give it more throttle and turn the tires a little sharper lol.
That's the term accidental death mean anything to these guys everything that they did was wrong
and a forklift climb ...getting better....
Is this project really worth your limbs and/or life?
Por que se le apaga el montacargas?
Berapa ton itu mas ttp semangat sama 1 profesi pejuang 2 garpu
Si la carga supera la capacidad del fort lifts.. no tienes cuando poder realizar el trabajo.
Vi 4 errores....no te pusiste el cinturón de seguridad, dejaste subir a una persona al equipo, dejaste que una persona subiera al mástil y que pasara por debajo de las.horquillas
mexican paisa learning to drive a forklift like a champion
Hay mucha imprudencia y fata de seguridad,desde que comenzaron a descargar la carga.
Definitely the owner, real forkie probably called in sick, and bro doesn't know how to drive manual. Literally had his foot down on the accelerator the whole time...wasted half a tank of gas with that driving. lmao
He doesnt even need to use the left pedal to go forward he just jerking it back b forth like that lol
He should not be operating a forklift unless he knows what he doing there is to many dangerous things going on here both are at risk what they doing
Lucky to be alive
The fuck you even mean? Edify me.
Olá está bem claro que carga ultrapassar os limites da empilhadeira. Ainda bem que nada aconteceu pois esse cara que subiu na máquina para fazer o contra peso correu um grande risco de se machucar feio
How can this be possible??
What not to do as a forkie
Do you got forklift license bro
Guey no tienes que curvar mucha la direccion solo entra y listo con la llantas de la direccion rectas ese pedal no es el apropiado el que estas pisando con la pierna izquierda en el centro hay otro que tambien hace el mismo trabajo, y es mas seguro.
I can’t keep my eyes off the rear wheel positioning
Really!!!!!!!!!! Dude had no bloody clue, I was actually yelling at the fucking phone, that was hard to watch, he made every mistake there was to make, FFS!!!!!!! Very irisponsible of the company, give the kid some training
Someone could’ve really lost they’re life. Needs to be trained.
Good job.. 👍🏻
Dónde le dieron la certificación a este operador claro si se le puede decir operador, lleva hasta la carga mal el tiene que bajar la carga inmediatamente y llevarla al raz del suelo!! 💀💀💀 Este hombre es un peligro!!
Loads must be transported on VZV at a height of 30-50 cm above the ground. this guy obviously doesn't know.
Etwas blöderes habe ich noch nie auf einer Maschine sitzen sehen.
Bestimmt hat er noch ein Staplerschein
Lo que nadie sabe es que si atropellas o matas involuntariamente a una persona vas en CANA.No es un juguete es una herramienta con muchos riesgos.
I've never seen someone kill a forklift let alone3 times in 2 mins hahah
You can fix stupid... but you can medicate the hell out of it. Everyone involved are very lucky not to been injured.
I saw a video where a load was to heavy and the back wheels went up and someone tried hopping on the back to weigh it down like in the video and they fell under and got crushed
Beavis and Butthead lol 😁😆😂🤣
Forklift driver sathi job ahe ka
esto es real?
Lmfao I would have had that truck empty in 5min or less
Я думал, кто-то из них, до конца видео не доживёт.
Loading time back tyre not straight ,, It was a bad operating
Bro who tf let you on a lift.. I hooe in a year you got better lol that lift blew up 2 hours later 😂
That mdf is f**king heavy. You can’t just use any forklift to take that stuff off
Both these blokes are wasting good air.
👉 Operando GRÚA HORQUILLA / MONTACARGAS (Parte 2):
th-cam.com/video/gOpONJ8tRTI/w-d-xo.html