Nice video! Youre alot more gentle than i am. I dont rip them out or anyth8ng...but i dont baby hashboards anymore thats for sure lol. Ill add that all of the s19 miner variants, when putting the hashboards back in the case, each will go into the left-most slot in its respective area. I believe all of the s19 variants, and L7 variants...the hashboards will always go into the left most of the slot(i believe the inner hashboard theres 3 potential slots, outers each have 2). When looking from the back to put them back in, ill always slightly lean the boatd back as im lining up the slot...just a lil bit and line up the bottom front corner of the board with the left most(looking from the back as youre inserting)slot in the case. S19k pro might be different i havent really opened one up. KA3 i cant remember I may be wrong and its muscle memory at this point, and some variants i havent worked on in months(and i like that theyre not memorable because that means theyve been hashing like they should lol)...all s19 and L7 variants go into leftmost. Tedious small detail, but it can save a lot of time especially when starting out. If you forgot to take s picture or got sidetracked...dog ate your docuhomework lol.
For me I am getting “Network Status Abnormal”, I have tried updating the firmware also factory reset but still get the same issue. This machine is brand new I shouldn’t have to deal with the crap
How about s17pro repair? ... I bought 3 used ones a year ago, and they are all down. I am running two on hive firmware. I unplugged the boards to keep them running to the end, so now it is time to decide how to get them up... If No, can you recommend a west coast repair shop?
APW12 power to Hashboard 12-15V !!!! these contacts cannot shock when touched, the video talks about capacitors that can hold current, BUT the current is only 12-15 volts BUT with high amperage ...
Would try with a good control board. More than likely the hashboard will show up correctly. Again, hash boards rarely fully go out, its typically specific chips and/or temp sensor or incorrect voltage being read.
My s19j pro starts by showing all 3 hash boards, but then when it starts mining, it only shows hash board 3 mining. What could be the cause of this problem ? Any advice would be a massive amount of help since i spent a lot of money i saved up on this thing. Btw i bought it brand new. It was working fine for an hour, but then it started showing only hashboard 3. I updated the firmware to its latest 3 times, and i also tebooted it a couple of times. I also reset the setting and restarted the miner both via the plug and using the web interface. It still only shows hashboard 3 is mining.
I just got my first brand new asic, s19a pro 110th and it doesn't work. Abnormal Chips, abnormal worker 1,2,3, Network abnormal. Fans work but unajustable. Long term, the red light stays on "flashing" after it "settles". I restarted, factory reset "manuel and interface", SD flashed it, psu tested: pass, wires, don't know there brand new, Updated/upgrated, watched BBT, SOAT, RPM, Hobbyist Miner the list goes on. You mentioned i can get a board for the s19 pro, i don't see it. Maybe do a broken asic and troubleshoot a bunch of them : ) Thx man thought this was the video... maybe next time.
APW12 power to Hashboard 12-15V these contacts cannot shock when touched, the video talks about capacitors that can hold current, BUT the current is only 12-15 volts BUT with high amperage ... From life, if you used MIG welding, about the same thing - welding at 17 volts but with high amperage! ---- what I heard in the video regarding the electric shock from touching the contact bus shows illiteracy ....
@@BitsBeTrippin I'm not in position to give advice but I will give one anyway because internet, duh. You could make "review" products videos even without the physical products by your chrisma alone and I swear it will get views. Or just weekly price check or something like it. I'd enjoyed your works even tho I just found you today. I literally watched nearly all of your most popular vids.
Nice video! Youre alot more gentle than i am. I dont rip them out or anyth8ng...but i dont baby hashboards anymore thats for sure lol.
Ill add that all of the s19 miner variants, when putting the hashboards back in the case, each will go into the left-most slot in its respective area. I believe all of the s19 variants, and L7 variants...the hashboards will always go into the left most of the slot(i believe the inner hashboard theres 3 potential slots, outers each have 2). When looking from the back to put them back in, ill always slightly lean the boatd back as im lining up the slot...just a lil bit and line up the bottom front corner of the board with the left most(looking from the back as youre inserting)slot in the case.
S19k pro might be different i havent really opened one up. KA3 i cant remember
I may be wrong and its muscle memory at this point, and some variants i havent worked on in months(and i like that theyre not memorable because that means theyve been hashing like they should lol)...all s19 and L7 variants go into leftmost.
Tedious small detail, but it can save a lot of time especially when starting out. If you forgot to take s picture or got sidetracked...dog ate your docuhomework lol.
Don't forget to put an oil catch on the air compressor line if you're using it on electronics.
For me I am getting “Network Status Abnormal”, I have tried updating the firmware also factory reset but still get the same issue. This machine is brand new I shouldn’t have to deal with the crap
Try a new control board. What does your miner log say? Visit our site and open a ticket if you need further assistance
How about s17pro repair? ... I bought 3 used ones a year ago, and they are all down. I am running two on hive firmware. I unplugged the boards to keep them running to the end, so now it is time to decide how to get them up... If No, can you recommend a west coast repair shop?
I added a dual stage filter to my farm and it has saved me from ever cleaning my asics.
Search👆👆👆this name I pointed he will help you out..
What size farm/how many machines? If you're still mining....been a year since your post. A year in crypto. U know why I'm saying it like that lol
So did it run??? Common what a cliff hanger.
Yes! Should of included it running.
APW12 power to Hashboard 12-15V !!!! these contacts cannot shock when touched, the video talks about capacitors that can hold current, BUT the current is only 12-15 volts BUT with high amperage ...
Were these mostly the ASIC's from China when they shutdown mining?
First class thanks bbt!
top vídeo
can a hashboard show as a fault if the control board is faulty?
Would try with a good control board. More than likely the hashboard will show up correctly. Again, hash boards rarely fully go out, its typically specific chips and/or temp sensor or incorrect voltage being read.
@@BitsBeTrippin it does show but disapears from the dashboard doesn't stay very long mind.
Bhai tera number diye miner repair krwana hai ...where u from?
My s19j pro starts by showing all 3 hash boards, but then when it starts mining, it only shows hash board 3 mining. What could be the cause of this problem ? Any advice would be a massive amount of help since i spent a lot of money i saved up on this thing. Btw i bought it brand new. It was working fine for an hour, but then it started showing only hashboard 3. I updated the firmware to its latest 3 times, and i also tebooted it a couple of times. I also reset the setting and restarted the miner both via the plug and using the web interface. It still only shows hashboard 3 is mining.
Maybe you need to learn the basics of s19j pro yourself and take the time to look at courses or something
like it man keep it up
I just got my first brand new asic, s19a pro 110th and it doesn't work. Abnormal Chips, abnormal worker 1,2,3, Network abnormal. Fans work but unajustable. Long term, the red light stays on "flashing" after it "settles". I restarted, factory reset "manuel and interface", SD flashed it, psu tested: pass, wires, don't know there brand new, Updated/upgrated, watched BBT, SOAT, RPM, Hobbyist Miner the list goes on.
You mentioned i can get a board for the s19 pro, i don't see it.
Maybe do a broken asic and troubleshoot a bunch of them : )
Thx man thought this was the video... maybe next time.
You didn't looked for the warranty of Bitmain?
@@xiaoxiaokaty8299 i found the problem.
@@yvonnadeau2331 cuál era el problema??
@@inespalenzona2995 PoE switch, it cannot be used due to Power coming out and can fry the board.
@@yvonnadeau2331 pero arreglaste el problema o no ??? No lo pudiste reparar...no estoy para bromas
So, could that 'bus-bar' shock you?
APW12 power to Hashboard 12-15V these contacts cannot shock when touched, the video talks about capacitors that can hold current, BUT the current is only 12-15 volts BUT with high amperage ...
From life, if you used MIG welding, about the same thing - welding at 17 volts but with high amperage!
----
what I heard in the video regarding the electric shock from touching the contact bus shows illiteracy ....
Man... What happened to your channel.
Been busy - lots on X vs TH-cam these daya
@@BitsBeTrippin I'm not in position to give advice but I will give one anyway because internet, duh.
You could make "review" products videos even without the physical products by your chrisma alone and I swear it will get views. Or just weekly price check or something like it.
I'd enjoyed your works even tho I just found you today. I literally watched nearly all of your most popular vids.
All that wasted time watching and you didn't even show or say it is working!
@Bits be Trippin' ㊉①③④⑥④⑥②④⑧①② People watch out for this scammer!
First