How to Clean Sticky Rubber Plastic From Logitech Remotes or Other Electronics
ฝัง
- เผยแพร่เมื่อ 9 พ.ค. 2021
- Cleaning the sticky rubber that comes from older electronics isn't really that hard if you use the right solvent. Acetone based nail polish works wonders on sticky logitech remotes, sticky logitech mouse, sticky logitech keyboards. The plastic residue will come off with the right solvent =)
Do this at your own risk, liquids may cause damage to electronics if you are not careful.
★ How to Remove and Clean Sticky Keys on Macbook Air Step by Step Repair - • How to Remove and Clea...
MUSIC------------------------------
chill. by sakura Hz / sakurahertz
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/chill-sakuraHz
Music promoted by Audio Library • Chill - sakura Hz (No ...
Tags:
how to clean sticky rubber plastic ,remove sticky residue from plastic, removing sticky residue from plastic, sticky remote, sticky remote rubber, how to clean sticky plastic remote control, sticky logitech, sticky logitech mouse, sticky logitech keyboard, sticky logitech plastic, clean sticky rubber surface, clean sticky rubber coating, how to clean old rubber that is sticky, how to remove sticky rubber coating from mouse, clean sticky keyboard, clean sticky mouse plastic - แนวปฏิบัติและการใช้ชีวิต
please don't use nail polish remover! do not follow this video! you will ruin your items! Use 70% alcohol instead, it's more gentle and won't damage them.!
Let me pin this to warn the others 😱
@@thecollegepicker Acetone dissoves ABS-Plastic, is what hes saying.
ABS is really easy (cheap) to produce so many things are made from it.
I agree with Gothic. Before I tried looking up a video, I had over 20 restaurant serving spoons with this problem so I tri3d 4 things myself first. I did vinegar, hot water & soap, gasoline, and I even flex sealed 1 set to see if it held.
But the first 3 didn't remove sticky at all. I saw Gothics comment above and tried alcohol, and it was just seconds of alcohol and green abrasive 3M pad and all stickiness was gone. Thanks for that. I wouldn't have tried acetone either because it eats plastic and turns it in to a mush. So you are wiping off layers to get the result but yeah A+ comment about the alcohol. Now I can sell these things on Ebay. Yeay!
Fully agree with this. 70% alcohol with cotton pads. Steel wool to finish.
Thanks for this video. I used acetone and a cloth and procedure as advised, but even after a lot of rubbing, the plastic was still sticky and looked terrible. I then decided to try a fine steel wool ball and rubbed it until the surface looked smooth and good. I also rubbed the steel wool on the shiny plastic parts affected by the acetone, and this cleaned up brilliantly with no scratches. After completing the above, I applied some oil spray to enhance the plastic's colour and sheen. The remote looks brand new now.
Acetone degrades rubber/plastic which makes it worse
That was the best solution in my experience. Thanks for sharing. I used goof off with the fine steel wool and a magic eraser to clean up after I was all done.
My solution for a Logitech MX1000 mouse with that sticky degraded rubber goo was to take the mouse apart and scrape all the thin rubber coating off with my fingernails. It took a lot of work but I was afraid to use acetone. Rubbing alcohol and a cloth helps rub the last 5% off. Then I use a polish called PEEK Which is made for metal like sink faucets but it works great on hard plastic also. Shines it up nicely.
@@Earthneedsado-over177 oh my god the sheer amount of PATIENCE you have!
any suggestion on stcky rubber grip?
This is not a circumstance of people just having dirty sticky remotes. This is something from the factory on these remotes. I bought a brand new unopened Logitech remote that was 15 years old. Right as I touched it for the first time it was super sticky on the back. So it’s something they use in the manufacturing process. Thanks for the video. I’ll do this on my BRAND NEW remote :/
They're using the same rubber material on their flagship mice, and they're aware of the issue... Go figure
@@HamedEmine oh geez
How else are they going to get you to buy new products every couple years? 🙄
@@Brudergaming well, in their defense I have a remote from them that’s lasted many many years. So I guess it’s just a manufacturing flub.
Yes, this coating is used to give the plastic a leather satin feel. After many years, it breaks down and gets sticky.
It is also happening to the coating on my car dashboard.
Thank You! One of my Bluetooth speaker body was suffering this sticky surface over it & the acetone rub left it non sticky & shiny as a charm. Saved me from the realization of the sticky feeling and the device now looks shinier than before. Really a gadget saver trick!
I found that for stubborn surfaces, a nail guard sponge worked well; where I first used the scotch bright side (w/ acetone) to rough up the rubber surface and then the sponge side to clean up.
Thank You!! Was just about to toss my Harmony One before I saw your video! Feels like new now. Thanks again! BTW, another option is to remove the rubberized grip area from the remote (easily pry off) and then clean and reinstall. You could also try this approach if you wanted to remove ALL the coating down to the base plastic layer which is what I will probably do when my coating becomes sticky again in the future.
Thanks! Exactly what I needed to know. I had sticky residue on a Guitar Hero guitar that would not come off even with goo-gone. This worked great!
You are welcome.
OMG...this really works...somehow a rubber band got caught on my toaster oven tray and I didn't realize it until I had already put it in the oven to cook something...finally noticed melted rubber band on the metal tray and a couple spots in my sink where I had put the tray...picked off whatever rubber band I could then I used the nail polish remover with acetone and a streak free mirror cloth...worked excellent...thank you so much!!!
I had no acetone. But alcohol worked just fine. It’s all about the cloth used. Thanks bro
Alcohol is better.
worked really well on a plastic phone case with a strong dish scrubber, thanks!
Thanks! This worked great for an old F710 controller. Took about 30 minutes, did not have acetone, but rubbing alcohol worked great.
Update- I hesitantly tried the acetone and as expected it removed the sticky top surface but ate into the plastic creating more of a mess. It reminded me of using Testors glue on plastic models. So I used alcohol to stop the process and when it dried I scuffed the plastic with a burgundy scotchbrite and painted it. This was on a Denon remote controller.
Wow just restored an 8 year old Decus gaming mouse to it's former glory...great informative practical video. Thank you from South Africa
Thank you so much for this so helpful! ❤️❤️❤️
I have thrown stuff like this away, good to know. Seemed to be a quick process too. This was helpful.
You are welcome. This one was pretty fast!
Thanks for sharing this technique. Next time I have to clean a sticky remote, or some sticky plastic computer accessory or other souvenir from my youth, I will use your technique to get it cleaned. Afterwards, I'm going to try wiping it down with 303 Protectant, which protects all types of automotive and boat plastics exposed to,the elements, and may offer some protection from keeping the stickiness from returning to the plastic household items that are cleaned your way. Thanks again.
P.S. Some nail polish remover is not acetone based, or not 100% pure acetone, unlike the pure Acetone in the cans sold as a cleaning solvent in the paint sections of big box stores and in stand-alone paint or hardware stores. If you can keep those cans sealed, the stuff will last forever. By the way a solution of 50-50 acetone and ATF is one of the best penetrating lubricants you can use, but it tends to separate when left alone, so you mix only what you can use that day and you have to shake it up before you squirt it on whatever is stuck or needs lubricating. Any brand of ATF will work.
Thanks, worked perfectly for the sticky backside on my Harmony 1100.
As the last step I used a soft cloth and wiped the unit with surgical spirit. This to avoid possibly long lasting effects from acetone.
Eric bringing energetic and helpful vibes ! Always happy to see your content !
Thanks man I appreciate it 🙏
@@thecollegepicker 🤩🤩
Dear College Picker, your acetone/nail cleaner hint has just saved my bacon. I have a pair of very expensive hand-held wireless microphones that I will be using tomorrow for a high-paying client. The mics had been getting stickier and stickier and when I checked them just now, they were horrendously revolting to the touch. I used a tightly woven sock and the nail remover. They now look like new and feel better to the touch than they did when I bought them! I followed the acetone up with alcohol and polished them up with the socks. They look and feel great. A thousand thanks.
That's awesome to hear. I'm glad your high paying gig will be top notch now 🤝
Worked! Thank you. I thought I was going to have throw away a clicker for presentations but it cleaned up beautifully!
Glad it helped!
I have a Targus Bluetooth mouse with a sticky rubber issue. I used a vinyl and rubber trim cleaner for cars. The only listed ingredient was Naphtha (Petroleum) Hydrogenated Heavy. It took a bit of rubbing like you said, but it's not sticky and comfortable to use now. ☕😃👍
Thank you so much! These Harmony remotes always seem to come like this. You have saved me a lot of grief! TY
You are welcome. That gunk can get nasty!
i have an old wireless mouse from logitech and was wondering why it was so sticky. i thought that maybe i had put some duct-tape over it at some point, but now i know. gonna get some nail-polish remover and give this a try. thanks!
Thanks for that. I just tried it with Acetone Free Nail Varnish Remover. It worked fine. Just saved me £50.00 for a new remote. Thanks.
You are welcome 🙌
Thank you. Worked great!
Rubbing alcohol works also but requires a lot of work, rubbing in one direction. It is also less toxic.
The miscreants that design plastic to degrade, so that the consumer must spend more money, need to be flogged.
What worked best for me and this was for some super caked on stickiness, first I used a couple lysol wipes and a slight bit of elbow grease to wipe off the majority of excess until there was basically just a layer that kept getting moved around instead. Once I got to that point I switched to a microfiber cloth and some rubbing alcohol and it came right off.
I used yours for the normal plastic, and the acetone for this more rubbery plastic on my little speaker, so both worked amazingly, so thank you
I know this comment is old, but after getting most of the residue off with the acetone (there was still some stickiness), that 70% alcohol clean and dried it wonderfully! ❤
Followed your advice - thanks job is done got rid of the stickiness well explained ❤❤
Many thanks for this video. I have many sticky substances like this that I've just about given up on.
I’m blown away! I was not a believer that would work for the disgusting back of our remote……. It’s like new in 5 minutes! Thank you!
You are welcome 🤠 happy to help 🤝
Thanks, About to try. This was EXACTLY the remote and issue I had. Spot on.
I tried liquid dish soap, citrus hand cleaner, then tried alcohol, then spray adhesive remover. Nothing worked. So I will give the acetone a try and thank you in advance. Since the acetone is removing the softened layer of plastic I would expect the plastic coming off will clog the rag pretty quickly so turning to a fresh spot seems necessary. Thanks for the video. Cheers.
I was cleaning out my office and found your video. I tried with the acetone and it was a huge mess.
ALTERNATE METHOD: The Harmony One's back (disgustingly sticky) cover can be taken off completely. In this age of fixing iPhone screens, I thought this had to be possible and it was. I took my fingernail and pried the top edge on one side. It came up pretty easily. I proceed to do the same with the other side. I have an iFixit spludger (the long pencil thing with a point on one end and an tapered edge on the other) from a previous iphone fix. Once I got the top two edges loose, I pried down each edge. I could hear that there was some sort of tape holding down the bottom edge so once I loosened the edges the best I could I jammed the spludger, tapered edge first from the top to the bottom. I wasn't that gentle with it, so do at your own risk. The adhesive at the bottom of the back plate popped free and off it came! WARNING: there's a clip on the back plate near the bottom that may get broken in the process. Mine broke, but at least it got rid of that horrible sticky back plate. I will continue with the acetone trick and maybe replace the back, but for now I'm happy using it without the back. BTW it is solid plastic underneath so no electronics are exposed.
Thanks for this. I have several small electronics that have this sticky serface and it drives me crazy. I will try this tonight.
On my older Harmony remotes I've removed the sticky material with Goo-Gone. Will not etch the plastic like acetone will. Will require some pressure when rubbing it off. I will soon have to do this to my newer Harmony remotes as they are starting to feel sticky. The newer ones are approaching 5 year of age and sure enough is right around the time this rubber degradation occurs.
Is it fine to use on outside the straightener??
Dude , game changer. I’ve had this issue with ps2 thumbsticks and had to replace the sticks. Thanks for this
You are welcome Tom. I know exactly what you mean with those nasties!
Never knew there was a fix. Thanks for the awesome content.
You are welcome. Thanks for watching 😊
What is that blue project board you are using?
Oil may work for those who find that acetone doesn't work. Makeup brushes have the same problem and I used mineral oil and a used fabric softener sheet and that worked really well.
I'm having this exact problem with my iT Cosmetics Velvet Luxe brush handles, smh
Right. I think the coating is an oil-based rubber that is breaking down so I think the standard way of dealing with that is another oil and then probably like Dawn to flush it all away.
Have a pair of 20 X 80 binoculars, the ends that surrounds the "large glass" (Objective lens) became very sticky. From the ring that holds them to tripod brkt. to the edge of large glass is about 2 i/2 inches wide then is circular around the glass lens. I put the rubber seals over the glass lens to protect them. I used an old cotton T shirt and 91% isopropyl rubbing alcohol. Worked perfectly.
Thank you very much..work great..on the handle of my curling iron that who knows what made it sticky..👌👌👌
Did the acetone affect your plastic at all later?
THANK YOU 😊 I just bought a new in the package controller and it was super sticky.
Super helpful, I need to clean my plastic mac cover today! Thanks
You are welcome 🤠
Thank you for this video I needed it 💯
You are welcome
Another less toxic solvent is eucalyptus oil it's a natural sap oil from Australian Eucalyptus trees . It also strips off that sticky layer when plastic surfaces deteriorate . I saved my $400 RayBan's because the arms were going all sticky even the optometrist could not fix them . Eucalyptus oil fixed it right up . Scrub vigorously with cue tips and soft cloths soaked with the oil and the original smooth surface reappears like magic .
Maybe you were sold knock-off Ray Bans? Just wondering.... The plastic degradation that causes the stickyness is mostly from recycled plastic material. Virgin plastic wont do this. Cheers.
Worked perfectly! Thanks so much! I was ready to chuck out my Harmony One, but now I have a brand new feeling remote again!
You are very welcome. Happy Thanksgiving 🦃🤠
What is that blue tray in the background??
Dude, I owe you many thanks, I restored a very expensive 3DConnexxion device with this tip, works like magic. Cheers.
Happy to help 🤝
I have this battery powered coffee stirrer that has this horrible rubberized ccoating on it an it has gone sticky. I ended up using hand sanitizer to get it off and it was messy. It worked though.
I know I'm commenting on a old video, but I found success with Rubbing Alcohol (70%), Magic Eraser, and paper towel. Acetone can eat away plastic, so I used rubbing alcohol.
1. Dip the eraser in alcohol and scrub an area for a minute or so. This softens the rubber soft touch coating.
2. Then get a paper towel with a little alcohol and rub the area afterwards to transfer the coating onto the paper towel.
3. Repeat around the different area of the unit.
Planning on purchasing some acetone this weekend and I’m hoping this will work on the grip of my Canon digital camera.
Good luck on it 👍 thanks for watching
Bro this thing works thanks man ❤
I have always used methylated spirits as it does not remove the logo or othe writing on the plastic.
What if cable wires get sticky? I have tried to clean them but it dosent work becuase they get sticky again after they dried. :(
Awesome, working 100%. Thanks 👍. Downside is the plastic become glossy.
You are welcome 🤗
Thank you. I need to do this for an old umbrella handle.
You are welcome. So many applications
Isopropyl alcohol works as well
I used acetone but it was a bit to aggressive so I opted for 91% rubbing alcohol. When using the acetone to start I etched the plastic translucent lens where the remote sends it's signal through by accident. There is a fix. I used White Diamond polish with a paper towel until it started to clear up pretty good then I finished it up the lens cover on my work paints ( while wearing ) part polyester and cotton. The lens cover looks brand new again. Most standard car waxes would get you in the ball park within a few minutes using careful effort.
Thank you!
I have a targus mouse that has this issue too! I used goo be gone by still have some residue on it.
Try something acetone based and you should be good 👍
BOOM great tute!
You should use Grammarly or some other spell checker, dude.
People, try 95%+ isopropyl (rubbing) alcohol first since it is less aggressive. If it doesn't work, try a drop of acetone in an inconspicuous area and verify the plastic is not melted. For instance, ABS plastic can be completely melted by acetone. That will certainly destroy your device.
I think the acetone melting the plastic is what gets it of of this remote. Lots of ways to do it 🤝
@MucaroBoricua I wish i tried your method. I tried the acetone and it completely melted my plastic. On a positive note, it did remove the stickiness. Oh well.
@@vflytrap7158, oh no. But now you know. Something similar happened to me before I learned about the power of acetone.
Another chemical mismatch that gets many people is cleaning acrylic with isopropyl alcohol. Iso destroys the molecular links of the acrylic polymer causing it to develop cracks and even crumble in your hands. I learned about that after destroying a nice brand new acrylic book holder, minutes after unboxing it. That really hurt.
Hello - but in your example the rubber coating is still present. If it had worked then the underside would be shiny like how it is in that small portion that seemed to have rubbed off from general wear.
I had a horrible sticky folding USB. I watched your video and on my desk was a bottle of lens cleaner the optometrist gave me when I got a new pair of glasses. I sprayed some on a microfiber cloth and the sticky came off quite easily. Still felt a bit sticky so I lightly sprinkled some talcum powder on it and wiped the powder off and now it doesn’t feel sticky at all.
well, i got one of them at a thrift store, i hadn't seen your video first, i used 91% isopropyl alcohol cleaned it off then a few hours later scrubbed in some vinegar.. it's now a bright glossy black, problem now is it's super slippery and smooth, i don;t know if that's how it's supposed to be lol.
Thanks a million!!! WORKS!!
Thanks 😊
I wonder if they use this material on purpose so the items themselves aren't technically broken but just awful and nasty to use, so people would prefer to throw it away and buy something new rather than cleaning it. I had this happen to so many tech items, it's unbelievable..
Planned Obsolescence in full swing
No, they make the plastic feel like satin leather for a few years.
WOW this did work and worked really well. Thanks!!! One thing is you need to be patient and I am not. I would say it took me 30 to 40 minutes to start seeing it work. I really went over it many times and tried to keep it wet but not soaked. I'd say it looks like new and feels fine. Shocked that Acetone doesn't destroy it.
It does destroy it, but just the surface, that the point 😂
Worked perfectly and easily - highly recommended!
Just got a new old stock 20 year old Gen 1 monocular and it is nasty . Total degradation but I will try this method and see what happens .
great idea
thanks!
Thnku very much... it's awesome 👌
You are welcome 🤠
Thnx bro
Best to just use 91% isopropyl alcohol for this. Acetone is way to harsh and my melt some surfaces, logos, labels, etc.
I used acetone the last time and I put a reminder sticker on the bottle that “It melts plastics.” Just in case that I was forgetful and tried that again.
I use ipa. It may take longer but won’t melt abs that is often used as a hard plastic.
Thanks man
Now my camera is all shiny and usable again
I used vitamin C Toner to reduce the look of fine lines and dullness, and it seems to do the job as well.
Thank you! This just worked on my Bluetooth headphones.
Some essential oils also work. Tea tree oil and lemon oil come to mind.
Haven't found acetone solution effective. I prefer to rub simple cornflour onto surface and brush off residue. As yet I've not needed to repeat the process.
has it resurfaced? just wondering.
Thanks so much.
You are welcome
If you use some solvent, such as, ethanol you can remove dirt but it remains sticky as long as you don't remove the plastic part completely off. My solution is just letting some crumbled cottons cover it, then it does not get sticky anymore.
I have two old cell phones with this and on one of them there are metal under it so I’m just scraping it off I lost the Verizon logo
Ps. I used Clorox wipes then a non fiber cloth and it does a great job
acetone works a lot better than rubbing alcohol, but yea mask off the area, it goes after abs plastic
Excellent video- brief, punchy and useful
Used alcohol on lots of qtips to revive my wii classic controller joysticks! Thankfully they weren't too far gone and seem good as new!
thank you!!
You are welcome 🤠
That's a very cool thing I'm going to use it on my Dell projector remote after 10 years it has started getting gummy like really bad I'll try that I got to get some acetone
Thanks
Acetone dissolves ABS wich coincidently is of the of most used plastics in consumer electronics. Please use IPA or denatured alcohol instead.
Thanks, I tried to remove the stickiness with alcohol, barley did anything. When I used acetone nail polish remove cloths, it took me less than a minute to clean it all.
You are welcome 🤠
This trick work for me thank u
You are welcome Syed 🤝
It works to me, thanks pal
You are welcome
thank you for the video! I'm gonna fix de sticky rubber from my lap. It really drive me crazy
You are welcome ☺️