ฝัง
- เผยแพร่เมื่อ 6 ก.ย. 2024
- Increase your speed!!! Without Buying HP Parts!!! Everybody: you must NOT keep your RPM's high for a long period of time if you have done this modification. Once your motor reaches high RPM drop it down lower and then up again!This is very important!!!
@ps3kid310 you can get even a 50cc but there are endless possabilities. the expansion chamber exausts are by far the best and also add allot of pep. you can get any 50cc engine of a used pocketbike. most of the time the bolt directly up. a bigger bore doesent always give you more power though. engine upgrades such as different jets, an ngk performance plug, and porting and polishing will take you much further.
it's probably the exhaust. Theres a little filter in all 2 stroke motors for the exhaust and when the filter gets all dirty with grim and oil then the motor will sound like its chocking when you rev it up. If i where you then id clean that out. And if that didn't work then keep it on half choke so some of the exhaust doesn't escape through the front because 2 strokes need to burn all of the fuel to keep going. Even some of the exhaust.
No it can not damage the motor because the throttle is capable reaching that far meaning that the carb. will be able to deliver the proper amount of air resulting the engine to perform accordingly.
This does not damage the engine. It just makes the engine make as much power as it was designed to do.
Hey there,
It could be your belt or chain that is seizing the tire.(So loosen it just a little bit. Not too Much!) But there could be something else. Check the shaft bearings. You may need to replace them or grease them up. We hope this will help you.
-The Mount Motor Support Team
wouldnt the engine wear out faster with the higher rpms?
It is not bad depending on how you use it. What that means is that you cannot abuse the throttle by increasing the throttle and keeping it at a high rpm rate.
That scooter engine is very similar to Tanaka engines which are used on BladeZ. Just follow the video and everything should work out well. Thanks for your comment!
This cannot hurt your scooter. However after you have adjusted the carburetor to this setting, you must not let your engine run at a high rpm rate for a long time. This can damage your scooter. You do not need to do this on a HP carb.
Wouldn't opening the throttle like that red line the motor?
thanks dude but thats just decreasing the life of the scooter so do you want 2-3 more miles or do you want your scooter to last longer? i guess it your choice
No. You must loosen the wire. I have only tightened it up to show what the difference is between the two.
i did this today, my scooter sounds like its going up fill full throttle just by pressing the the gas, So much louder and faster, LOVE IT! thnx guys, hope cops wont care xD
if you take of the exhaust pipe or muffler on the scooter is it bad for the engine??
You can listen to your engine's pitch and take a guess on how fast it goes. You can also get a speedometer.
You must grind it off with a rough rock or other hard material...but it is not recommended. This can result in throttle complications.
Check to see if there is anything obstructing the air filter or carb. If that is not the problem, let us know and we will help you further.
You should check your clutch spring and clutch.
u know the oil filter right next to the thing u were doin on this Video.. yeah does it have to be lose and spin like that or it has to be tight
Yes, they will fit. Just let us know which parts you wish to purchase.
Nice trick... about to try it on my xg-550 I just got. You know anyone that sells freewheels that don't break the first 5 minutes to a week or rideing them??
Is it possible for you to make a video of the scooter starting up...That will help a lot!
do you know if this works on mopeds?
@AAAAAAACCCCCCCEEEEE This is just a rumor. Scooter like these are made to handle these types of rpms. This BladeZ gas scooter has had this mod for over four years.
i just fill it up with nitrose lol
hey theres something wrong with my goped. its an old sport. when you start it, it will idle just fine. but when you give it gas, you can feel the strokes are more powerful, but it it stays at idle speed. and after you give it gas, it dies.
We have a video online explaining how to do that.
This can be used on all scooters. This is a BladeZ 40cc.
Maybe 2mph faster. You should feel a difference in acceleration. It is a quite faster.
They are all the same. We at Mount Motor like the UFO style for the cool look!
Click on one of the advertisements leading to Urban Scooters.
ok. now it wont start.
Do you mean you want to mount the pipe on?
This scooter has a Clutch belt drive system.
ive done tht ut ppl around my area keep saying it too load i made a silencer but it dnt work at high revs help if any solutions and if u want to see my goped look at my videos
so you lose the wire and then you tightened the wire ?
did you put on a bigger front sproket?
will this work on a goped bigfoot? i am getting one soon a was wondering.
its looks awsome but could it damage the motor? j/w
That's fine. Still make a video. We can tell by the sound what might be the problem.
@trebay101 if theyre Go-PEd branded, they dont break often, hte chinese stuff its a grab bag. sometimes yes, sometimes no.
Great video.im going to try it.
Yes it should work on that scooter.
You do not need to take anything off.
does this hurt the engine of your scooter, also i have i high performance carberater can this still work
you say no HP parts yet you have a velocity stack installed. do you mean no HP parts since hte vstack install?
very nice, im going to try this
The 35cc to 40cc engines should be able to fit.
did the tire pop or did u break the rim
Yes... It should work.
Sure.
Yes it should work.
can a G-SCOOTER handle this r will it make it go shitty?
The best performance upgrade is the X-Can and the HP UFO-Style air-filter.
They come with instructions.
i checked. the carb is fine, and the filters ok to.
Yes it does.
There was a pretty good difference in torque and Horsepower. Speed maybe went up about 2mph. Not a big deal, but torque and horsepower went up!
does this work on a 52cc racer
mine gose 35 to but what do u mean by abuse?
will it work with a g scooter
No you CANNOT BLOW UP THE ENGINE LIKE THIS. Many people say this but it is NOT true.
It should.
dude i have the same scooter with all racing parts and it does 45 or 50 on a straght GET THE RACING PARTS
It is very bad for the engine. PLEASE DO NOT ATTEMPT!!!
nitrose ? Don't you mean Nitro?
thats not good sounds like u have piston problem or u need a new carb
thanks bro
apperictie datt
@yamahonkawazuki Exactly!
37 maybe. Just remember: DO NOT ABUSE THE ENGINE!!!!
sweet
ok thanks
They are good scooters, but BladeZ and Go-Ped gas scooters are better built and faster.
ok ill have it up soon
try looking on ebay or craigslist. if you cant find one there, you might just have to get creative
BladeZ Moby S.
yah i can have it up in a day or 2
@vankernize123 Please check out our website.
Visit Mount Motor dot com for scooter parts.
Yes it should work.