Thank you for making these videos, I am just starting to learn about RGB pixels and their support products and your videos are the best I have found on the subject and thanks to you I hope to have a few RGB mini trees in my front yard next Christmas. Thank you again
When connecting power between terminals, for safety and consistency, BLACK WIRE is normally used for GROUND (or V-) and RED or WHITE (less common) for Supply Voltage (V+, or VCC)
I have a question?, I have a LED strip ws 2812 B 100 meters, a strip of two meters is attached to the wall, total 50 strips are attached, total LED is 6000, which controller will be used for this? That works with audio?
I see there is a voltage drop to the end of the strip, but how does adding a ground wire help? Isn't it that the 5V wire should also be connected on another place?
Yes, as well, and not just at the end of the strip. Power loss will always occur, it's just a matter of reducing it as much as possible. Of you connect extra wires for ground and +5v at the end of the strip, the highest power loss will be in the middle then. Question is if you are able to notice it or not....
I know nothing about any of this but I'd love to make one. So if I wanted to make a 10ft sign... would this be enough power. I would hook everything up the same? Thanks.
In your vid: The GROUND wire (green), which they should call the common wire (?), is connected to the aluminum chassis? And the blue wire is VSS, which they should call GROUND? And VCC is the black wire? Thanks! Where did you get the power supply, btw? I see a lot of them from China on eBay, but just wanted to know if I could order in the US.
Awesome video will help immensely once my T1000S arrives. Quick question do i need to have a dimmable power supply for the T1000 and my Strips both 12v
I'm looking to do this program on a DC system with 6v batteries and the ability to have 6v and 12v possible system. What are the key differences in the power supply I need to know?
We do not carry these strips yet, this video is for information only. Flexfire LEDs sells ultra premium LED strip lights.(Some of the brightest in the world!) Please visit our site.
Do you guys sell something comparable to the programmable lights here... I only ask because I am working on a project to build an LED display panel for a theater for their marque
Ben Schran Shoot us an email at info@flexfireleds.com and explain a little bit about your project. We would love to help and offer any suggestions or product we believe will make your project a success!
Does the pixel number on the Auto layout means "sections" or number of LED on the strip? I have a 5050 SMD300 strip, that on each "section" has 3 LEDs (each one is RGB). I mean, if I want 30*30 layout, do I need 30 sections or total of 30 LEDs on the strip?
Great videos, thank you! Hey, can you share any insight on clear LED screens? (typically seen on large applications so the resolution being very coarse aids in the perception that it's clear) How are they doing that, are they somehow placing the chips to the side of the screen vs. inboard next to the LED, as seen on your example strips? Wondering if you might know of a good source to find clear strips and/or screen? Thanks again.
Hi, i am trying to install the program and i'm folowing your video, i do exactly the same as you but the program open a window with an error and it don't let me to continue. Do you know what could it be? When i put new file the error appears. I've downloaded around 50 different types of the led edit and in all of them i have the same problem, if you can help me it will be amazing. Thank you
Hi can you please show me how to connect the strip one to the other and connecting to the remote. I am planning to fix LED strip on my stair if you upload detailed video it will help me a lot .thank you
Hi, first thank's for that video. I bought the Controller and 10M of the W2801. Now i have a problem with the power supply. Is 60Amp not a bit to much? Can someone tell me if 20Amp is also enough? Thanks! :)
Hi Ryan Thanks for 4 awesome and easy to understand tutorials. I am wanting to make a project very like yours but with two differences. First: I want the LED display to be fully mobile. (It's going to be a LED Flag, mounted on a carrying pole) Is there a way of running it all of a 12Volt battery ?? I can find 12 volt LED RGB strips online. But don't know if they are compatible with the T1000S and I would like to know if the T1000S will run on 12V only, with out a 5 V input ? Secound: I'm on a Mac computer. Do you know if there is a way to run "LED Edit 2013" on Mac OS X ? Or if there is a similar program for Mac ?? Thanks Peter
Hello, I liked your video and would like to do the same but I am wondering how many strips of lights you use of how many LED counts and did you plug all of them together (chained) to just one output on the controller? Thanks in advance
Man, what kain of strip of led did you use in your video? Because i bought this ones: RGB 5050 SMD programmable WS2811 light strip and i hava this question...
Can someone explain or give a link to something informative about why the wire connection is like this? He connects V+ to 5V and V- to GND. I don't understand at all why... I've always learned about DC having V- V+ and GND, but this setup doesn't make sense to me... (semi-newbie in LED lighting here)
Considering the voltage drop: why do you add a red wire from the GND of the controller to the GND of the end of the strip? I thought you would have added an extra black wire running from your Power Supply (an extra V+ port) directly to the end of your strip (on the 5V dot, not the GND).
I have ws2811 led strip lights and hc008 controller. I have connected 25 meters of strip lights. after 10 m the voltage drops and my lights don't emit all colours after 10 m. same like yours my strip lights also have arrow marks so that I don't power up the wrong side. however u connected the gnd wire to end of led strip going against the arrow direction. will this help me as well if I do the same
Shadab Khan: Did you find a solution? I have a similar question because I don't think he should be able to jump power by using the ground wire like he does in the video. From what I've learned, you should jump power using the 5v wire (makes more sense to use the power wire to jump power) and that is how I've done it in the few projects I've done. [From Power, I attach 5v to controller and to light strip; From Power, I attach Ground to controller and to light strip; From Controller, I attach ground to light strip]. I'm wondering if his ground and power might be switched and he doesn't realize, either because he mis-labeled or the Chinese controller has mislabeled its pins/ports? I've seen other T1000s with different labeling order than mine, so I wonder if some are mislabeled? Any electricians out there who know why he was able to jump with his ground wire? Is the video correct?
Good . We are professional manufacturer of addressable pixel led / led strips . I'd like to add you to my professional network on LinkedIn & facebook .
The reason you add the ground to the end is to reduce the effective resistance of the bottom half of the LED's. The same thing is achieved by adding an additional power line. If you do both, you could vastly reduce power inefficiency due to accumulated resistance, however, adding a second ground to the end of the strips is usually enough. AFAIK, these stips use a common rail that runs down the back of all the strips, and the LED's and controllers tap into it in parallel. The arrows have NOTHING to do with flow of electricity, but flow of data.
+microtruckerwg Hi there, thanks for watching our videos. We have upgraded our power supplies, Feel free to give us a call at 1-844-FLEXFIRE and we will be happy to assist you with the design of your project!
I bought 5 of these off eBay for $20.00 each with free shipping from Hong Kong, they are called "SUPERNIGHT 12V DC 30A 360W Regulated Switching Power Supply" and all 5 of them work fine, the only problem I am having is with the thermostats, I can't get the power supplies to run quietly. Anyway, as soon as I wire up and plug the units into an outlet (without even drawing a single watt of power) all of the fans turn on at full-speed?! I was told the fans are only supposed to come on when the units start getting heated, or begin reaching their maximum 360 watt loads, but now from COLD-START/ZERO LOAD?!? Why are the fans running at max speed ALL THE TIME? Constant fans running at full-speed makes these units super, super noisy! Do you know if this 'fans-always-on' issue can be fixed? I am running our office LED lighting system from these which are nowhere near the full 360 watt load (more like 120 watts) but the fans running at full force with even just 1 watt, makes every one of these power supplies unusable. :(
i have all the things on the video but my led strip is 12v-DIN-GND i have only 3 outputs and 2 wires goes out from "12v" and 1 wire goes out from "DIN" and 2 wires goes out from GND hmm
Can you explain what is the difference between the 3 wire (I believe Digital) to the 4 wire strips? & can you explain the differences in the WS28- models? Thanks Murf!
Hello Dan, sorry for the delay in response! One of our guys made this video as a helpful tool to answer some questions for some customers. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
LED strip dislay is one trend of LED display, it's much lighter than traditional LED dislay , low wind load and you don't need air-condition for it's not enclosed design. We worked with it for years , and we've developed some Series of the product . Pls come visit our website if you are interesting and let's together develop the technology .
Yes, but it is likely overkill for whites unless you have a project requiring each led to be programmable at different intensities (this set-up controls millions of colors and each led individually). There are much simpler controller/power set-ups that can handle dimming and blinking of white LEDs.
hello Andrew . you can get the ws2801 led strip by it . witop-led.en.alibaba.com/?spm=a2700.7756200.1998619056.11.PIO5ee or give me your email we will send you the data sheet. Contact jessie@witop-tech.com phone:0086+15676178187
HI,James. the led strips regular is 5M/roll. of course, other size can customised. learn more please link www.alibaba.com/product-detail/Addressable-32leds-ws2801-rgb-dc5v-led_60592190271.html?spm=a2747.manage.list.7.KkpEKq or send me your email, will send you details. jessie Email:jessie@witop-tech.com Phone:0086+15676178187
This setup we got from a 3rd party for the video demonstration. I believe we paid $150. Couldn't tell you who we got it from. This video was purely instructional, we do not plan to sell these yet. :) If we do, we will develop our own.
You can click here know more about this controller and WS2801 strips : www.ledstripsales.com/Full-color-controllers-c-56/t1000s-with-sd-card-pixel-controller-for-ws2801-ws2811-ws2812b-dream-color-magic-led-strips-p-2090.html www.ledstripsales.com/color-change-LED-Strip-c-38/ws2801-ic-5v-rgb-magic-color-programmable-series-flexible-led-strip-lights-160-leds-5mreel-p-2068.html
Hey FlexFire! Thanks for this great series of tutorials. I have the IC6803 LED Strips, Controller T-1000S and have this similar layout, I tried using lededit 2013, "Move Right" video effect... but my lights feel like they're alternating instead of all moving right... Did you ever encounter this issue? I can only guess the pixels are counted wrong but haven't figured out exactly what. Any advice?
Hello Iron Tank, sorry for the delay in response! One of our guys made this video as a helpful tool to answer some questions for some customers. He has left Flexfire on great terms to explore another opportunity. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
Does anyone know how to use the T8000 controller and the software setup on led edit 2014. i use a T1000 that is easily programmed by led edit. but if i try to program the leds with a T8000 i get random output not like the pattern i selected ( passage) .. Thanks
I don't think there is a way to do "real time" with a T1000S because it can only run programs loaded on to the SD Card in a loop. To get real time info, you would probably be best using an arduino controller with wifi.
Hello, I apologize but we currently do not sell these items. This was a sample order from a foreign supplier. This video is only for installation guidance only.
Hello Arturo, sorry for the delay in response! One of our guys made this video as a helpful tool to answer some questions for some customers. He has left Flexfire on great terms to explore another opportunity. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
Hi ,you can get more some here: www.alibaba.com/product-detail/Addressable-32leds-ws2801-rgb-dc5v-led_60592190271.html?spm=a2747.manage.list.7.ZDxCnY learn more please contact me:jessie@witop-tech.com phone:0086+15676178187
hello Fred. we are professional led manufacturer, if you need more different led lights, could you give me your email? we will send you the catalog. or course, learn more please link witop-led.en.alibaba.com/?spm=a2700.7756200.1998619056.11.PIO5ee Contact: jessie@witop-tech.com phone: 0086+15676178187
Hi, i'm having a trouble. I have a ws2812b strip with t1000s controller and the same power supply. After led 30-50 lights loss power, and almost every led after # 100 barely power on... I've tried wiring gnd to the end of the strip (as you mentioned), but I can only gain a bit of brightness, but still working wrong. What can I do? Thanks a lot.
the Ws2801 ic led strip is the SPI signal, if want to connect the VIa DMX. should add a decorder. if you have the DMX controller. you can just get the DMX led strip . can work with the DMX controller directly. learn more please Email: jessie@witop-tech.com phone/what's app: 0086+15676178187
![[ENGSUB] UNPRODUCTIVE DAY ใช้ชีวิต (เปื่อยๆ) ด้วยกัน 1 วัน! | OUROAD CLOSEFRiEND SS2 EP.9](http://i.ytimg.com/vi/pyYKZ3kra9w/mqdefault.jpg)
![⭐ฮิตในTikTok!! ( หมูเด้ง MooDeng ) Ver. แดนซ์โจ๊ะๆ ReMix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/3krsyfWUeHU/mqdefault.jpg)
![MV วิถีชีวิตใต้ - ผา อัยย๊ะ [Official MV HD]](http://i.ytimg.com/vi/nODlkOUu9B0/mqdefault.jpg)
0:22 I can't unsee this as you kissing the power supply.
I loved how the sd card says “256 MB” proudly
Oh, how technology has evolved. haha
Thank you for making these videos, I am just starting to learn about RGB pixels and their support products and your videos are the best I have found on the subject and thanks to you I hope to have a few RGB mini trees in my front yard next Christmas. Thank you again
Looks awesome! I only found this video because I was looking for flat panel LED lights for my bedroom. This setup would make it look like a disco!
thank God for you i was watching other videos that had no instructions just music and as a novice that did nothing for me
When connecting power between terminals, for safety and consistency, BLACK WIRE is normally used for GROUND (or V-) and RED or WHITE (less common) for Supply Voltage (V+, or VCC)
I have a question?, I have a LED strip ws 2812 B 100 meters, a strip of two meters is attached to the wall, total 50 strips are attached, total LED is 6000, which controller will be used for this? That works with audio?
Good work
I wanted to as: regard the strips, i saw that it's been looped (two strips looped as one line) how is the other end looped?
Detailed. Good demonstration.
Hi, good video.
Can you please tell me the nos of LED ?
And controller size.
Hi so i my power supply is only positive so i only have Com Com +V +V. can i somehow still use this or do i have to buy a new one?
Interesting. Do you have a link to the product you purchased? I would love to see it so we can help.
if I use a RGB LED matrix panel. you can use that controller or that you recommend? I want to transmit video
I see there is a voltage drop to the end of the strip, but how does adding a ground wire help?
Isn't it that the 5V wire should also be connected on another place?
Yes, as well, and not just at the end of the strip. Power loss will always occur, it's just a matter of reducing it as much as possible. Of you connect extra wires for ground and +5v at the end of the strip, the highest power loss will be in the middle then. Question is if you are able to notice it or not....
Sir sometime I see the led strip with no cover. Is that cover made by sillicon? And are you get it build in your led, or dissapear?
how many meters of tape can support the controller , it is probably important as power , greeting
Any way to wirelessly change the T1000s settings (speed, mode) or configure using LED Edit wirelessly? Or know of another controller that can do that?
I know nothing about any of this but I'd love to make one. So if I wanted to make a 10ft sign... would this be enough power. I would hook everything up the same? Thanks.
this is very nice piece of info thx
You are welcome!
In your vid: The GROUND wire (green), which they should call the common wire (?), is connected to the aluminum chassis? And the blue wire is VSS, which they should call GROUND? And VCC is the black wire? Thanks!
Where did you get the power supply, btw? I see a lot of them from China on eBay, but just wanted to know if I could order in the US.
thanks for breaking it down great video
Man thank you!! I love your work.
Awesome video will help immensely once my T1000S arrives. Quick question do i need to have a dimmable power supply for the T1000 and my Strips both 12v
not necessary to use dimmable , just DC12V power supply works. more help visit www.led-color.com
Is it possible to duplicate the led run on 2 panels?? I'm hoping to make a double sided box and I want the same on both sides
I'm looking to do this program on a DC system with 6v batteries and the ability to have 6v and 12v possible system. What are the key differences in the power supply I need to know?
toi muon lam 1 cai nhu the ,dai 3m rong 80cm ,gia khoang bao nhieu vay ?
I saw a 256M SD card, thats classic !
We do not carry these strips yet, this video is for information only. Flexfire LEDs sells ultra premium LED strip lights.(Some of the brightest in the world!) Please visit our site.
Do you guys sell something comparable to the programmable lights here... I only ask because I am working on a project to build an LED display panel for a theater for their marque
Ben Schran Shoot us an email at info@flexfireleds.com and explain a little bit about your project. We would love to help and offer any suggestions or product we believe will make your project a success!
*****
can we light up a deadmau5 helmet with this ? if so , will it be too hard for a beginner to make?
+Flexfire LEDs take the video down then
+Flexfire LEDs What type of SMD capacitors are on this strip? Please help I can't find out what they are anywhere!
Does the pixel number on the Auto layout means "sections" or number of LED on the strip?
I have a 5050 SMD300 strip, that on each "section" has 3 LEDs (each one is RGB).
I mean, if I want 30*30 layout, do I need 30 sections or total of 30 LEDs on the strip?
Great videos, thank you! Hey, can you share any insight on clear LED screens? (typically seen on large applications so the resolution being very coarse aids in the perception that it's clear) How are they doing that, are they somehow placing the chips to the side of the screen vs. inboard next to the LED, as seen on your example strips? Wondering if you might know of a good source to find clear strips and/or screen? Thanks again.
Hi, i am trying to install the program and i'm folowing your video, i do exactly the same as you but the program open a window with an error and it don't let me to continue. Do you know what could it be? When i put new file the error appears. I've downloaded around 50 different types of the led edit and in all of them i have the same problem, if you can help me it will be amazing. Thank you
Hi can you please show me how to connect the strip one to the other and connecting to the remote. I am planning to fix LED strip on my stair if you upload detailed video it will help me a lot .thank you
Do you know if 5v 2A would be enough to power about 95-100 of these leds? (That is about 3-4ish meters).
Hi, first thank's for that video. I bought the Controller and 10M of the W2801. Now i have a problem with the power supply. Is 60Amp not a bit to much? Can someone tell me if 20Amp is also enough?
Thanks! :)
Is there another led?
Thanks. 1st good video led on setup.
U helped a lot man, God bless u!! cheers
Hi Ryan
Thanks for 4 awesome and easy to understand tutorials.
I am wanting to make a project very like yours but with two differences.
First:
I want the LED display to be fully mobile.
(It's going to be a LED Flag, mounted on a carrying pole)
Is there a way of running it all of a 12Volt battery ??
I can find 12 volt LED RGB strips online. But don't know if they are compatible with the T1000S and I would like to know if the T1000S will run on 12V only, with out a 5 V input ?
Secound:
I'm on a Mac computer.
Do you know if there is a way to run "LED Edit 2013" on Mac OS X ?
Or if there is a similar program for Mac ??
Thanks
Peter
Sir, as you mentioned ws2801 ic used in these led strip and are they 5050 waterproof led strip ip67 and can be used it on outdoor..
Hello, I liked your video and would like to do the same but I am wondering how many strips of lights you use of how many LED counts and did you plug all of them together (chained) to just one output on the controller? Thanks in advance
nice! Can you trigger the scenes of this controller with DMX?
i prefer adding GND and 5V wires every meter, that way you get pretty good results
I have a T-4000 led controller. What is the file or software should I use to program? Thanks.
Good
Man, what kain of strip of led did you use in your video? Because i bought this ones: RGB 5050 SMD programmable WS2811 light strip and i hava this question...
2811 three wires,, 2801 four wires,
beebe.yang skype
Wendz from Phil here,plss where can I get or download the LEDedit 2013 v1.53 can I use another version for this? plss answer Thank you!
Is it possible to make something like this with a portable power source?
as big as a car battery might work, but should be 5v, output
beebe.yang, skype
Please tell me how much I can connect to such a controller such RGB ws8212 ???
would you need the power supply to make a real small one
Can someone explain or give a link to something informative about why the wire connection is like this? He connects V+ to 5V and V- to GND. I don't understand at all why... I've always learned about DC having V- V+ and GND, but this setup doesn't make sense to me... (semi-newbie in LED lighting here)
Considering the voltage drop: why do you add a red wire from the GND of the controller to the GND of the end of the strip? I thought you would have added an extra black wire running from your Power Supply (an extra V+ port) directly to the end of your strip (on the 5V dot, not the GND).
so the led can't be connect directly to pc or laptop to control the signs??
I suggest you a on-line controller.
where can we buy all the merch show in this vid?
I have ws2811 led strip lights and hc008 controller. I have connected 25 meters of strip lights. after 10 m the voltage drops and my lights don't emit all colours after 10 m. same like yours my strip lights also have arrow marks so that I don't power up the wrong side. however u connected the gnd wire to end of led strip going against the arrow direction. will this help me as well if I do the same
Shadab Khan: Did you find a solution? I have a similar question because I don't think he should be able to jump power by using the ground wire like he does in the video. From what I've learned, you should jump power using the 5v wire (makes more sense to use the power wire to jump power) and that is how I've done it in the few projects I've done. [From Power, I attach 5v to controller and to light strip; From Power, I attach Ground to controller and to light strip; From Controller, I attach ground to light strip].
I'm wondering if his ground and power might be switched and he doesn't realize, either because he mis-labeled or the Chinese controller has mislabeled its pins/ports? I've seen other T1000s with different labeling order than mine, so I wonder if some are mislabeled?
Any electricians out there who know why he was able to jump with his ground wire? Is the video correct?
Good . We are professional manufacturer of addressable pixel led / led strips . I'd like to add you to my professional network on LinkedIn & facebook .
The reason you add the ground to the end is to reduce the effective resistance of the bottom half of the LED's. The same thing is achieved by adding an additional power line. If you do both, you could vastly reduce power inefficiency due to accumulated resistance, however, adding a second ground to the end of the strips is usually enough. AFAIK, these stips use a common rail that runs down the back of all the strips, and the LED's and controllers tap into it in parallel. The arrows have NOTHING to do with flow of electricity, but flow of data.
Nice system we inspire at all.
I interesting to product.
can we in put video signal in your LED display???
what is the model number on your power supply I am trying to find one and I can't exactly find it
+microtruckerwg Hi there, thanks for watching our videos. We have upgraded our power supplies, Feel free to give us a call at 1-844-FLEXFIRE and we will be happy to assist you with the design of your project!
I bought 5 of these off eBay for $20.00 each with free shipping from Hong Kong, they are called "SUPERNIGHT 12V DC 30A 360W Regulated Switching Power Supply" and all 5 of them work fine, the only problem I am having is with the thermostats, I can't get the power supplies to run quietly.
Anyway, as soon as I wire up and plug the units into an outlet (without even drawing a single watt of power) all of the fans turn on at full-speed?! I was told the fans are only supposed to come on when the units start getting heated, or begin reaching their maximum 360 watt loads, but now from COLD-START/ZERO LOAD?!? Why are the fans running at max speed ALL THE TIME? Constant fans running at full-speed makes these units super, super noisy!
Do you know if this 'fans-always-on' issue can be fixed? I am running our office LED lighting system from these which are nowhere near the full 360 watt load (more like 120 watts) but the fans running at full force with even just 1 watt, makes every one of these power supplies unusable. :(
Totel set amount
i have all the things on the video but my led strip is 12v-DIN-GND i have only 3 outputs and 2 wires goes out from "12v" and 1 wire goes out from "DIN" and 2 wires goes out from GND hmm
Can you explain what is the difference between the 3 wire (I believe Digital) to the 4 wire strips? & can you explain the differences in the WS28- models?
Thanks Murf!
Hello Dan, sorry for the delay in response! One of our guys made this video as a helpful tool to answer some questions for some customers. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
LED strip dislay is one trend of LED display, it's much lighter than traditional LED dislay , low wind load and you don't need air-condition for it's not enclosed design.
We worked with it for years , and we've developed some Series of the product . Pls come visit our website if you are interesting and let's together develop the technology .
Could you use this type of setup to control warm white leds?
Yes, but it is likely overkill for whites unless you have a project requiring each led to be programmable at different intensities (this set-up controls millions of colors and each led individually). There are much simpler controller/power set-ups that can handle dimming and blinking of white LEDs.
Thank you!
i have those lights but kinda different where do you get them and how much
hello Andrew . you can get the ws2801 led strip by it .
witop-led.en.alibaba.com/?spm=a2700.7756200.1998619056.11.PIO5ee
or give me your email we will send you the data sheet.
Contact
jessie@witop-tech.com
phone:0086+15676178187
is my dream for doing think like that but i nee toll for do this but no link where buy stuff ?
What is the average length of strips used in this setup? Not really sure how much I would need to buy.
beebe.yang, skype,
for a 32LEDs pr meter, 10w per meter, better to add extending power cables each 2.5 meters
HI,James. the led strips regular is 5M/roll. of course, other size can customised. learn more please link www.alibaba.com/product-detail/Addressable-32leds-ws2801-rgb-dc5v-led_60592190271.html?spm=a2747.manage.list.7.KkpEKq
or send me your email, will send you details.
jessie
Email:jessie@witop-tech.com
Phone:0086+15676178187
Jessie Feng I am looking for a waterproof setup for my car. that I can do something like this. can you help me
Nice project, can you name the type of controller you are using and is it possible to program Russian text (Cyrillic)? Any help is appreciated.
It's the T1000s, u can buy it.on ebay for less then 20 us dollars
is it possible to use a regular led 5050 strips to do this
No, unfortunately, they cannot be independently controlled. You would need these WS2801 strip lights.
I would like to know how much is the set up like that one that you show on the video?
This setup we got from a 3rd party for the video demonstration. I believe we paid $150. Couldn't tell you who we got it from. This video was purely instructional, we do not plan to sell these yet. :) If we do, we will develop our own.
thank you man... seriously
I want to buy this T1000S controller, SD Card , and WS20801 IC strip lights . where I Can buy in Cambodia ?
You can click here know more about this controller and WS2801 strips : www.ledstripsales.com/Full-color-controllers-c-56/t1000s-with-sd-card-pixel-controller-for-ws2801-ws2811-ws2812b-dream-color-magic-led-strips-p-2090.html www.ledstripsales.com/color-change-LED-Strip-c-38/ws2801-ic-5v-rgb-magic-color-programmable-series-flexible-led-strip-lights-160-leds-5mreel-p-2068.html
Does anyone know is anywhere schematics of T-1000s controller?
Hey FlexFire! Thanks for this great series of tutorials. I have the IC6803 LED Strips, Controller T-1000S and have this similar layout, I tried using lededit 2013, "Move Right" video effect... but my lights feel like they're alternating instead of all moving right... Did you ever encounter this issue? I can only guess the pixels are counted wrong but haven't figured out exactly what. Any advice?
Hello Iron Tank, sorry for the delay in response!
One of our guys made this video as a helpful tool to answer some questions for some customers. He has left Flexfire on great terms to explore another opportunity. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
Can you show me a picture? Maybe i can help you find out the problem.
does this controller capable of running video? or to be connected to pc?
This controller probably not.
Also, running video (on 60FPS) is a pretty harsh timing constraint.
What clock pin is used for ?
Does anyone know how to use the T8000 controller and the software setup on led edit 2014. i use a T1000 that is easily programmed by led edit. but if i try to program the leds with a T8000 i get random output not like the pattern i selected ( passage) .. Thanks
Hello I need some sugestion,how I can have real time clock and temp on same display like this.I using T1000s controller.thanks
I don't think there is a way to do "real time" with a T1000S because it can only run programs loaded on to the SD Card in a loop. To get real time info, you would probably be best using an arduino controller with wifi.
Thank you so much for telling how this works.
Hello! how many leds can use direct connected in sequence in T1000 controller?
MAX 2048 leds connect to T1000 controller. To get more LEDs be controlled, i suggest T8000, it can control MAX 8192 leds.
so nice
Hi I will like all the part for this. Where can i place my order?
Hello, I apologize but we currently do not sell these items. This was a sample order from a foreign supplier. This video is only for installation guidance only.
thanks, brother.
hi, does the controller also work with strips whitout clock?
ws2801 is double signal 。Date and clock . need install clock pin . ws2811 is 3 pin with out clock
controller works for both ws2801 and ws2811 led strip, more information see www.led-color.com/index.php/Product/view/id/705.html
would you please tell the name off the white box controller, and the specification , beucause i want buy one in mexico
Hello Arturo, sorry for the delay in response!
One of our guys made this video as a helpful tool to answer some questions for some customers. He has left Flexfire on great terms to explore another opportunity. We do not carry this product yet and our current knowledge on these products are limited. We are not able to offer too much extra info but I will do some research and message you when I get the right answer for you!
T-1000s
can you make a video of ws2801 led with music sync
Is there any way to do this without rgb leds?
I am sure some company out there sells the individually addressable single color LED chips. If we come across any, I will let you know!
Just to replace the RGB with single color LEDs, such as white only.
How did you connect the strips? 5v to gnd CO to DI?
He told it.
Data to DI
Clock to CI
5V to 5V
GND to GND
can u help us where selling point of WS2801 LEDs
+Royal Arts ru.aliexpress.com/item/100-PCS-LOT-WS2801-WS2801SO-IC-SMD-FREE-SHIPPING/1589268385.html
Does anyone know if there is a way to control this with an HDMI instead of an sd card?
i like to get information and cost of all de material de i need to make something like that. tanx
Hi ,you can get more some here: www.alibaba.com/product-detail/Addressable-32leds-ws2801-rgb-dc5v-led_60592190271.html?spm=a2747.manage.list.7.ZDxCnY learn more please contact me:jessie@witop-tech.com
phone:0086+15676178187
do you sell the SD cards already with different light modes? pretty much like plug and play
hello Fred. we are professional led manufacturer, if you need more different led lights, could you give me your email? we will send you the catalog. or course, learn more please link witop-led.en.alibaba.com/?spm=a2700.7756200.1998619056.11.PIO5ee
Contact: jessie@witop-tech.com
phone: 0086+15676178187
Dirtyderfdog@gmail.com. I was wondering if you have any that have many different lighting modes.
Fred Arce ok. thanks a lot, Fred. i will send you the link to know our products.
please remember check email. thanks a lot!
info here please djsonidosuper@yahoo.com tanx
You should go to inplix webpage if you want to learn how to build it yourself.
Nice
Hi, i'm having a trouble. I have a ws2812b strip with t1000s controller and the same power supply. After led 30-50 lights loss power, and almost every led after # 100 barely power on... I've tried wiring gnd to the end of the strip (as you mentioned), but I can only gain a bit of brightness, but still working wrong. What can I do? Thanks a lot.
I think some LED is broken, it cased the Signal transmission failure.
Can you connect via DMX?
the Ws2801 ic led strip is the SPI signal, if want to connect the VIa DMX. should add a decorder. if you have the DMX controller. you can just get the DMX led strip . can work with the DMX controller directly.
learn more please Email: jessie@witop-tech.com
phone/what's app: 0086+15676178187
What were the gauge of the wires you used?
Buy this controller and strips free with 2.5 square connector cable.
SuperLightingLED you can click here know more about this controller: www.ledstripsales.com/Full-color-controllers-c-56/
what is your software ?
ws2811 and ws2812 work?
Coud you please tell me how connect the strips ,looks like they are in parallel but i see cables at both ends, anyone knows?
never mind,the strips are connected in series
good luck brother
Price led & controler
where can i find all the power supply and also the software for the led,, i want to put words,,,
Hello. We Are Led manufacturer, we have The Supply power, give me more details, or contact jessie@witop-tech.com
Phone/what's app:0086+15676178187