Dołączam się do podziękowań za kolejny świetny tutorial. Lampki zamówiłem z podanego linka - wiązki super, nie trzeba było przedłużać a nawet te bez oplotu skracałem. Przewody dość grube, miedziane, końcówki pasowały jak trzeba. Natomiast lampki: te na przedzie były na wymiar zaś z tyłu nie wchodziły i trzeba było trochę powiększyć otwór na długość (jakieś 2 mm). Kodowanie, tu też był problem ponieważ linijki od 10 do 24 - nie udało mi się znaleźć takich pozycji (jak czytam komentarzach, inni też mieli z tym problemy). Mimo wszystko oświetlenie działa i w ustawieniach w radiu mogę regulować jasność oświetlenia. Tak więc super, jestem zadowolony z tej modyfikacji. Jeszcze raz wielkie dzięki.
Thank you very much for your video and help. Every thing was good except when coding with OBDEleven on: Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14, it doesnt accept value 14 it gives some kind of error so used 1 and every thing is working fine and also Adaptation → Ambient lighting - Defaultwert Ambienteprofil Fussraum → 100% i couldnt find it so i just left it and i works fine (i have golf 7). Thank you again for your instructions and time to help other peopel! BIG thumb up
I just retrofited in my golf 7.5. Thanks for this video. I see more clearly the pass of the wire. In my case the coding is more than others put in his mk7. In 7.5 is integrated in the ambient lights
Thanks for the video and the coding details provided., i had been scratching my head for almost 2 yrs now to get this working. The missing piece was the interior lighting parameters. Finally got this to work. Only issue was those adaptation changes did not work on my VCDS. But had to use the VCP Tool for the coding.
Hi, I probably have the same problem - my VCDS does not want to find (display) when encoding channels "interior lighting: parameter - p_adation and interior lighting: parameter - p_helligkeit". Can I ask for advice on how to solve this?
When are you planning to do part 2? I love your tutorials, very well explained but I don't want to attempt this install until you've shown the full guide for front and back! Hope you will do it soon
No i pięknie :) Na filmiku tylko nie ma pokazane jak zdejmujesz klamkę od maski :) a o tym trzeba pamiętać. Czekam teraz na część 2 po stronie pasażera i przydała by się część 3 fotele z tyłu :D Good Job !
Very illustrative video, the only flaw is the fact that from how you can see in the video the lights you have mounted do not illuminate the footwell much for the rest Ok
@@mrfixplhello I was using your video to install these AliExpress foot well lights on my 18 Passat GT, the problem I’m having is the GT has 52 pin bcm plug I’m not sure where to plug in the light pin can you help??
Is there enought cable for passenger rear light, to be mounted under the door plastic trim? Im thinking about doing the exact same procedure as you have done but that is my only concern. Im thinking that if it's not enough cable then i might have to route it under the "gearbox" plastic trim. I have seen on AliExpress that they sell same cables as you have and that the length should be 180 cm. Thanks for helping👍
Hi mr-fix, congratulations for the tutorial, I have a question, what is the purpose of enabling bits 7 and 3? Coding → Long Coding → Byte: 05 → Bit: 7 → enable Coding → Long Coding → Byte: 17 → Bit: 3 → enable
One of them enables footwell lights in general. The other one enables ambient background illumination in footwell. Some newer MK7s does not require coding at all, just adaptation changes. Coding is filled with 00. VW at some point switched to adaptations in BCM module.
Ciao. Complimenti per il video sei bravissimo , Oltre che alla c3ntralina nel pin , potrei collegare il cavo positivo con un ruba corrente ai fusibili luce plafoniera abitacolo ? Onde evitare attivazioni vag ? Grazie mille
I believe I did removed it. It fairly simple, but was not visible on video and I edited it out. Sorry for the confusion. You can check my video about installing aluminum pedals. i believe it's shown when installing the dead pedal.
Hi and tnx for the video. I just finished install on front and rear footwell lights. Codinig was slightly different on my MK 7.5 comfortline: 1.No Ambient lighting in Adoptions on my car. (Adaptation → Ambient lighting - Defaultwert Ambienteprofil Fussraum → 100% ) 2.Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14 - it would not accept value 14 or multiple other values that i tried randomly :) It accepted value 1. Everything works as it should. Brightness level is adjustable from infotainment unit. My kit is from CarSystems.eu - www.carsystems.eu/golf-7-5-lighting-parts-accessories,tag.html
Hi mr-fix i'v learned a lot from your videos thanks..I have install the wires for the first light under the dash to the 72 pin connector and the braun wire to the chassi just like in your video. I also code this with OBDeleven but nothing happens the light will not go one? Can you tell me why i have this problem?
Hi, there is any coding that is possible turn on courtesy lights and footwell lights with doors closed? (When turn on all courtesy lights). Many thanks
Hello mr.fix, I’m trying to find the same product you have shown in the video but only for the front two seats, I don’t feel confident in doing the rears also, will I be able to use the 4 piece set given and just miss the two rear lights or will I need to get a set that has just the front two, I can’t seem to find the right one with correct wiring, is there anyway you can help me?
Hi! Thanks for the video, I made a foot light on my car. the problem is that block 9 does not support encoding, only through adaptations. I made adaptations as described by you, but the light is not on. Can you tell me how to do it?
@mr-fix . Do you know how many leds each light have ? mine set has 1 smd led each light , something doesnt look right . I already coded and im waitting to see at night
BCM has 3 conenctors with 70+ pins on each. Only 35 (or so) of them are used to control lights and are programmable. And C72 is the pin used originally by VW when the car is equipped with footwell lights.
hey man, I'm thinking to do this to my car, but I dont I have the obdeleven to do the coding part but I'm going to buy one. there are 3 version of obdeleven the ultimate generation. Can I use the coding part with the obdeleven starter pack?
Hello. I did everything as described by you(all the coding steps) but, in the multimedia system(mib 1 Discover Media 5G0 035 846 i do not hav the "Footwell light" option slider on the light menu. Is there something else to do? Many thanks.
Ciao, prima di tutto complimenti per i magnifici video che fai, ti scrivo perchè ho seguito le tue indicazioni alla lettera per il montaggio luci vano piedi nella mia golf7, è andato tutto bene tranne che quando provo ad inserire il valore 14 ( Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14 ), mi viene fuori valore errato, potresti aiutarmi, grazie ancora e spero di ricevere tue notizie, ciao.
hello, listen but the coding that you put where it starts, adaptation, interior lighting, parameters .... I do not find them, among all the items from the drop-down menu, searched and searched, nothing. I do it with VCDS 20.4 .. can you help me? because on the on-board cb I was able to put the controls + and - for the intensity! but they don't act! thanks
hi just retrofitted the footwell light on my golf 7.5 but i have a problem the light is very low even when i put the maximum brightness on the infotainment , when i change the brightness on LC72 AB dimwert from 100 to 127 the brightness is high but i can't dim it from the infotainment anymore , any have the solution to this?
If dimmwert is set above 100 it will fallback to default setting with max brightness, no fade effect and no controls. Set it to 100 and check the Adaptation → Channel: Interior lighting; parameter channels which are set to 70%
@@mrfixpl yes exactly i tried this just to make sur the footwell work well, because even when it's night we see it just a little bit even when i dim it on maximum Thanks i will check this adaptation
Hello, I installed all the lighting for the legs, everything as in the video, only I installed other led lights from skoda. I made the adaptation, the lighting of the legs appeared in the menu, but the lights do not light up. Could it be due to non-original LED lights? car VW golf 7.5 2019
I've been coding for the footwell lights option on the infotainment but there's no reaction for the lightning intensity and off. Anyone have solved?? 🤔
Hello Mr-Fix, I installed my lights and I am coding with OBDeleven. I have a 2019 sportwagen S. I need help with a couple coding issues I have. I can not change the long coding. When trying to execute changes I get messaged “function not available” Adaptation > Ambient Light - says “There are not items available for this option” p_adaption_kundenwunsch_fussraum>14 - says “Function cannot be performed, mess. length or formate incorrect” All other adaptations have been excepted by the vehicle. Currently the footwell lights only turn on when the door is open. Thank you for your help.
Dragans comment on this video fixed my coding issue by just inputting 1 instead of 14 under adaptation_kundenwunsch_fussraum. Footwell lights working as supposed to😊
Getting issues with the obdeleven coding. I get the error: "(13) Function cannot be performed, mess. length or format incorrect" When messing with: "Adaptation → Interior lighting; parameter" Half the coding is done here which is a problem. I also don't even have this menu in 5F- "Adaptation → Car_Function_Adaptations_Gen2" Everything is installed. I have 2door hatch and just used all four lights up front instead of putting the two in the seat of the car for the back row.
I installed all 4 lights in my golf 7 2015 lounge, but after several attempts I had to code them to adjust them together with the ambient lights. Now I have seen your video and tried to replicate your own coding, with no success. I receive an error message (Incorrect message length or invalid format) when I try to change one of these parameters Adaptation → Interior lighting; parameter - p_[...], They are all at 0. Do you have an idea how it could be solved? Thanks
Please make sure that you have entered the security access code first. And there might be a timeout from when you enter the security access to the first parameter change, so if you don't make any change within on minute or so, the access code expires.
@@mrfixpl thanks for the reply, unfortunately it is not a problem of timeout or security code, but specific of this category of parameters (Interior lighting; parameter - ...) that in my case cannot be changed, no problem with others
Same issue here for me., none of the parameters for interior lighting works for me with VCDS. get an error something like CAN Messages greater than 256 bits not supported. Wondering if other tools like VCP or VAS5054 can code this adaptations. Since all of this values as set to 0% ., footwell lights will not turn on.
Hi mr-fix, I have a problem with follow code: p_adaption_kundenwunsch_fussraum -> 14 (Default 0.00) The value 14 is not accepted from system. The same value in bin 1110, is not accepted from system. Only value accepted from system is 0.14 Wicth value you have put? Anyway, I made all the adaptations and for code, p_adaption_kundenwunsch_fussraum I have used 0.14, but the menu "Footwell Lighting" on the infotainment display, is not visible. The Footwell Light are not connected yet, could be the cause? Thanks best regards
I answer myself, the correct code is, p_adaption_kundenwunsch_fussraum -> 0.2 In my Golf 7.5 the new menù is in "Ambient Light" and allows for HMI dimming adjustment
hi, I started coding the procedure as you wrote in detail ... I managed with Vcds to codify only the first part, the long coding, terminal 72 enabling, and the coding for the display control module! ... part concerning the adjustment of the lights ... nn I was able to find the various wordings in the drop-down list .. it is very complicated and long. how can i solve? thank you
in my golf mk 7.5 i can't activate ambient lighting-defaultwert ambientprofil fussraum-100%. does not open ambient lighting says that the system does not respond why? can you help me I can't get them to light up
Hello, I come to ask you because Isearched everywhere and watched a lot of tutorials but I didn’t find what I was looking for Here is my problem : I have a Golf 7.5 with basic rear led lights (forums.vwvortex.com/showthread.php?8571473-North-America-gets-screwed-again-here-are-the-LED-lights-for-NA) I bought original MK7.5 dynamic rear lights, sold with wires (four wires). For now I plugged all normally without new adding wires, just cuted a little the plug connectors for them to make them compatible. What works ? - « general » light works - Exterior left and right trurn lights work (no dynamic) Problems/missing : - No exterior left and right rear turn lights - No back drive lilghts (onboard lights ON when problem detected : driving back) What say the install book : - Climping out all needed plastic - installing and connecting the « 4 wire harnet » between rear left and right lights and going to BCM - Code with ODIS My questions : - Am I obliged to code with ODIS, it’s a professionnalsofware… - If obliged to, where must I go to ask for this ? only offical garage VW ? - If I do all the work but not yet coding, what happen ? only lights onboard ? - Where can I find tutorials about clipping out wire bottom doors ? (rear door panel it’s ok) Sorry, it’s long, but I’m in the mess:/ please help me PS : If you have some information about putting off then on an airbag seats of Golf 7.5… I take… Mathieu
Need OBDeleven?
🎟 Get 10% OFF with code: MRFIX10
🛒 mr-fix.info/redirect/obdeleven
Dołączam się do podziękowań za kolejny świetny tutorial. Lampki zamówiłem z podanego linka - wiązki super, nie trzeba było przedłużać a nawet te bez oplotu skracałem. Przewody dość grube, miedziane, końcówki pasowały jak trzeba. Natomiast lampki: te na przedzie były na wymiar zaś z tyłu nie wchodziły i trzeba było trochę powiększyć otwór na długość (jakieś 2 mm). Kodowanie, tu też był problem ponieważ linijki od 10 do 24 - nie udało mi się znaleźć takich pozycji (jak czytam komentarzach, inni też mieli z tym problemy). Mimo wszystko oświetlenie działa i w ustawieniach w radiu mogę regulować jasność oświetlenia. Tak więc super, jestem zadowolony z tej modyfikacji. Jeszcze raz wielkie dzięki.
Thank you so much for sharing, I just installed the lights in a Sportsvan with ease! Only problem were the missing holes under the front seats. 👍⚡💡
Thank you very much for your video and help. Every thing was good except when coding with OBDEleven on: Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14, it doesnt accept value 14 it gives some kind of error so used 1 and every thing is working fine and also Adaptation → Ambient lighting - Defaultwert Ambienteprofil Fussraum → 100% i couldnt find it so i just left it and i works fine (i have golf 7). Thank you again for your instructions and time to help other peopel! BIG thumb up
I'm also having this problem right now. Can you give a update on if you fixed it or still have this problem?
I just retrofited in my golf 7.5. Thanks for this video. I see more clearly the pass of the wire. In my case the coding is more than others put in his mk7. In 7.5 is integrated in the ambient lights
Friend, my golf is the mk7.5 comfortline. How can you pass all the complete coding? Thanks.
in my 2019 Touran i think i need the mk 7,5 coding, cause mk7 one doesn’t work. Can you share it please…?
@@eliranferreira599 hi did you find coding for golf 7.5
Hi. Where i find coding for mk7.5?
Thanks for the video and the coding details provided., i had been scratching my head for almost 2 yrs now to get this working. The missing piece was the interior lighting parameters. Finally got this to work. Only issue was those adaptation changes did not work on my VCDS. But had to use the VCP Tool for the coding.
Hi, I probably have the same problem - my VCDS does not want to find (display) when encoding channels "interior lighting: parameter - p_adation and interior lighting: parameter - p_helligkeit". Can I ask for advice on how to solve this?
When are you planning to do part 2? I love your tutorials, very well explained but I don't want to attempt this install until you've shown the full guide for front and back! Hope you will do it soon
No i pięknie :) Na filmiku tylko nie ma pokazane jak zdejmujesz klamkę od maski :) a o tym trzeba pamiętać. Czekam teraz na część 2 po stronie pasażera i przydała by się część 3 fotele z tyłu :D Good Job !
th-cam.com/video/O77wrH7GyfA/w-d-xo.html
Waiting for the interesting part 2
Thank you for the video 👍🏾
✌️
Very illustrative video, the only flaw is the fact that from how you can see in the video the lights you have mounted do not illuminate the footwell much for the rest Ok
Great video, quick question, can I follow this method for a 2018 VW Passat GT???
I believe yes
@@mrfixpl thank you I can’t wait to try!!
@@mrfixplhello I was using your video to install these AliExpress foot well lights on my 18 Passat GT, the problem I’m having is the GT has 52 pin bcm plug I’m not sure where to plug in the light pin can you help??
Is there enought cable for passenger rear light, to be mounted under the door plastic trim? Im thinking about doing the exact same procedure as you have done but that is my only concern. Im thinking that if it's not enough cable then i might have to route it under the "gearbox" plastic trim. I have seen on AliExpress that they sell same cables as you have and that the length should be 180 cm. Thanks for helping👍
Hello, thanks for the help of your video. in the case of golf mk7.5 of 2017 is it the same coding? or change
Hi mr-fix,
congratulations for the tutorial, I have a question,
what is the purpose of enabling bits 7 and 3?
Coding → Long Coding → Byte: 05 → Bit: 7 → enable
Coding → Long Coding → Byte: 17 → Bit: 3 → enable
One of them enables footwell lights in general. The other one enables ambient background illumination in footwell.
Some newer MK7s does not require coding at all, just adaptation changes. Coding is filled with 00. VW at some point switched to adaptations in BCM module.
@@mrfixpl Hi mr-fix,
is it correct that the following parameters are different?
- p_helligkeit_HD_auf_zuendung_ein_fussraum -> 126%
- p_helligkeit_HD_auf_zuendung_aus_fussraum -> 127% -> 126% ?
- p_helligkeit_Fzg_geschlossen_zuendung_ein_fussraum -> 126% -> 70% ?
- p_helligkeit_Fzg_geschlossen_zuendung_aus_fussraum -> 70%
Hi mr-fix, what code did you use?
- p_helligkeit_HD_auf_zuendung_ein_fussraum -> 126%
- p_helligkeit_HD_auf_zuendung_aus_fussraum -> 127% -> 126% ?
- p_helligkeit_Fzg_geschlossen_zuendung_ein_fussraum -> 126% -> 70% ?
- p_helligkeit_Fzg_geschlossen_zuendung_aus_fussraum -> 70%
Hi, can you please post the link where you bought 12v to 5v dc converter and that 2 usb sockets in the back? Thank you
Waiting for Part two..!!
It's taking long, isn't it? Hope to move it forward this or next week.
mr-fix it would be great to see the part 2 fella, I’m wanting to do the same sort of thing and this is helping a lot
Ciao. Complimenti per il video sei bravissimo , Oltre che alla c3ntralina nel pin , potrei collegare il cavo positivo con un ruba corrente ai fusibili luce plafoniera abitacolo ? Onde evitare attivazioni vag ? Grazie mille
Hi, how you remove the footwell plastic without remove hood latch release handle bracket? Thanks
I believe I did removed it. It fairly simple, but was not visible on video and I edited it out. Sorry for the confusion.
You can check my video about installing aluminum pedals. i believe it's shown when installing the dead pedal.
Hi and tnx for the video. I just finished install on front and rear footwell lights. Codinig was slightly different on my MK 7.5 comfortline:
1.No Ambient lighting in Adoptions on my car. (Adaptation → Ambient lighting - Defaultwert Ambienteprofil Fussraum → 100%
)
2.Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14 - it would not accept value 14 or multiple other values that i tried randomly :) It accepted value 1.
Everything works as it should. Brightness level is adjustable from infotainment unit.
My kit is from CarSystems.eu - www.carsystems.eu/golf-7-5-lighting-parts-accessories,tag.html
Hello. The footwell lights appears in the light menu?
For me only appears in ambient light menu. I have a 7.5 facelift too
@@carlosb68 Friend, my golf is the mk7.5 comfortline. How can you pass all the complete coding? Thanks.
Thank you, Inputting 1 fixed my issue with coding the lights to the car!
Hi mr-fix i'v learned a lot from your videos thanks..I have install the wires for the first light under the dash to the 72 pin connector and the braun wire to the chassi just like in your video. I also code this with OBDeleven but nothing happens the light will not go one? Can you tell me why i have this problem?
Hi do you resolve your issue i have the same problem
Vsetko funguje jak ma kodovanie na 100% najlepsi navod .dakujem
Is the install the same for an seat Ibiza SC 2016, i know there are models with footwell lighting installed from the factory
Hi, there is any coding that is possible turn on courtesy lights and footwell lights with doors closed? (When turn on all courtesy lights). Many thanks
Hi I have a golf 7.5, I have performed the coding but the adjustment for the footwell light does not appear on the menu
Nice
Hello mr.fix, I’m trying to find the same product you have shown in the video but only for the front two seats, I don’t feel confident in doing the rears also, will I be able to use the 4 piece set given and just miss the two rear lights or will I need to get a set that has just the front two, I can’t seem to find the right one with correct wiring, is there anyway you can help me?
Hi! Thanks for the video, I made a foot light on my car. the problem is that block 9 does not support encoding, only through adaptations. I made adaptations as described by you, but the light is not on. Can you tell me how to do it?
Check my recent video about cupholder lights. Might help you a bit with troubleshooting this in your car.
hi, do you think it can be installed in the passat b7 as well?
Boa Noite
Aplica-se no polo brasileiro plataforma MQB?
@mr-fix . Do you know how many leds each light have ? mine set has 1 smd led each light , something doesnt look right . I already coded and im waitting to see at night
I believe that OEM is using just one SMD LED. But you can go with standard light (with a W5W bulb) and replace it with LED of your choice.
@@mrfixpl I bought the whole set with led lights (AliExpress), thanks for all the coding .
Does footwel light work in drive with this coding and if open door
sorry but the difference between the connection to pin 72 of connector C or to pin 50 of connector B., what changes? Thank
BCM has 3 conenctors with 70+ pins on each. Only 35 (or so) of them are used to control lights and are programmable.
And C72 is the pin used originally by VW when the car is equipped with footwell lights.
No Golf 72 footwell. No polo 19 72 Luz portas.
hey man, I'm thinking to do this to my car, but I dont I have the obdeleven to do the coding part but I'm going to buy one. there are 3 version of obdeleven the ultimate generation. Can I use the coding part with the obdeleven starter pack?
Get the PRO pack. And check my OBDeleven review to learn more.
Do the Set also fit for a touran II?
Wiring length might be different
Did you ever install footwell on 2q bcm
Friend, does this encoding fit the golf mk7.5 comfortline?
it should.
Can I fit these with a MIB1 head unit?
Hello. I did everything as described by you(all the coding steps) but, in the multimedia system(mib 1 Discover Media 5G0 035 846 i do not hav the "Footwell light" option slider on the light menu. Is there something else to do? Many thanks.
Ciao, prima di tutto complimenti per i magnifici video che fai, ti scrivo perchè ho seguito le tue indicazioni alla lettera per il montaggio luci vano piedi nella mia golf7, è andato tutto bene tranne che quando provo ad inserire il valore 14 ( Adaptation → Interior lighting; parameter - p_adaption_kundenwunsch_fussraum → 14 ), mi viene fuori valore errato, potresti aiutarmi, grazie ancora e spero di ricevere tue notizie, ciao.
hello, listen but the coding that you put where it starts, adaptation, interior lighting, parameters .... I do not find them, among all the items from the drop-down menu, searched and searched, nothing. I do it with VCDS 20.4 .. can you help me? because on the on-board cb I was able to put the controls + and - for the intensity! but they don't act! thanks
hi just retrofitted the footwell light on my golf 7.5 but i have a problem the light is very low even when i put the maximum brightness on the infotainment , when i change the brightness on LC72 AB dimwert from 100 to 127 the brightness is high but i can't dim it from the infotainment anymore , any have the solution to this?
If dimmwert is set above 100 it will fallback to default setting with max brightness, no fade effect and no controls. Set it to 100 and check the Adaptation → Channel: Interior lighting; parameter channels which are set to 70%
@@mrfixpl yes exactly i tried this just to make sur the footwell work well, because even when it's night we see it just a little bit even when i dim it on maximum
Thanks i will check this adaptation
@@mrfixpl th-cam.com/video/lvCuXAcGcAY/w-d-xo.html
here a video of the led footwell
is it the same for Audi A5 b8?
Can you do the coding with obd11 ?
Sure!
@@mrfixpl where can I buy the harness from as they don’t sell them anymore on aliexpress need one that I can code with obd11
@@mrfixpl am going to buy a set of kufatec footwell light off eBay just wondering can I still copy ur coding ?
İs this codding procedure same with vcds, do you know ?
Yes, the same. VCDS, OBDeleven and other diagnostic tools are just "terminals" that connect with the car to see what's available over there.
@@mrfixpl You are describe very well what diagnostic tools to do, thank you, ı will continue to follow you
Hallo - Wissen Sie warum mein Auto keine Option im Radio hat um die Lichter bei den Füßen zu schalten?
Are those lights installed in the car?
Hello, I installed all the lighting for the legs, everything as in the video, only I installed other led lights from skoda. I made the adaptation, the lighting of the legs appeared in the menu, but the lights do not light up. Could it be due to non-original LED lights? car VW golf 7.5 2019
I have the same issue, do you resolved the problem ?
Hello. I have built everything in the lamps work. the only thing I can't get is the brightness adjustment in my screen can someone help me?
Have you checked coding instruction in the description of this video?
Witam. Czy rozwiązałeś problem?
hi its works for a seat leon 5f 2017 1.2 tsi? thx you
Should be the same for Leon 5F and Octavia 5E.
What BCM is installed? Or rather, where can I find the bcm's squematic? I have leon 5f (MQB) 2017 and rapid spaceback (pq25 platform) 2015
I've been coding for the footwell lights option on the infotainment but there's no reaction for the lightning intensity and off. Anyone have solved?? 🤔
Hello Mr-Fix, I installed my lights and I am coding with OBDeleven. I have a 2019 sportwagen S. I need help with a couple coding issues I have.
I can not change the long coding. When trying to execute changes I get messaged “function not available”
Adaptation > Ambient Light - says “There are not items available for this option”
p_adaption_kundenwunsch_fussraum>14 - says “Function cannot be performed, mess. length or formate incorrect”
All other adaptations have been excepted by the vehicle. Currently the footwell lights only turn on when the door is open.
Thank you for your help.
Dragans comment on this video fixed my coding issue by just inputting 1 instead of 14 under adaptation_kundenwunsch_fussraum. Footwell lights working as supposed to😊
Getting issues with the obdeleven coding.
I get the error:
"(13) Function cannot be performed, mess. length or format incorrect"
When messing with:
"Adaptation → Interior lighting; parameter"
Half the coding is done here which is a problem.
I also don't even have this menu in 5F-
"Adaptation → Car_Function_Adaptations_Gen2"
Everything is installed. I have 2door hatch and just used all four lights up front instead of putting the two in the seat of the car for the back row.
I installed all 4 lights in my golf 7 2015 lounge, but after several attempts I had to code them to adjust them together with the ambient lights.
Now I have seen your video and tried to replicate your own coding, with no success.
I receive an error message (Incorrect message length or invalid format) when I try to change one of these parameters Adaptation → Interior lighting; parameter - p_[...],
They are all at 0. Do you have an idea how it could be solved?
Thanks
Please make sure that you have entered the security access code first. And there might be a timeout from when you enter the security access to the first parameter change, so if you don't make any change within on minute or so, the access code expires.
@@mrfixpl
thanks for the reply, unfortunately it is not a problem of timeout or security code, but specific of this category of parameters (Interior lighting; parameter - ...) that in my case cannot be changed, no problem with others
Same issue here for me., none of the parameters for interior lighting works for me with VCDS. get an error something like CAN Messages greater than 256 bits not supported. Wondering if other tools like VCP or VAS5054 can code this adaptations.
Since all of this values as set to 0% ., footwell lights will not turn on.
Hi mr-fix,
I have a problem with follow code:
p_adaption_kundenwunsch_fussraum -> 14 (Default 0.00)
The value 14 is not accepted from system.
The same value in bin 1110, is not accepted from system.
Only value accepted from system is 0.14
Wicth value you have put?
Anyway, I made all the adaptations
and for code, p_adaption_kundenwunsch_fussraum
I have used 0.14, but the menu "Footwell Lighting"
on the infotainment display, is not visible.
The Footwell Light are not connected yet, could be the cause?
Thanks
best regards
I answer myself, the correct code is,
p_adaption_kundenwunsch_fussraum -> 0.2
In my Golf 7.5 the new menù is in "Ambient Light"
and allows for HMI dimming adjustment
Friend, these commands can I do in OBDeleven?
OBDeleven with PRO license.
@@mrfixpl Amigo, você poderia me ajudar como configurar com o obdeleven pro pra a barra de ajuste do footwell light aparecer na multimédia?
Everything I did is in the description below this video.
@@eliranferreira599 Module: 5F (Information electronics)
Adaptation → Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination → activated
Adaptation → Car_Function_Adaptations_Gen2 - menu_display_ambient_illumination_over_threshold_high → activated
hi, I started coding the procedure as you wrote in detail ... I managed with Vcds to codify only the first part, the long coding, terminal 72 enabling, and the coding for the display control module! ... part concerning the adjustment of the lights ... nn I was able to find the various wordings in the drop-down list .. it is very complicated and long. how can i solve?
thank you
Hi do you have find a solution to change code using VCDS. I have thé sale issue like you i cannot set all paramètre using Vcds ☹️
Hej
Czy taka modyfikacja jest zależna od rodzaju sterownika komfortu?
Z tego co wiem, to wszystkie BCMy powinny to obsłużyć.
Hi mr-fix. I can't change the brightness from the multimedia screen. What is the problem do you have any idea ?
No option on the screen or no reaction from the footwell lights?
@@mrfixpl No reaction from footwell. Menü and slidebar is on the screen.
@@furkankapt2616 Did you fix it?
in my golf mk 7.5 i can't activate ambient lighting-defaultwert ambientprofil fussraum-100%.
does not open ambient lighting says that the system does not respond why?
can you help me I can't get them to light up
Same thing to me on my 2019 Touran… I think we need specifical code
Did all the coding right but the light is still not switching on I’m just confused 🤷🏿♂️ any help please ?
Perform output test to confirm that the circuit works.
Hallo, i want pls the code
It's in the description or at www.ilovecarmods.com
Its A or B or C?
Plug C, pin 72.
Where the f. is part2??
planned. no timeline.
Hello,
I come to ask you because Isearched everywhere and watched a lot of tutorials but I didn’t find what I was looking for
Here is my problem :
I have a Golf 7.5 with basic rear led lights (forums.vwvortex.com/showthread.php?8571473-North-America-gets-screwed-again-here-are-the-LED-lights-for-NA)
I bought original MK7.5 dynamic rear lights, sold with wires (four wires).
For now I plugged all normally without new adding wires, just cuted a little the plug connectors for them to make them compatible.
What works ?
- « general » light works
- Exterior left and right trurn lights work (no dynamic)
Problems/missing :
- No exterior left and right rear turn lights
- No back drive lilghts (onboard lights ON when problem detected : driving back)
What say the install book :
- Climping out all needed plastic
- installing and connecting the « 4 wire harnet » between rear left and right lights and going to BCM
- Code with ODIS
My questions :
- Am I obliged to code with ODIS, it’s a professionnalsofware…
- If obliged to, where must I go to ask for this ? only offical garage VW ?
- If I do all the work but not yet coding, what happen ? only lights onboard ?
- Where can I find tutorials about clipping out wire bottom doors ? (rear door panel it’s ok)
Sorry, it’s long, but I’m in the mess:/ please help me
PS : If you have some information about putting off then on an airbag seats of Golf 7.5… I take…
Mathieu
is it the same on the passat cc 2010?
2010 Passat CC can have the same type of lights but coding will be different for sure.