I like the technique of using screws partially-in to hold stuff up. I have been renovating a bathroom, and could have used that technique twice this week. Thanks for the video!
Thank you for this video. We had a even larger hole to repair and this video in particular was a huge help to us and our hole is now repaired solidly. Thank you again.
I don’t get it. Yes one piece has been sistered with an existing joist but then the other piece is screwed to the floor but it’s effectively got fresh air underneath it. Would it not have been better to find the next joist along and get everything connected to those?
@@stevelopez372 "almost no flex"... and there's the problem. there's should be NO flex. the weight should be supported completely by joists. This may seem like a fix, but over time, that support WILL fail.
can you help me. i tried this but the carpet stuck in the saw and the blade pulled a huge strip of carpet all the way down the hallway. so i guess my first problems i need help with is how do i get the carpet out of the saw while its still on. and my second problem is how can i put the carpet back down and make it look like i didnt touch it. please reply, my dad gets home in an hour.
Excellent. You can also do it when there is no joist on either long side. (Added inset register covers.). One suggestion: I used Titebond III on the surfaces of the horizontal pieces where they attached to the underside of the subfloor.
This is a great repair ideal but instead of doing the second 2x4 like he did if at all possible just cut the plywood square a little larger to the next joist and attach to it or sister it there like he did the first block will make for a much more stable repair
If you cut into the joint about a 1/4 inch will it cause issues later on? My floor has some swollen edges that creak. I worried about cuting into the joist since i dont know how thick the original boards are
Thanks for the video! The music makes me feel like I'm watching an early 90's European soft porn movie. :) Seriously though that was a neat trick holding the board in place with the bar.
Not to criticize but a few more inches over and you could've installed some solid blocking between the floor joists. Then the edge of the subfloor would been solid. This method is fine for a while but it'll loosen up in the future. Just sayin.
The builder was pretty bad laying the 4x8 sheets. First no support in that area then one long running seam that should be staggered for strength. Where was the inspector? BTW nice job.
Why do people think that adding music in the background is a good idea ? I appreciate you trying to help folks out here with their floors however, it is upsetting that you must think that everyone will like your taste in music. It’s your world we just live in it. Kind of reminds me when I was sharing a cubicle with someone at work and the guy I shared a cubicle with, would play music. I did not like it because I was not given a choice whether I wanted to hear the music or not. I kept the sound off while watching your video. Overall thanks for making the video.
Good video but an absolutely awful choice in music which is pulsing in and out and does your head in please remove the music or put something decent on that does not do your head in
Wrong on the 2x4 being held by screws to subflooring... you cut stud to stud like a real man, don't do this if you about doing it right... joist to joist or not at all....
So there is only one edge of that piece of plywood that is going to be solid. Obviously the side that was sistered to the joist. What good does it do to screw a piece of 2X to the floor? There is nothing supporting it! That outta be fun fixing that after all the liquid nail around it. Sorry but this method is useless. Should have cut back to the joist on the other side and sistered it also.
@@lgmnowkondo938 Isn't that reason typically time, effort and cost? It takes longer, costs more and is generally more work to screw the subfloor into place than to use a framing nail gun, but I've yet to see anyone other than you saying it's a no no.
@@CidZAER I had seen a video on youtube where it was expressed that gluing and screwing a subfloor are improper from a structural perspective. Making that structure too rigid may affect some other structures in the house. But...I can't find that video now. Perhaps what you're doing is indeed correct and very good.
I need to do this to my mom's house how difficult is it to do not knowing much ?
if u have left and right hands its not a problem. Good luck!
@TheRageMaker No question is a stupid one as long as it's genuine. Maybe they don't have much experience with powertools and aren't comfortable.
I like the technique of using screws partially-in to hold stuff up. I have been renovating a bathroom, and could have used that technique twice this week. Thanks for the video!
Mark, that was actually my favorite part and I even watched that part again because I thought it was so cleaver.
This is an outstanding video. I learned so much from this! Excellent tip using the pry bar to tighten the brace against the subfloor. Thank you.
Thank you.
Very simple and elegant solution. Thank you for sharing this!
Thank you for this video. We had a even larger hole to repair and this video in particular was a huge help to us and our hole is now repaired solidly.
Thank you again.
That’s why I post my videos. I am very glad that I could help you. Thanks.
Same technique I use for filling old heat register holes. Like the screw and prybar trick. Thanks for the video.
great repair,the only thing i would have done different was used 5 or 6 screws instead of only 3,for more solid repair
If I ever need to fix a flexing floor again I am definitely going to use this technique. Thanks for sharing, EFRSeattle.
I don’t get it. Yes one piece has been sistered with an existing joist but then the other piece is screwed to the floor but it’s effectively got fresh air underneath it. Would it not have been better to find the next joist along and get everything connected to those?
Prob would be better cause it’s relying on the 3 screws to not break off or rip itself through floor
@@jaydenb7515 This works fine with 3/4 plywood almost no flex in short section. Would not work well with osb though.
@@stevelopez372 "almost no flex"... and there's the problem. there's should be NO flex. the weight should be supported completely by joists. This may seem like a fix, but over time, that support WILL fail.
I agree with A C.....
He should of went back 16 inch's to the next joist
Good job solid blocking and fastening, polka music no so good.
Only one side of the replaced piece is actually attached to a joist, though. It is a pretty small area, however, so maybe it will be strong enough.
Mud Marine yup, seen it before, 3/4 inch ply is part of the reason and small area , OSB wouldn’t do in my mind.
can you help me. i tried this but the carpet stuck in the saw and the blade pulled a huge strip of carpet all the way down the hallway. so i guess my first problems i need help with is how do i get the carpet out of the saw while its still on. and my second problem is how can i put the carpet back down and make it look like i didnt touch it. please reply, my dad gets home in an hour.
This is better than buying 1 or 2 sheets of plywood and putting in new sub flooring.
Excellent. You can also do it when there is no joist on either long side. (Added inset register covers.). One suggestion: I used Titebond III on the surfaces of the horizontal pieces where they attached to the underside of the subfloor.
Guess it would of been much easier with unfinished basement. Very nice work.
Perfect. Thank you.
Very good work. #1!
Thanks
Came here to get tips, stayed for the music 🧜🏽♂️
Lol me too
Catchy Tune for sure!
It could have used more cowbell.
This is disco polo.
Awesome video!! Thanks for the tip! 😎
Thanks for sharing this video with us.
Well Done
This is a great repair ideal but instead of doing the second 2x4 like he did if at all possible just cut the plywood square a little larger to the next joist and attach to it or sister it there like he did the first block will make for a much more stable repair
I aside from an interesting video, your music selection was perfect!
Good touch with the glue.
If you cut into the joint about a 1/4 inch will it cause issues later on? My floor has some swollen edges that creak. I worried about cuting into the joist since i dont know how thick the original boards are
Thanks for the video! The music makes me feel like I'm watching an early 90's European soft porn movie. :) Seriously though that was a neat trick holding the board in place with the bar.
Genius ...
Not to criticize but a few more inches over and you could've installed some solid blocking between the floor joists. Then the edge of the subfloor would been solid. This method is fine for a while but it'll loosen up in the future. Just sayin.
It's a very informative video but the music feels like a bad hangover.
@EFRSeattle Should you caulk all of the floorboards when patching up subfloor?
Nope
nice job bro.
Thanks.
Nice job
At the end, He had to pet it like a good floor. Good floor wants a treat??
How would you be able to do this if you have I-joists?
Nice!!! Work...
Nice tricks!!
The builder was pretty bad laying the 4x8 sheets. First no support in that area then one long running seam that should be staggered for strength. Where was the inspector? BTW nice job.
Great soundtrack
Really it’s a video showing you how to hide your drugs
4:03 - I don't understand. The second 2x4 doesn't appear to be attached to a joist so I don't see how that provides any support at all.
Me neither I was asking my self the same question.
The support is pretty much on the screws.
How do you do this with i joists?
I'd rather hear you talkin about the job while you're doing it then listen to this terrible music
Volume button...lol...
You mean "than"?!
@@mikeherbst1825 Makes it sound like he wants to listen to him, and afterward, listen to terrible music.
@@4seeableTV see, you got it!😉
Why do people think that adding music in the background is a good idea ? I appreciate you trying to help folks out here with their floors however, it is upsetting that you must think that everyone will like your taste in music. It’s your world we just live in it. Kind of reminds me when I was sharing a cubicle with someone at work and the guy I shared a cubicle with, would play music. I did not like it because I was not given a choice whether I wanted to hear the music or not. I kept the sound off while watching your video. Overall thanks for making the video.
Bro. Just shut up
Would of been better to go to the next floor joist instead of the middle of the bay and block all the way around....Not the best repair in my opinion
Thanks for your opinion, but next joist ok. This joist not straight line and only one place needs to repair.
@@EFRSeattle But your repair with no support between the joist is now not OK....2 X 4 laid flat floating in the air
@@zeke112964 Thank you again for your comment. I have been using this method for last 12 years, and until that time everything works. Thanks you.
@@EFRSeattle It does work but like I keep telling you it's not a proper repair and will fail eventually.
@@zeke112964 pullout force of each screw is a few hundred pounds and floor loading 50 lb/sf. Small patch area, should be ok.
nice job
rus seattle thanks
So what's 2x4 supporting on basically screwed to subloor
It works with 3/4 plywood which is very stiff in short sections not so good if it was osb.
We have this problem with our floors.
Now you know how to fix it.
Why put a screw in the plywood if you were going to just push it down
pro tip; mute the video, your ears will thank you
I would of just made a box and installed it to joist at least one side if not two sides.
Was the scarface themed music really necessary instead of just explaining what you are doing?
Good video but an absolutely awful choice in music which is pulsing in and out and does your head in please remove the music or put something decent on that does not do your head in
Crawl space FUCK!
Derrr
Couldnt watch it that constant drumming music just didnt cut it with me.
Mute the sound Felipe.
I would prefer verbal explanations to that HORRIBLE music?!?!?
Wrong on the 2x4 being held by screws to subflooring... you cut stud to stud like a real man, don't do this if you about doing it right... joist to joist or not at all....
So there is only one edge of that piece of plywood that is going to be solid. Obviously the side that was sistered to the joist. What good does it do to screw a piece of 2X to the floor? There is nothing supporting it! That outta be fun fixing that after all the liquid nail around it. Sorry but this method is useless. Should have cut back to the joist on the other side and sistered it also.
Need to replace whole floor
I don't think you are supposed to be gluing and screwing subfloor...it's more likely a no no.
lgmnow kondo he put the glue there so it would stop the wood from creaking over time
@@chrisparris5836 if that was the case, then we would all be gluing and screwing subfloor...but we're not. And we're not for a reason.
@@lgmnowkondo938 Isn't that reason typically time, effort and cost? It takes longer, costs more and is generally more work to screw the subfloor into place than to use a framing nail gun, but I've yet to see anyone other than you saying it's a no no.
@@CidZAER I had seen a video on youtube where it was expressed that gluing and screwing a subfloor are improper from a structural perspective. Making that structure too rigid may affect some other structures in the house. But...I can't find that video now. Perhaps what you're doing is indeed correct and very good.
@S Han ur wrong. A nail is much much MUCH more solid and resistant that screws. actual fact
This video is not very helpful without explanations on what you are doing and why.
Scab (also called sistering) a 2x4 onto the joists so the plywood ends have something to sit on. It's a pretty easy concept without explanation.
@@fordrac1ng81 most people don't know what sistering is in the first place.
@@aguyandhiscomputer Yep, that's why we use google.
@@johnnewbold4622 agreed.
@First Last Still not the correct support.
Well Done