This is a useful tool, built after commercially available folders. They are useful for thin flashings which are long, such as 13 feet etc. Great job. Thanks for sharing.
That is such light gauge sheet metal that i could do the same using the edge of a plate or table and bend it using a rubber mallet. I don't think it would fold much thicker than that.
SE OS TUBOS de FIXAÇÃO, FOSSEM SOLDADOS PELO LADO CONTRARIO, SERIA UMA FERRAMENTA MAIS COMPLETA, PODERIAM SER DOBRADAS AS EXTREMIDADES COM 10mm OU 2Omm, O QUE É IMPOSSÍVEL DESTA FORMA......
bet he ruined the bearing with all that un-needed heat, but being for very light work, it will still work, just sad to see all that welding where 2 points were enough
@@nadegdabaikova1456 ты можешь заказать их по своему размеру где катают металлочерепицу и профнастил, а ширину 1.25 придется резать в ручную, или такого же типа есть роликовый листорез , режет четко и быстро прям на скате кровле и резка и сгиб края только прихватываеш или гвоздями или саморезами
@@iancraig1951 HONEST LY IM AN INTERNATIONAL DESIGNER AND HAD USED THESE MACHINE FOR DECADES THE MACHINE HE BUILT IS USELESS AND HARD TO CONROL MUCH MORE IN MASS PRODUCTION IR WILL NOT STAND A CHANCE. OUR COMPANY MADES MILLIONS OD TIN CAN CANNISTERS AND MANY OF OUR SAMPLES AND EVEN PRODUCTION USES THE MACHINE SO I KNOW PRETTY WELL.
This is a useful tool, built after commercially available folders. They are useful for thin flashings which are long, such as 13 feet etc. Great job. Thanks for sharing.
You are welcome!
Well done and this is very useful tool 👍👍
Thank you so much!
Super Idea 🤠 Bravissimo
Thank you so much!
Excellent work.
Thanks!
I like it. It makes a sharp bend with out a lot of cost and simple to make. Ill start one soon.
Thank you so much!
Genius and efisien 👍👍👍👍
Very good!
Thank you!
( RJ )bom dia sua maquina ficou muito SHOW
Amazing Sir
Thank you!
Very usefull tool sir thanks for sharing 😊👍💖👌👍👍
You are welcome!
Great idea!
Thank you!
Great idea.
Thank you!
Absolutely brilliant love it I’ve got to make one cheers well done mate larrysullivan in London
Thank you so much!
Отличный инструмент и видео👍👍👍
Thank you!
Exlente video felicidades
Thank you!
Totally awesome thank you
You are welcome!
Very good idea and nice work 18,guage metal sheet support
Nice work thanks for sharing your stuff
You are welcome!
an amazing tool for light panel work BRILLIANT
Many thanks
so nice
Thanks!
Good idea
Nice tools bro. Thank you for sharing
You are welcome!
Sua idéia amei,só tenho em te agradecer.Mário-São Paulo-Brazil.
You are welcome!
Meus parabéns gostei muito, muito bom mesmo! !!👍👍👍
Me sumo a tus canal me gustan tus trabajos ✌
Thank you so much!
"Parabéns" esse vídeo foi a melhor explicação que vi muito bem detalhados.
Thank you so much!
The best!!!!!
Thank you so much!
apik tor pinter tenan
Thank you!
Amazing tool and video. Cool!
Thank you so much!
Muito bem feito! Mas faltou mais 2 rolamentos na base, pra chapa deslizar melhor.
Many thanks for your suggestions!
Looked at a commercial folding tool for sale a year or so ago; I see where you got the idea.
Nice build! I think i need to copy that. What kind of welder are you using? Never seen one like that.
You can see it at here: bit.ly/30T55h0
PESSOAL É DESSAS PESSOAS QUE O NOSSO PAIS PRECISA .USA A CRIATIVIDADE .PARABÉNS MUITO BOM .
Do you use an argon gas?
Yes, sure.
Buen video amigo una consulta que medida son los rodamientos que usa porfabor
Awesome good luck
Thank you!
Videos muy buenos para los que nos gusta trabajos manuales bien intructivos Gracias.
Thank you so much!
great video thank you for sharing.
That is such light gauge sheet metal that i could do the same using the edge of a plate or table and bend it using a rubber mallet. I don't think it would fold much thicker than that.
You can apply for thicker sheet metal.
@@KwandoTechnic Rods would bend
@@Mike_Hughes No, it'll work on thicker stuff. It won't look great, but if that's all you have and you're in a pinch...
Excelente papi los felicito está muy buena la máquina estoy pensando hacerme una que habló de Costa Rica puntarenas
Muchas gracia por enseñar. ¡La musica es hermosa, quien es el autor ?
Sorry, I don't know, it's youtube music.
can you please let me know what machine torch and filler rod you use and where to find them for sale
You can refer at here: bit.ly/30T55h0
👍👍👍👍👍👍👍
Very nice. Did u make it or buy it?
Thank you. I made it for my work.
Great build, bro! The clamp should add rubber to avoid make scratch on sheet metal.
Thank for nice comment!
❤❤❤
It works fine on flashing but flashing is not generally referred to as "sheet metal". Let's see it work with a piece of 16 GA CRS.
Muito boa tenho uma dessa feita por mim com um detalhe não preciso riscar a peça meço na propria prensa a medida sai exata !!
good tool, thank you !!!
Super Sir, up to what thickness we can bend like this, with this super Tool?
With this tool, you can fold sheet metal with thickness up to 1.2mm
El perno sujetador de las barras, debe estar arriba y no abajo, para facilitar la regulacion
A bit neater than 2 pieces of angle clamped in a vice and a hammer
What number bearing??thanks
i teaching from U😂
parabens ideia brilhante
Thank you so much!
Нууу, имеет право на жизнь 👍!
Genial. Great you are master
Wat can weld machinen you use is it Argon ??? I dont not lm lorning thanks love you channel!!!!😎😎😎😎
Yes, the welder used Argon gas.
What type of welding you use ?
This is my welder: bit.ly/30T55h0
Thank you...
You are welcome!
u can use the edge of the table to do this..
It kind of look good but I think it's suited for only one metal sheet gauge only
I mean... This probably cost 20$... A comparable tool that can do what you say, will cost like 10x :D (20x if talking Draco rol-beaders :P )
Amigo como é o nome dessa maguina de solda e onde encontro pra compra?
You can refer it at here: bit.ly/30T55h0
Learn the difference between TIG and a MIG welding.
You are using a TIG torch like it was a MIG gun!
Good
What welding is that called? TIG?
I use TIG welder as: bit.ly/30T55h0
Wish we could see measurements that would help
Please see it detail in video help me. Thanks!
good
Thank you!
SE OS TUBOS de FIXAÇÃO, FOSSEM SOLDADOS PELO LADO CONTRARIO, SERIA UMA FERRAMENTA MAIS COMPLETA, PODERIAM SER DOBRADAS AS EXTREMIDADES COM 10mm OU 2Omm, O QUE É IMPOSSÍVEL DESTA FORMA......
Bom dia, parabens pelo trabalho desta peca. Ate que tamanho espessura. Ele vira.
bet he ruined the bearing with all that un-needed heat, but being for very light work, it will still work, just sad to see all that welding where 2 points were enough
Что у него за сварка вот ещё бы рассказывал бы атак здорово
I use TIG welder as: bit.ly/30T55h0
прут на котором подшибники не будет долго держать линейность,так как они не квашеные.Прут должен играть.
i like the music while bending
Thank you!
جيد جدا
А гибочный станок не проще?....
Thank for your support. Please tell me if you have any suggestions!
Гибочный гнет 2.50-3 максимум метра, а этот для фальцевой кровли на любую длину
@@исмаилабдуллаев-ь9ю кровельные листы тоже ведь размеры имеют.
@@nadegdabaikova1456 ты можешь заказать их по своему размеру где катают металлочерепицу и профнастил, а ширину 1.25 придется резать в ручную, или такого же типа есть роликовый листорез , режет четко и быстро прям на скате кровле и резка и сгиб края только прихватываеш или гвоздями или саморезами
👍🇰🇿
Sensacional
@Whoop!
⭐⭐⭐⭐⭐
where can I get bearing.
You should find it in home super market or mechanic market.
Berapa harganya bos
Sorry, I don't sale.
Bom d mais vo fazer
You are welcome!
I watched to the end... I think I missed the point of this...
Amajing tullos
jajajajajaja Amazing tool jajajajajjajajajajajajajjajajajajajajaja
а 2ой фадьц на нем не сделаешь!!!!
This video is about 12 minutes too long for something you could do in half the time with a couple of bits of wood .
Many thanks for your advise!
Machine ki cost kitini Kay hay or dilvery Time
९०३९६८५८००
I don't sell. Sorry.
these process is the worst process i had ever seen
I agree--pointless--at least he tried
@@iancraig1951 HONEST LY IM AN INTERNATIONAL DESIGNER AND HAD USED THESE MACHINE FOR DECADES THE MACHINE HE BUILT IS USELESS AND HARD TO CONROL MUCH MORE IN MASS PRODUCTION IR WILL NOT STAND A CHANCE. OUR COMPANY MADES MILLIONS OD TIN CAN CANNISTERS AND MANY OF OUR SAMPLES AND EVEN PRODUCTION USES THE MACHINE SO I KNOW PRETTY WELL.
THIS IS THE WORST TECHNIQUE NOT RELIABLE
❤❤❤❤
Good
Good
Thank you!