Thank you for all of the advice and these videos Chuck! I love your videos for the knowledge AND the inspiration😊 one isn’t much good without the other!
I have a strip of magnet screwed to the edge of a shelf above my work space. I use it to hold tiny pieces of hardware, springs, needles, whatever I don’t want lost. Would be helpful for those little screws you used on that buckle tip.
Tapering the belt was a new set of tricks for me. Definitely useful. My tip for you: Scotch tape. When you take those screws out of the tip, and are going to use them in just a few minutes, take a piece of Scotch tape and just pick the screws up with it, slide them away from your immediate work area, and tape them right to the cutting board. I use about a two inch piece and fold 1/4" of one end back on itself to make a tab so I don't have any trouble pulling the tape up from the board.
You touched on like 3 issues that have really been pissing me off, so thank you. Also, your vids are really easy to watch cause of the energy and clear love you have for both the craft and teaching.
Chuck, always a pleasure and I love the elements! I had a suggestion for a leather element regarding conditioners for leather. Oils, waxes, combinations...when to use one vs the other, before dying, after dying? In lieu of other finishing? I see a lot of inconsistency in opinions out there and would love your take on this. Keep up the good work! I’ve learned a lot!
I had no idea the punch had that adjustability. Thanks. When working with tiny screws, nails, etc I keep a magnet that I've salvaged from a large radio speaker and it will help keep and eye on small, magnetic objects. Keep in mind that this doesn't work on stainless.....some is magnetic/some is not. P.S. Some screws/snaps will take color from "cold blue" that I've used on rusty gun spots to restore color......not all hardware will take it but experiment and see what happens..... Keep the Faith, Tom
Hey Chuck here are three tips for the tipster. Tip #1: Lay those tiny screws on a piece of masking tap to keep them from falling on the floor. Tip #2: if those tiny screws are metal place them in a magnetic bowl. Then they are sure to be there when you need them. Tip #3: Make those mechanical screws magnetic so you can pick the screws up without losing them. Best regards, Richard
Thanks for the tips. I have the same issue with this small screws. People say i have several screws loose so what i do is use a piece of masking tape or scotch tape, put the screws on the sticky side and the stick that to my bench where it won’t get lost.
Hi Chuck - re the compound rotary hole punch, I reckon folk would really appreciate the "optional extra" of replaceable tubes. Model A and Model B... For those of us with arthritis / RSI/small hands etc., the compound style is a game changer.
Love your all your videos especially the shop tips and tricks. If you haven’t done one on this already how about one on tips & tricks for storing leather hides and pieces. Do’s & Dont’s as well as anything special for chrome vs veg vs oil tanned vs etc. Many thanks.
always so detailed and useful as usual！just started leather crafting couple days ago and found out your channel, best choice I made this year so far! Thank you for sharing your valuable experience with us on TH-cam!
Weaver Leathercraft it has been for this past week！have done a cigar pouch for a friend and a fountain pen case, the little tips and details you mentioned it all came out fantastic becuz of your videos！cannot thank you enough！😊
Speaking of shop tips, here is another one: instead of worrying about a sneeze or memory misplacing critical hardware, keep handy a small bowl or, usually more reliable, a weighty magnet, to grab any iron-based item. Even brass- or chrome-looking items are likely to be plated steel rather than solid.
There's a brand of rulers called Alumicutter that's actually very nice for cutting! I found one in a secondhand art shop and it's the most used ruler now. One side is thicker than the other side, almost a quarter inch, and that's meant to be the side to cut on. Also it's non-slip! Though, when it comes to cutting a straight edge into a new side, I use a 6ft level to limit drifting from when you move the ruler down the side.
Red Coyote what kind of knife do you usecover that thickness AND the real thick stuff--10/12 oz. does a box cutter do it? My box cutter handle would clunk against the straight edge and wobble all over. Help!!
Here's a tip for Chuck: Buy an inexpensive magnetized parts bowl. LOL Or, since Chuck will give us DIY tips, get a roll of magnet tape and stick a couple 6" strips side by side on the end of your work bench or on something nearby. Screws won't just roll off the bench. 👍
Chuck here’s “tip” for you. Buy a magnetic parts bowl for your tiny screws, etc. you’ll never lose another one. Get a magnetic screw driver and you’ll be stuck on this tip! Best regards, Richard
@@WeaverLeatherSupply Yanno it was pretty gnarly but the only bad part was that the nurse had to remove a bit of fingernail. That was a new experience, I don't recommend any one try it just for funsies.
I'd be grateful if you did a video about braiding rawhide. I recently made a reata style dog lead, and though I managed to muddle through braiding the core, it was quite a bit of guesswork knowing the rawhide should have.
Thanks Chuck, such great advice. I particularly enjoyed the advice about the bar steel, I’m looking forward to getting into leather crafting, but Would love to spare my fingers as I need them for braille haha I would be interested in hearing more about texture surface treatments for leather. Such as burnishing or bringing out the greens etc. Keep fightin’ the good fight, God bless
Ryan Rohrich agree. For example, how would you finish a piece of armor? How can I preserve the leather and keep it from drying up or rotting without softening the armor?
Thanks a lot Chuck! Weaver gained a lot when you decided to work with them. I appreciate everyone making videos at Weaver but you're like my cool friend giving me plenty of tips and encouragement :) I have got to ask tho: at 2:09 I can see what looks like a hand forged metal spike that you use to remove the hole punch piece. Care to share what it is and what do you use it for? I ask as it was blacksmithing that got me into leatherworking. Thanks for your help and contagious enthusiasm!
Chuck, on the rotating hole punch... I lay a piece of leather 'under' the piece I'm punching through. I have found it first, makes punching through the upper piece easier and second, protects the polished ends of the tubes as I don't need to squeeze hard enough so that those wee tubes meet the metal base. I've never liked that the polished end squeezes down on that metal base. Too easy to ruin the tubes.
I Kawsar Billah Rabbani,,,, I watches your video from Bangladesh for a few days,,, I really enjoyed it and want to work with leather Products so I want your inspiration and advice,,, Million Million thank you...
I wholeheartedly agree about the thicker straight edge! I recently had a blade jump my thin metal ruler. I now have a chunk missing from the tip of my finger, but for awhile I thought I'd lose the whole tip. Ironically, it wasn't leather I was cutting, but paper. If it was leather I'd have been a lot slower and more careful..that stuff is expensive and precious lol.
Use electical tape plastic box or plastic I cream container for my screws or rivits that I sit out on my projects they are alot low than glad storage contaner so they don't tip over. no more lost screws will I am working on something
Chuck your a talented man, but please lose the Craftknives and use the round or head knife, it it so much quicker, I did my saddlery apprenticeship many years ago in England so they are like my right hand, keep the videos coming even after all these years I find you never stop learning.
looking forward to more awesome tips. trying to do my own leather crafting tutorial in our national language. filipino. because i want to help fellow filipinos who are just starting. paulboninvargas zebianmnl
![แฉกลโกงงานวัด 2024 [ โกงมั้ยครับ ep.106 ] | DOM](http://i.ytimg.com/vi/taC5dpP3HXA/mqdefault.jpg)
Always helpful tips and Chuck’s enthusiasm for leather really makes these videos great!
That enthusiasm is what rekindled my interest in leather working.
Best tip? Let”s not sneeze! I simply love this guy! Thank you Chuck! Always something new and interesting, here...
Chucks like the coolest guy I’ve ever seen
Thank you for all of the advice and these videos Chuck! I love your videos for the knowledge AND the inspiration😊 one isn’t much good without the other!
Chuck... Thank you, from South Africa... 👍
Great job as always.
For the small screws. Magnetic screw drivers. Or just put a magnet on the screw driver. Holds enough to get them started.
Helpful tip for small bits and screws, stick them to a piece of painter's tape until you're ready to use them.
Man, this series is simply the BEST!! Thank you, Chuck!
Keep you doing you. Chuck. Addicted still
Chuck, I have to tell you that I love your “Leather Element TIPS”. I always walk away with something I can use. Keep it up. Richard
The bigger point, Chuck, is that you do these videos, and it's good info, thanks for sharing!
I have a strip of magnet screwed to the edge of a shelf above my work space. I use it to hold tiny pieces of hardware, springs, needles, whatever I don’t want lost. Would be helpful for those little screws you used on that buckle tip.
Tapering the belt was a new set of tricks for me. Definitely useful. My tip for you: Scotch tape. When you take those screws out of the tip, and are going to use them in just a few minutes, take a piece of Scotch tape and just pick the screws up with it, slide them away from your immediate work area, and tape them right to the cutting board. I use about a two inch piece and fold 1/4" of one end back on itself to make a tab so I don't have any trouble pulling the tape up from the board.
Thanks, Grady! Great tip!
You touched on like 3 issues that have really been pissing me off, so thank you. Also, your vids are really easy to watch cause of the energy and clear love you have for both the craft and teaching.
Thank you so much!
I love all your tutorials and go to uour videos for every question.Thank You Chuck!
Thank you so much Marie!
thanks for the useable tricks, Chuck, all the best for you and stay healthy...greetings from Germany
Thanks so much Chuck, I especially liked the advice on belt tips and metal straight edges. I’m off to the hardware store!
Thank you, Terry!
You never let us down ,whatever I need to know about my leather making I check you out.Never disappointed ,thank you.
Dam u chuck! If u keep putting out these cool videos I'm gonna have to get into leather craft
Chuck, always a pleasure and I love the elements! I had a suggestion for a leather element regarding conditioners for leather. Oils, waxes, combinations...when to use one vs the other, before dying, after dying? In lieu of other finishing? I see a lot of inconsistency in opinions out there and would love your take on this. Keep up the good work! I’ve learned a lot!
I second this request
Always look forward to your videos. I always learn something new. Thank you!
Thank you so much!
This is one of your best videos yet. A lot of useful information without any fluff. Thumbs up!
Thank you so much, Lex!
Very nice. Thank you for the video. I juat started thia hobby on My own so your videos are very helpful.
I had no idea the punch had that adjustability. Thanks. When working with tiny screws, nails, etc I keep a magnet that I've salvaged from a large radio speaker and it will help keep and eye on small, magnetic objects. Keep in mind that this doesn't work on stainless.....some is magnetic/some is not. P.S. Some screws/snaps will take color from "cold blue" that I've used on rusty gun spots to restore color......not all hardware will take it but experiment and see what happens..... Keep the Faith, Tom
Thank you, Tom!
Thanks again. I always like your "shop tips", I either learn something, or remember something I have forgotten. Either way, it is good.
Good to hear, thank you!
A magnetic dish corrals those set screws very well so long as they aren't 100% stainless steel
Good morning, knowledge is everything. Thank you for sharing simpler techniques more escencials for a job with perfect finish. Great week, everyone.🇧🇷
Thank you for watching!
Always an enjoyable time with Chuck! Thanks for the tips.
Chuck's the greatest. Iv'e learned everything I know from you. Seriously.
Definitely Awesome 👌 Tips & Tricks.
Hey Chuck here are three tips for the tipster. Tip #1: Lay those tiny screws on a piece of masking tap to keep them from falling on the floor. Tip #2: if those tiny screws are metal place them in a magnetic bowl. Then they are sure to be there when you need them. Tip #3: Make those mechanical screws magnetic so you can pick the screws up without losing them. Best regards, Richard
Hey Chuck! Could you do a quick video to show us your belt? I've always admired it, would be great to see it up close!
Cheers
Thank you for the belt tip trick. Now I know how to do it! And I did lose one of my screws last weekend.
Thanks for the tips. I have the same issue with this small screws. People say i have several screws loose so what i do is use a piece of masking tape or scotch tape, put the screws on the sticky side and the stick that to my bench where it won’t get lost.
Hi Chuck - re the compound rotary hole punch, I reckon folk would really appreciate the "optional extra" of replaceable tubes. Model A and Model B... For those of us with arthritis / RSI/small hands etc., the compound style is a game changer.
Take a shot for everytime chuck almost lost those set screws
The things you just don't know. It's really nice to have a teacher being like, yes this!
nice tricks, thanks Chuck
Love your all your videos especially the shop tips and tricks. If you haven’t done one on this already how about one on tips & tricks for storing leather hides and pieces. Do’s & Dont’s as well as anything special for chrome vs veg vs oil tanned vs etc. Many thanks.
You are a great teacher Chuck. Thank you.
I appreciate that!
Excellent tips, Chuck. I'll use them all. Thanks.
Thank you for the tips, I'll probably use it all. It's nice when a master at the craft gives tips and tricks.
always so detailed and useful as usual！just started leather crafting couple days ago and found out your channel, best choice I made this year so far! Thank you for sharing your valuable experience with us on TH-cam!
Welcome aboard! Thank you so much for watching and I hope they've been helpful!
Weaver Leathercraft it has been for this past week！have done a cigar pouch for a friend and a fountain pen case, the little tips and details you mentioned it all came out fantastic becuz of your videos！cannot thank you enough！😊
Speaking of shop tips, here is another one: instead of worrying about a sneeze or memory misplacing critical hardware, keep handy a small bowl or, usually more reliable, a weighty magnet, to grab any iron-based item. Even brass- or chrome-looking items are likely to be plated steel rather than solid.
Great tip!
Use low strength Loctite on screw back findings.
Always a pleasure to watch u work thanx for the great tips!!
Great tips. Getting into making holsters.
If you keep a pickle jar lid or something like it handy for concho screws etc. they don't roll away.
Good idea, thanks!
There's a brand of rulers called Alumicutter that's actually very nice for cutting! I found one in a secondhand art shop and it's the most used ruler now. One side is thicker than the other side, almost a quarter inch, and that's meant to be the side to cut on. Also it's non-slip!
Though, when it comes to cutting a straight edge into a new side, I use a 6ft level to limit drifting from when you move the ruler down the side.
Red Coyote what kind of knife do you usecover that thickness AND the real thick stuff--10/12 oz. does a box cutter do it? My box cutter handle would clunk against the straight edge and wobble all over. Help!!
As always. Great information... Thank you for the tips and tricks. Learned something
Great video. I’m subscribing right now.
Here's a tip for Chuck: Buy an inexpensive magnetized parts bowl. LOL Or, since Chuck will give us DIY tips, get a roll of magnet tape and stick a couple 6" strips side by side on the end of your work bench or on something nearby. Screws won't just roll off the bench. 👍
Yeah. What this guy said...
Except a lot of the hardware for leather is brass.
Hi, Chuck I always keep a few magnets within reach in my shop, helps keeping small steel parts from disappearing.
Good tip!
Chuck here’s “tip” for you. Buy a magnetic parts bowl for your tiny screws, etc. you’ll never lose another one. Get a magnetic screw driver and you’ll be stuck on this tip!
Best regards, Richard
Great tips as usual. Well presented Thanks.
Thank you for this, it really helped
I feel ya man, I had a blade jump an edge a few months ago, cut the snot out of my index index finger.
Ouch! Hope you're all healed up!
@@WeaverLeatherSupply Yanno it was pretty gnarly but the only bad part was that the nurse had to remove a bit of fingernail. That was a new experience, I don't recommend any one try it just for funsies.
This guy is fantastic
I'd be grateful if you did a video about braiding rawhide. I recently made a reata style dog lead, and though I managed to muddle through braiding the core, it was quite a bit of guesswork knowing the rawhide should have.
Thank you for the suggestion!
Thanks Chuck, such great advice. I particularly enjoyed the advice about the bar steel, I’m looking forward to getting into leather crafting, but Would love to spare my fingers as I need them for braille haha I would be interested in hearing more about texture surface treatments for leather. Such as burnishing or bringing out the greens etc. Keep fightin’ the good fight, God bless
Ryan Rohrich agree. For example, how would you finish a piece of armor? How can I preserve the leather and keep it from drying up or rotting without softening the armor?
Thanks a lot Chuck! Weaver gained a lot when you decided to work with them. I appreciate everyone making videos at Weaver but you're like my cool friend giving me plenty of tips and encouragement :) I have got to ask tho: at 2:09 I can see what looks like a hand forged metal spike that you use to remove the hole punch piece. Care to share what it is and what do you use it for? I ask as it was blacksmithing that got me into leatherworking. Thanks for your help and contagious enthusiasm!
i love bringing up the finger. Have cut the tip of my finger off twice due to a jump.
Oh man - so sorry to hear that! I think we've all had those moments but they are not fun!
great tips chuck as always
Thank you, Jerry!
I enjoy your videos thanx..and when I have small screws I lay down a piece of double sided tape
Good tip!
Chuck, on the rotating hole punch... I lay a piece of leather 'under' the piece I'm punching through. I have found it first, makes punching through the upper piece easier and second, protects the polished ends of the tubes as I don't need to squeeze hard enough so that those wee tubes meet the metal base. I've never liked that the polished end squeezes down on that metal base. Too easy to ruin the tubes.
Great tip - thank you!
Well done, loved the tips, thank you.
Chuck rocks!
I Kawsar Billah Rabbani,,,, I watches your video from Bangladesh for a few days,,,
I really enjoyed it and want to work with leather Products so I want your inspiration and advice,,, Million Million thank you...
Thanks for the info! 😃👍🏻👊🏻
I wholeheartedly agree about the thicker straight edge! I recently had a blade jump my thin metal ruler. I now have a chunk missing from the tip of my finger, but for awhile I thought I'd lose the whole tip. Ironically, it wasn't leather I was cutting, but paper. If it was leather I'd have been a lot slower and more careful..that stuff is expensive and precious lol.
Glad you're ok! Such a scary feeling!
Great tips. Thanks.
I tape little screws/parts to a scrap of tape and tape down to my table so I don't lose them!
Killer tips, thanks!
8:40 I have a small magnet to hold screws like that.
Helpful vid. Thanks.
Glad it was helpful!
Use electical tape plastic box or plastic I cream container for my screws or rivits that I sit out on my projects they are alot low than glad storage contaner so they don't tip over. no more lost screws will I am working on something
Chuck I just can't bring my self to sand those screw heads I just set the screws below the surface no matter how much work it takes . Happy trails
Mike Boone me too. I would have scratched that chrome on the first pass.
I want Chuck to read my eulogy at my funeral.
Good tips!!!!
TY
Good tips
Chuck needs a magnet set into the workbench for those pesky flying tiny screws. :)
Good grief I bought 4 rotary punches that just wouldn't do the job. Thank you so much Chuck
What are the advantages of a maul over mallet?
How about making a leather ivy cap with silk liner
Do you have any tricks or tips on beveling the edges of lace?
Good!
Chuck your a talented man, but please lose the Craftknives and use the round or head knife, it it so much quicker, I did my saddlery apprenticeship many years ago in England so they are like my right hand, keep the videos coming even after all these years I find you never stop learning.
What size snaps with what weight leather ??
My blade jumped my straight edge and cut offed the tip off finger. So humiliating
Oh no - hope you're all healed up! That is such an awful feeling but it happens so fast!
looking forward to more awesome tips. trying to do my own leather crafting tutorial in our national language. filipino. because i want to help fellow filipinos who are just starting.
paulboninvargas
zebianmnl