How to Connect RadioLink RC8X with TBS Crossfire via CRSF or PPM?
ฝัง
- เผยแพร่เมื่อ 18 พ.ย. 2024
- How to connect RadioLink RC8X with TBS Crossfire via CRSF or PPM?
TBS Crossfire supports PPM and CRSF signal input. So you can connect RC8X with it via PPM or CRSF. I’ll introduce the connection of the two signals.
1. Connect RC8X with TBS Crossfire via CRSF signal.
Connect RC8X DSC port with the audio cable, which has ground wire and signal wire. Here it is. Pay attention not to plug it into Earphone jack.
Modify the other end of the audio cable. Solder two pins to the wires, and then connect them to GND and CRSF on TBS Crossfire. Here is the diagram of TBS Crossfire. So please distinguish the two cables to confirm which one is ground wire or signal wire. If the connection is reversed, no signal will be found.(Do not confirm the cable type via color of it)
Here is ground cable, connect it to GND. Here is signal cable, connect it to CRSF.
RC Input and EXP. Port connects well too. So the connection is done.
Now, power on TBS Crossfire and RC8X. It shows no signal in RC Input. So we need to select the right signal output on RC8X.
Enter System menu-- External input output. Set the protocol output mode to CRSF. Now it shows CRSF in RC Input, which means the connection is successful.
2. We can also connect RC8X with TBS Crossfire via PPM signal.
Just need to connect the signal wire and ground wire to PPM and GND respectively. Plug the signal wire into PPM. Then the connection is done.
It shows no signal in RC Input. So we need to select PPM output on RC8X.
Set the protocol output mode to PPM-OUT. Now it shows PPM in RC Input, which means the connection is successful.
By the way, if you are not good at modifying the cable, you can connect them with the cable that comes with TBS Crossfire. Here it is.
Connect one end to DSC port of RC8X, and the other end to RC Input. Then set the protocol output mode to PPM-OUT on RC8X. It also shows PPM in RC Input, which means the connection is successful.
So when you connect any other module to RC8X, you can check its diagram and refer to this tutorial to connect them.
For more details of RadioLink RC8X:
www.radiolink....
Purchase link of RadioLink RC8X:
www.aliexpress...
You can send mails to after_service@radiolink.com.cn if you have any questions during using our products.
#fpvracing #fpv#rctransmitter #radiolink #rc8x
Thanks this is helpful for setting up the transmitter side. What about the receiver? I'm trying to set this up for a RC car. Assuming it requires a TBS crossfire receiver. Do we unplug the RC8X receiver? Can you explain?
Hi, sir. If you connect TBS Crossfire to RC8X, you don't need to use R8FG receiver. You just need to use the crossfire receiver. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@RCGirl Did you have a chance to see if the crossfire module will work with the R8FG receivers? I have many speed run cars running the R8FG and need the crossfire module for more range but for the price of the module and their $130 receivers I can just switch to futaba 🤣
Will the radiolink R8FG receiver bind to the tbs crossfire module? I know tbs has their own receivers, but I want to use my radiolink R8FG receivers with the tbs crossfire module.
Hi, sir. Sorry you cannot bind R8FG to TBS Crossfire module. When you use TBS Crossfire module, please use their own receiver. If there is any question, please feel free to contact us. Our email is after_service@radiolink.com.cn
Hello, does the TBS CROSSFIRE MICRO TX V2 also work with the radiolink?
Hi, sir. Yes. TBS CROSSFIRE MICRO TX V2 also work with the RadioLink transmitters. You just need to check the digram of it, and follow this tutorial to connect them. The connection method is similar. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
What is the signal/polarity of the 3.5mm plug? Tip signal and sleeve ground?
Hi, sir. Yes. For the connector of DSC port of RC8X, it has ground and signal. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Can I use head track with some long range module like crossfire or express LRS at the same time? I think both of them uses DSC port right?
Hi, sir. Sorry you cannot use head track and crossfire or express LRS at the same time. You can only select one function to use. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
make a video on how to setup the TBS CROSSFIRE MICRO TX V2 with the rc8x please
Hi, sir, The tutorial is similar to this one. You just need to check the Interface definition of the TBS CROSSFIRE MICRO TX V2. Then you can follow this tutorial to connect them. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Can i use ELRS module like Jumper AION nano with CSRF to DCS port?
Its support or not?
Hi, sir. Yes. You can connect TBS Crossfire or ELRS module to RC8X. Because RC8X supports CRSF signal. Here is a tutorial for your reference. th-cam.com/video/W_5y_OxVn2o/w-d-xo.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Does this work with R8FG 8 receiver?
Hi, sir. RC8X can work with R8FG/R8F/R8EF/R7FG/R6FG/R6F/R4FGM/R4F receiver. www.radiolink.com/rc8x_specifications When you connect TBS Crossfire to it, you need to use TBS Crossfire receiver. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Does this work on the older transmitters also?
The older RadioLink transmitters do ppm out. So it does work as long as the module supports it and you have the correct cable.
-Crossfire module supports ppm
-R9 module supports ppm
-Dragonlink does as well with the correct firmware.
Hope this helps 🤙
@@ChaddRainsFPV your the best that does help quite a bit actually
Hi, yes. You can also connect TBS Crossfire to older transmitter such as RC6GS. Make sure you have installed the right firmware. Here is a tutorial for you: th-cam.com/video/6vt5QexQSQs/w-d-xo.html
Does ELRS module supports PPM?
Merhaba kolay gelsin benim at9 kumanda var. 1kanalda 3 adet servoyu aynı anda hareket etttirip sonrada ayrı kanallarda ayrı ayrı hareket ettirmek için nasıl bir ayar yapmam gerekiyor
Hi, sir. Thank you for your support. You can set PROG,MIX function. And you may need to set 2 mixes. Here is the tutorial of PROG,MIX for your reference: th-cam.com/video/DKTS3X66tCE/w-d-xo.html If any question when using RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official teşekkür ediyorum
@@kasifyldrm1981 Our pleasure. Any question please feel free to contact us.
@@Radiolink_official ilginiz için teşekkür ederim tamam
Tekrardan merhaba video izledim ve bu ayarlamayı yaptım. yalnız ben bu sistemde 3 adet servoyu hareket ettirmek istiyorum .siz 8 ci kanalda yapmışsınız. Ben atıyorum 6 cı 7 ci 8 ci kanallarda yapmak istiyorum