SRAM Force eTap AXS Rear Derailleur Fitting Guide

SRAM Force eTap AXS Rear Derailleur Fitting Guide If you find the videos helpful and would like to make a small donation to help support the channel you can do so here www.paypal.com...
Buy me a coffee
www.buymeacoff...
Show your support via the Patreon page
/ freetocycle
Follow me on Instagram
www.instagram....
[e-mail]
Thanks for watching.

[@Andyange]

These videos are better than the sram instructional videos.

[@mandyo9690]

Thanks, just the help I am looking for after removing the derailleur for travel, and now needing a bit of adjustment.

[@katdam3868]

Thanks for explaining the tab that meets up with the b-screw. That was my problem and no one ever noted that part.

[@recordball]

Thanks bud! Showing how the micro adjust button works with the shifter off in your hand is much more understandable then other videos I watched.

[@billz410]

Long live single-speed!!!! LOL
On a more serious note....very informative, to the point explanation. Very well done. Thank you!

[@tstark05]

I own the force xplr derialluer which I think has the orbital damper. Do you know if these have a cage lock? It’s quite a pain switch out wheels without a cage lock

[@FreeToCycle]

The Force xplr uses a fluid clutch damper, there is no cage lockout on the derailleur! Make sure you shift to the 10 tooth on the cassette to make it easier to remove the rear wheel.

[@generalpompeyo]

Hey thands for the video. One question, I recently fell on my bike, and the derailleur had a decent impact (its the same one). It seems to be working fine for now, but do you think I could have problems later on?

[@cristianpena9179]

Dear F to Cycle. Thanks on all your kwnoledgey videos.
I see you set the top jockey wheel in line with the 10 cog sprocket. How do you do that? Mine is a Hole sprocket down and can not set them properly, is a XPLR RD. Thanks a lot

[@FreeToCycle]

Adjust the H limit screw on the derailleur!

[@cristianpena9179]

@@FreeToCycle just like a regular mechanical RD?

[@CanTURKeyed]

hi sir; ı ll make 30T->36T whats mm needed between tip of teeths 1 st cog and guide pulley _? thank you

[@davidsantos5516]

Good vid...
Please help where can i get that plastic (red) tooth hight "ruler," for bigest (28 or 30) tooth, thank you

[@FreeToCycle]

Available online search for SRAM red/force eTap axs derailleur chain gap adjustment tool.

[@PaulPattison-uf4zm]

Hi,
What is the difference between the 33t max and 36t max rear derailleur?
Thanks

[@dndhm]

3t

[@danfin0582]

On what front chain ring does the chain have to sit when adjusting the chain gap on the Rear Derailleur in case of a 2x set up?
On the bigger chain ring or on the small chain ring? On my new Cannondale Systemsix the chain touches the frame in the highest gear
(front = big chain ring / back = smallest chain ring). This couldnt be normal an I think the chain gap is to small.

[@FreeToCycle]

On the Inner front chainring and the largest rear sprocket!

[@0321recon]

Can you put a bigger cassette than 36t on the SRAM Force eTap AXS?

[@ElliotWrightUK]

Not with the road derailleurs, but you can mix and match components. You'd need a new rear derailleur and cassette at least.

[@bonn1771]

solid video thank you
learned a few things

[@johnburgess506]

Help, I don’t have shifters as I have TT bike with clics how do you micro adjust ?

[@FreeToCycle]

With the SRAM BlipBox!

[@poltergeistducs2948]

How to adjust b limit screw without the tool??

[@vd0o666]

I can't get mine to shift in to the largest cog 36t what should i do?

[@stephenmcmenamin4802]

How did you shift under the biggest cog on the cassette before the chain went on?

[@FreeToCycle]

Yes!

[@ww4407]

Great video! Have you done a video on sizing the flat top chain for a Force eTap AXS groupset?

[@FreeToCycle]

Not for the Force eTap itself! It’s the same basic process as for sizing any bicycle chain.