Thanks for this - definitely the simplest roller solution I have seen. Commercial products run at $10 a foot length in the US where as 2 inch pipe is under $20 for 10 feet so 1/5 that price. For shorter sections you could probably use smaller diameter too. Test a length and see how much it bends but 2" (5 cm) diameter seems about right.
Thank you for showing a roll bar that doesn’t contain a small bar and a wider bar (like most construction are made). Your idea is a lot cheaper and doable: even for me; a widow mom of two without handymen around. The trick though to have a round wooden piece inside the bar is challenging: I didn’t get how you cut them out into a perfect fit (stupid me will have to watch the video over and over again)🤦🏻♀️
hehe.. Thank you.. I use caliper to measure pipe diameter.. Or you can draw piping size direct on wood. Then cut follow the drawing. Use sand paper to rub around the wood to fit inside the pipe.
Your husband is very clever and handy. Your cat looks sweet but mischievous. My cats can't be trusted not to jump deck rail. I've been looking for ideas of things I can do myself but I am not clever and don't have many tools besides a butter knife & my high heels but I do have a dremel. Thank you for this video and the interesting idea.
Loved your video and how you did your system with the pipes. But I wish you would write the steps down for us. Video was hard to see what he did to the ends of the round wood once he had them in there with glue and how he cut the round wood. For beginners, would be nice to write down the details that is often missed by speeding up the video. Thank you for the idea. But if I can get more details on those parts I mentioned would be wonderful. Also how he put the ends up, like how he attaches them to the wood part.
Thank You so much for your appreciation . first thing, for the rounded wood i use jig saw like what you can see on video. just cut the wood use jig saw follow the marking you had done. After finish cut, use sand paper to make sure the wood surface can fit inside the pipe. Second, After i glued the wood inside the pipe, i used small nail to make sure the rounded wood is really hard attached to the pipe. After that u need to make a hole center of the round wood (the hole must be bigger than screw/nail you use to attached to the wood later).. Third, how i attached the roller to the wood.. i just cut 3X1 inch wood( depend on your fence size)After that, i used screw size 2 inch to attached to the 3x1 wood.(or you can use 2 inch nail to attached the roller to the 3x1 wood).I think its really hard to explain without video..hehe...so i decide to make 1 video later to explain how i attached the all things...make sure u follow my next video..i apologize to my first video. i hope i will make 1 video that can help you and other people later...i will try to make as soon as possible....
I really need to do this for my home. Hope u can show again in clearer video on how to attached that roller to the fence & how the roller can move freely.
Does anyone understand how he got them so close together? When the first one was up you could see the screw sticking out. When they butt up against each other where did that screw head go? And what space was there for a screw head going into the other one next to it?
Sorry for my first video. I will try to make another video to explain how i attached the all things. I hope i can help you later. Make sure you follow my next video. Thank you sir
Ele colocou um parafuso no centro do diametro do tubo sendo assim o tubo gira pelo centro do diametro. Voce pode usar a ideia e usar garrafas pet, perfurando o centro do fundo das garrafas pet e as colocando em linha sobre um fio, corda ou vareta de bambu ou barras finas de ferro.
Every cat need space to climb ,and after climb he also need a space to jump. Cat not like a spiderman..hehe..That why i put a small vase with leaf and put a net around the vase. U need watch the video again for more detail. Just pause the video and zoom it , see the detail.
If you look closely, where the pots are, behind them there’s A brown gated fence like. Looks like it’s made out of wood, maybe hard to see it, So the cats cannot jump over where the pots are.
Are u sure? Are u already come to my house and see? Bring ur cat come to my house and we will see together ..please come..my content i made is free. Nobody pay for me..just sharing
An end cap is probably not thick enough to support a nail without it just wobbling around. It might work. I would probably use a bolt or piece of "all thread" with nuts and washers at each end to keep it snug. If it doesn't spin well I'd use a piece of busing where it passes through the support bracket, or file down the thread to be smooth.
i just show the real roller that u can buy at any online shop.. its up to you...my cat fail to climb the fence right now and i happy with my choice and my work.. Nobody paid me for my video and my work . I m just sharing.. until now, i still using this roller...
It was a nice video and everything, but I'd like to see the fence working at your place, with your own cats, since the video in the end is a device that was made for this purpose.
Thanks for your feedback. My cats don't want to try it anymore after failed to jump several time...it just happened quick in front of us.i don't have cctv to record the situation.😅 Now my cat is getting to fat and getting sleepy every time.just eat and sleep...🤭
hye bimbajazz..i m very sorry for the fast video..In youtube setting you can try make the video play in low speed.maybe can help you to see the detail.
![[TH] 2024 PMWC x EWC Group Stage Day 3 | PUBG MOBILE WORLD CUP x ESPORTS WORLD CUP](http://i.ytimg.com/vi/VnOqutfqWqU/mqdefault.jpg)
The little boy "helping" his dad is adorable.
tq2
Brilliant! Just plain brilliant. Nothing like staying one paw print ahead of our fur babies.... for their own safety.
Is there a video of the cat failing?
@@musadamar8218 you really want to see cats falling don’t you 🤣
Thanks for this - definitely the simplest roller solution I have seen. Commercial products run at $10 a foot length in the US where as 2 inch pipe is under $20 for 10 feet so 1/5 that price. For shorter sections you could probably use smaller diameter too. Test a length and see how much it bends but 2" (5 cm) diameter seems about right.
Thank you for showing a roll bar that doesn’t contain a small bar and a wider bar (like most construction are made). Your idea is a lot cheaper and doable: even for me; a widow mom of two without handymen around. The trick though to have a round wooden piece inside the bar is challenging: I didn’t get how you cut them out into a perfect fit (stupid me will have to watch the video over and over again)🤦🏻♀️
hehe.. Thank you.. I use caliper to measure pipe diameter.. Or you can draw piping size direct on wood. Then cut follow the drawing. Use sand paper to rub around the wood to fit inside the pipe.
@@mrfadzliyusoff9645 Oh wow! Thanks for the advice👍🏼 Im going to have a nice careless summer this year; thanks to you!☺️
Gonna do this! Best video about this method yet. Mahalo!
Your husband is very clever and handy. Your cat looks sweet but mischievous. My cats can't be trusted not to jump deck rail. I've been looking for ideas of things I can do myself but I am not clever and don't have many tools besides a butter knife & my high heels but I do have a dremel. Thank you for this video and the interesting idea.
Loved your video and how you did your system with the pipes. But I wish you would write the steps down for us. Video was hard to see what he did to the ends of the round wood once he had them in there with glue and how he cut the round wood. For beginners, would be nice to write down the details that is often missed by speeding up the video. Thank you for the idea. But if I can get more details on those parts I mentioned would be wonderful. Also how he put the ends up, like how he attaches them to the wood part.
Thank You so much for your appreciation
.
first thing, for the rounded wood i use jig saw like what you can see on video. just cut the wood use jig saw follow the marking you had done. After finish cut, use sand paper to make sure the wood surface can fit inside the pipe.
Second, After i glued the wood inside the pipe, i used small nail to make sure the rounded wood is really hard attached to the pipe. After that u need to make a hole center of the round wood (the hole must be bigger than screw/nail you use to attached to the wood later)..
Third, how i attached the roller to the wood..
i just cut 3X1 inch wood( depend on your fence size)After that, i used screw size 2 inch to attached to the 3x1 wood.(or you can use 2 inch nail to attached the roller to the 3x1 wood).I think its really hard to explain without video..hehe...so i decide to make 1 video later to explain how i attached the all things...make sure u follow my next video..i apologize to my first video. i hope i will make 1 video that can help you and other people later...i will try to make as soon as possible....
Thank you so much
It's a good and cheap solution, you don't need the expensive.
I really need to do this for my home. Hope u can show again in clearer video on how to attached that roller to the fence & how the roller can move freely.
Thank you so very much!
Qué ingenioso el hombre!
Muchicimas gracias por compartir su conocimiento! Le quedo excelente muy lindo , intentaré hacerlo en mi patio!! :)
Thank you🤗
Did you ever make the second video explaining the steps to the cat barrier?
Great idea, using less materials than other solutions I have seen
Thank for that video. We moving to a 6 floor appartement iam so scare they going on the fences.
Very good. Thank you.
Great idea thank you
tq2
😀😀nice method...Hey I really liked the background music..Like it goes like hmmm..What song is that???
Great video sister
Does anyone understand how he got them so close together? When the first one was up you could see the screw sticking out. When they butt up against each other where did that screw head go? And what space was there for a screw head going into the other one next to it?
Could you show the end of the tube and how it spin freely, please?
Sorry for my first video. I will try to make another video to explain how i attached the all things. I hope i can help you later. Make sure you follow my next video. Thank you sir
Please. Would like to see it as well. Thanks for your great idea.
Ele colocou um parafuso no centro do diametro do tubo sendo assim o tubo gira pelo centro do diametro. Voce pode usar a ideia e usar garrafas pet, perfurando o centro do fundo das garrafas pet e as colocando em linha sobre um fio, corda ou vareta de bambu ou barras finas de ferro.
i loved!!!
Gracias👍
What's the name of the humming song used for this video?
song from video editor(Filmora)..not sure the song name
@@mrfadzliyusoff9645 I finally found it thanks to you. It's called "Lullaby" by Benjamin Thompson.
I seriously doubt this would stop a determined cat. The cat can climb to the top rail of the gate, and then simply jump over the roller.
when the roller spins, the cat still can climb over the roller?😅
@@mrfadzliyusoff9645 When the cat is on the top rail of the fence, he can jump OVER the roller without even touching it.
@@lwh7301 ohh, u mean the fence post from left and right?
Every cat need space to climb ,and after climb he also need a space to jump. Cat not like a spiderman..hehe..That why i put a small vase with leaf and put a net around the vase. U need watch the video again for more detail. Just pause the video and zoom it , see the detail.
Quantos metros tem o cano?
bravo
Her accent is neat
thank u so much..
Hi I didn’t get how does it roll, can someone explain to me?
joe que buena idea
How much is it?
gostei parabéns.
idea is great, but won't cat climb over pots on the sides?
If you look closely there is a fence on the other side of the pots.
@@barbarat5729 yes..your answer is correct
If you look closely, where the pots are, behind them there’s A brown gated fence like. Looks like it’s made out of wood, maybe hard to see it, So the cats cannot jump over where the pots are.
Oops sorry, didn’t realize someone already answered that. I don’t know how to erase my answer, so I just wanna apologize.
the cat can still escape into the pots lol 🤣
Are u sure? Are u already come to my house and see? Bring ur cat come to my house and we will see together ..please come..my content i made is free. Nobody pay for me..just sharing
Shokran.
Trump: It's good enough but it should've been ten feet taller!
I might try this my cats get out n stray cats beat him up this may help
why just not to use end cap (1.5$) rather than diy round wooden thing....
An end cap is probably not thick enough to support a nail without it just wobbling around. It might work. I would probably use a bolt or piece of "all thread" with nuts and washers at each end to keep it snug. If it doesn't spin well I'd use a piece of busing where it passes through the support bracket, or file down the thread to be smooth.
It will not work, the roller less spin, use bearing, should easily spin like fidget spiner
Why did you show somebody else's fence at the end? Yours must not have worked.
i just show the real roller that u can buy at any online shop.. its up to you...my cat fail to climb the fence right now and i happy with my choice and my work.. Nobody paid me for my video and my work . I m just sharing.. until now, i still using this roller...
Добре вам,4 метри паркану,а в мене 300 метрів,не вистачить ні сил ні натхнення 😂😂😂😂😂.
Very fast I can not see well
It was a nice video and everything, but I'd like to see the fence working at your place, with your own cats, since the video in the end is a device that was made for this purpose.
Thanks for your feedback. My cats don't want to try it anymore after failed to jump several time...it just happened quick in front of us.i don't have cctv to record the situation.😅
Now my cat is getting to fat and getting sleepy every time.just eat and sleep...🤭
I think this interesting but Sorry the video runs too fast and some important steps we cannot see , for I am not very Expert .
hye bimbajazz..i m very sorry for the fast video..In youtube setting you can try make the video play in low speed.maybe can help you to see the detail.