YEAH! These presets are a HUGE reason to purchase AOS products. Chris, your expertise canned into presets is incredibly valuable. I’ve been writing PID code, tweaking PID values, etc. since 2009 and I’m sick of it! I’m retired from aviation and just want to fly… AOS Rocks! And so do their Hoodies! Buy one today!
After hours of tuning my 5 v5 I found these presets and tried them out - I must admit, I kinda failed with my tuning 😂 Thank you so much for your work! Absolutely smooth with Xing2‘s 1755kv and 6s 1300mAh‘s!
I'm getting a mixer mode problem. It needs 4 motor resources but current firmware provides 0. Need to define a custom mmix before changing mixer mode. Check configuration and add the required motor resources. I'm not sure what to do here?
Man, thanks! Built a BFPV Meteor 75 Pro Walksnail a year ago and it has always had a slight wobble only noticeable when hovering no matter what I did. Updated to 4.5.0, still wobbled. Applied your standard 1S whoop tune, fixed!
Just ordered an AOS UL10 frame. Going to build it up with gear I already have on hand : Goku F722 stack w/ 50A ESC, BH 3115 1050kv motors (on 5S), Walksnail video. Doesn't look like there are any presets for this frame. guess I can use the UL7 settings as a starting point.
Any presets to take 2024 Mobula 6 HDZ Frestyle for indoors flying beginner learning Acro? Was thinking to scale throttle to 65%, mid to 0% with 0.5 expo; and do 50, 450 and 0.5 expo on(pitch, roll and yaw).
Chris, I’m just about to build with the components below, will the presets be okay with this? AOS 5 V5, Speedybee F405 V4 60amp esc, DJI 03, Supanova 2207 1950, ELRS. Any help would be great.
Chris, I’m pretty distraught and don’t know what happened. I have the AOS 5v5 frame with the supernova motors and not 10 sec into my first flight it dropped out of the sky and I found that two motors were burnt up. I used your tune in this video. This is my first build and it’s left me pretty low. Any thoughts? I would SO appreciate your help.
I just finished the same build, I noticed the motors sounded like they were “grinding” and then checked and they were hot. I’m thinking the supernovas need a master multiplier of less than 1.0 as when I switched back to the default beta flight tune, the motors sounded normal again. Hopefully Chris can weigh in on this.
I'm looking at which preset should match for my "AOS 5 v5" and the preset names and descriptions confuse me a little. There is "AOS 5.5 tune" and "AOS 5 tune", both could arguably match the name "AOS 5 v5". I guess "AOS 5" is the right one.
I tried this on my AOS 5 V2 with AOS Supernova motors today. There was still a bit of trilling with the master multiplier at 1. I've lowered it to 0.95 and we will see how it goes.
I'm gonna to test it today on my AOS 5 v5 + Supernova motors. Until yesterday (before installing this) I solved the problem limiting the throttle to 80%. Now I've set it back to 100% to see the effect, if I'll notice thrilling, I'll lower the value again
Yes, they may need different amounts of master multiplier so follow the standard procedure to gradually raise master until you find the max level without oscillations.
hi chris, i update my UL7 with your 4.5 BF preset, i also switch PWM freq from 48 to 24kHz on my ESCs. Now when i arm, +20amps drawn at idle (pitch oscillation seen on the blackbox). As soon as i take off, normal amps draw, like 7. Do you what know happens to my quad ? first time i have seen this..
@ChrisRosser that's amazing!! thanks very much, sir!! I'm running one of the new Neutron RC AT32/AM32 w/BMI270, and I'm finding it to be a challenge to eliminate all oscillations. I'm very close, but still getting an unreasonable amount of propwash. I think it's a filter issue. Excited to try this out, and see how your settings differ from where I am. Much appreciated, Chris. 🙏🫡
Hi, thanks for the video. New subscriber :-) I am building a 2 inch 2s so I just loaded your 2 to 4 inch preset and that’s it? Or is there other presets I want to add to that? Thank you go fly.
Nooooooo …. I just did all this manually . . . Filter tuning. On the betafpv meteor 85. By feels. But thanks! Looking to sign up. Just procrastinating.
Found the presets before finding this video, the 3.5" one was a huge help for me since I'm unable to install MATLAB atm (apparently it doesn't like dashes in my username). I burnt up a component on my last FC so I had to swap it out aaaaand... yeah.
In a few days my aos supernova should arive i hope i dont mess the pids up with my fool mind Do you have some ideas for me? Mamba f722 app mk4 Mamba f55 4in1 esc Youre aos motors Crossfire nano. A02vtx 800mw with phoenix runcam v2 cam And the frame is a geprc mark4 Evt sombody has some ideas Btw i run 150c 6s batterys
You keep saying "drone" in place of "frame". Regardless of that, presets are never a good idea for tuning. For rc link? Sure. Never tuning or filtering. You're gonna burn up a lot of people's shit, just wait.
Awwww man... I was so excited to get home from work and download these. I've been working on a tune for the AOS T3 for a week and a half and I'm stuck with a lot of propwash and oscillations. I guess it's back to the struggle...🥲 Any chance of a 3s 3" toothpick tune and filters?? TIA.. 🙏
Im getting fly aways with a clean 2.5inch 3s build. I managed to make it flyable with an example on another similar build, but it feels extremely wobbly almost like its completely off rails. Any sugguestions?
UPDATE: These presets are now merged into the main repo so no need to add a new source! I'll leave the steps in the video for now.
Thanks
YEAH! These presets are a HUGE reason to purchase AOS products. Chris, your expertise canned into presets is incredibly valuable. I’ve been writing PID code, tweaking PID values, etc. since 2009 and I’m sick of it! I’m retired from aviation and just want to fly… AOS Rocks! And so do their Hoodies! Buy one today!
Lol
After hours of tuning my 5 v5 I found these presets and tried them out - I must admit, I kinda failed with my tuning 😂 Thank you so much for your work! Absolutely smooth with Xing2‘s 1755kv and 6s 1300mAh‘s!
Thanks, Chris! 😊
Stay safe there with your family! 🖖😊
Thank you Chris. Updated yesterday. Haven't flown yet but hopefully today. Great frames, great work.
Fried a motor within 5 seconds using your 5" preset. Brand new drone broooooooo!!!!
Quak
@@kimpassey5618was it an aos frame
I'm getting a mixer mode problem. It needs 4 motor resources but current firmware provides 0.
Need to define a custom mmix before changing mixer mode.
Check configuration and add the required motor resources.
I'm not sure what to do here?
Man, thanks! Built a BFPV Meteor 75 Pro Walksnail a year ago and it has always had a slight wobble only noticeable when hovering no matter what I did. Updated to 4.5.0, still wobbled. Applied your standard 1S whoop tune, fixed!
Did enyone get some kind of error message aufter applying a Preset
Just ordered an AOS UL10 frame. Going to build it up with gear I already have on hand : Goku F722 stack w/ 50A ESC, BH 3115 1050kv motors (on 5S), Walksnail video.
Doesn't look like there are any presets for this frame. guess I can use the UL7 settings as a starting point.
Any presets to take 2024 Mobula 6 HDZ Frestyle for indoors flying beginner learning Acro? Was thinking to scale throttle to 65%, mid to 0% with 0.5 expo; and do 50, 450 and 0.5 expo on(pitch, roll and yaw).
Chris, I’m just about to build with the components below, will the presets be okay with this? AOS 5 V5, Speedybee F405 V4 60amp esc, DJI 03, Supanova 2207 1950, ELRS. Any help would be great.
Chris, I’m pretty distraught and don’t know what happened. I have the AOS 5v5 frame with the supernova motors and not 10 sec into my first flight it dropped out of the sky and I found that two motors were burnt up. I used your tune in this video. This is my first build and it’s left me pretty low. Any thoughts? I would SO appreciate your help.
I just finished the same build, I noticed the motors sounded like they were “grinding” and then checked and they were hot. I’m thinking the supernovas need a master multiplier of less than 1.0 as when I switched back to the default beta flight tune, the motors sounded normal again. Hopefully Chris can weigh in on this.
I'm looking at which preset should match for my "AOS 5 v5" and the preset names and descriptions confuse me a little. There is "AOS 5.5 tune" and "AOS 5 tune", both could arguably match the name "AOS 5 v5". I guess "AOS 5" is the right one.
Is there presets/rates for new angle mode for whoops - i remember you have video about that?
Hi Chris, is it possible to test your preset for a non aos frame? I want to try this with my 3,5 inch quad weights 300g with 6s 450mah lipo.
I tried this on my AOS 5 V2 with AOS Supernova motors today. There was still a bit of trilling with the master multiplier at 1. I've lowered it to 0.95 and we will see how it goes.
I'm gonna to test it today on my AOS 5 v5 + Supernova motors.
Until yesterday (before installing this) I solved the problem limiting the throttle to 80%.
Now I've set it back to 100% to see the effect, if I'll notice thrilling, I'll lower the value again
Also consider adjusting TPA if trilling is only occuring at high throttle 👍
Are the tune and filter settings the same for all AOS 5 frames? I have both the V2 and the V5. Thanks Chris.
Yes, they may need different amounts of master multiplier so follow the standard procedure to gradually raise master until you find the max level without oscillations.
Will the ul5X presets be aviable?
TINY WHOOP : Hi Chriss From Quebec, Canada ⛄️❄️ For whoops do you have presets ??
hi chris, i update my UL7 with your 4.5 BF preset, i also switch PWM freq from 48 to 24kHz on my ESCs. Now when i arm, +20amps drawn at idle (pitch oscillation seen on the blackbox). As soon as i take off, normal amps draw, like 7. Do you what know happens to my quad ? first time i have seen this..
Hi Chris.
I can't find the AOS 3 toothpick tune?.
Same. A bit disappointing..
Added to aos-rc and PR live for inclusion into the main repo. Thanks for reminding me!
@ChrisRosser that's amazing!! thanks very much, sir!!
I'm running one of the new Neutron RC AT32/AM32 w/BMI270, and I'm finding it to be a challenge to eliminate all oscillations. I'm very close, but still getting an unreasonable amount of propwash. I think it's a filter issue.
Excited to try this out, and see how your settings differ from where I am.
Much appreciated,
Chris. 🙏🫡
Very nice! PID tuning is something I'm more or less afraid of.
Will these also work for tiny whoops with 20K-30K+ KV motors?
Try Ayykayy's preset, gary kents justice tune, or the karate tune. Ayykay's works great for me on high kv..
@@willpowerfpv3246 Sweet! Thanks a ton! :)
I got bad flightperformance with AOS7 on INAV. Are there any suggestsions for PIDs in INAV as well?
Hi, thanks for the video. New subscriber :-) I am building a 2 inch 2s so I just loaded your 2 to 4 inch preset and that’s it? Or is there other presets I want to add to that? Thank you go fly.
Great 3.5" ❤ tune for my AOS - RC v5. Flies Amazimg with 2004 flash 2900kv motors! Thanks geezer!🫡
Nooooooo …. I just did all this manually . . . Filter tuning. On the betafpv meteor 85. By feels. But thanks! Looking to sign up. Just procrastinating.
Hi I am fairly new and faily old bought Geprc 30 what's a good preset sorry I am totally a noob. Thank you in advance.
Found the presets before finding this video, the 3.5" one was a huge help for me since I'm unable to install MATLAB atm (apparently it doesn't like dashes in my username). I burnt up a component on my last FC so I had to swap it out aaaaand... yeah.
Applicable to just aos frames or any?
It's literally the first part of the title of the video
Yes I needed this!
Its only for BF 4.5?
I was looking the other day but didnt see one specifically for the AOS UL5X, is there a preset for UL5X or one you recommend?
Yes you should use the UL5 preset 👍
Hay Chris, I've bought an AOS Falcon 7, will your 7" AOS preset be ok with it?
Yes absolutely!
In a few days my aos supernova should arive i hope i dont mess the pids up with my fool mind
Do you have some ideas for me?
Mamba f722 app mk4
Mamba f55 4in1 esc
Youre aos motors
Crossfire nano. A02vtx 800mw with phoenix runcam v2 cam
And the frame is a geprc mark4
Evt sombody has some ideas
Btw i run 150c 6s batterys
Helped a lot, thank you.
Tride yout UAV 5" w/gopro tune on a Five33 Footy and got a fly away. 😅 Gonna trie the AOS7 tune and filters on an Evo. Thanks! :D
I don't think I have a UAV 5" w/gopro tune... all my tunes start with AOS.
@@ChrisRosser you are correct! I mixed you and uav tech. Sorry. 😅 Anyways, tried the aos7 tune on evo. Flies well. Ramped mm up to 1.5 👍
Thank you so much!!
Liar! it was 3 clicks!
Inexcusable click bait! 🤣
How the hell do you apply a preset to a FRAME? Lol wtf
Its not the same a 5" frame or a 2.5" frame
Hey man you need to take a seat
He sells also BNFs. Pretty good support to provide tunings also...
You keep saying "drone" in place of "frame". Regardless of that, presets are never a good idea for tuning. For rc link? Sure. Never tuning or filtering.
You're gonna burn up a lot of people's shit, just wait.
He sells also BNFs. Pretty good support to provide tunings also...
Awwww man... I was so excited to get home from work and download these. I've been working on a tune for the AOS T3 for a week and a half and I'm stuck with a lot of propwash and oscillations. I guess it's back to the struggle...🥲
Any chance of a 3s 3" toothpick tune and filters?? TIA.. 🙏
Yep I'll do one for the T3 and add it!
kiss ultra = defaults. done.
This is the way
Kiss Ultra is garbage 😂
Unfortunately not for every buiild. I love ultra, but it's not jiving with my 5.5" on 25mm motors...
Im getting fly aways with a clean 2.5inch 3s build. I managed to make it flyable with an example on another similar build, but it feels extremely wobbly almost like its completely off rails. Any sugguestions?