First off Thank you so much for your video Also, what was the last black wire you grounded to the casing of the blend pot, You already grounded the preamp to the casing of the blend pot, so where was the last black wire coming from?
Got a Bass from someone recently. The center position on the blend pot is much lounder than the other two positions. I'm assuming something is wired wrong or bad pot?
HI thanks for the video, I did this in a bass that had 2 volumens, is an active bass with circuit, but I did everthing ok and it sounds ok, but the problem is that blend is almost unnoticiable, when I move it to Bridge pickup its like it changes all the way and I don't have a smooth changing of pickups while rotating the potentiometer... why is that?? thanks for the video It helped me a lot.
@@tixcustomsph yes the same one that you have... The only thing is that mine the output goes to the volume pot and the output in the volume goes to the preamp... I read that there is another pot to use a Delano C250k special for this... But I don't know
in a lefty bass, rule of thumb is no more. actually you can swap up/down on a righty too, but it makes more sense on a lefty. cw is neck, ccw is bridge. I did it on my basses, ungrounded blend cutting the traces for no load.
Ok, I do not play bass but am building my first bass for my father. I have Seymour Duncan Quarter Pound pickups. I bought two volume pots and a tone pot. But I am planning to replace to tone pot with blend pot. So does it make sense to have two volume and this blend pot? Do you have any instructions on doing that?
@@tixcustomsph if I have a bass guitar with a passive pickup, and I want to install a potentiometer to split the sound of the neck and bridge. So should I use the same potentiometer as in the video or another 6 pin potentiometer?
![Jazz Bass Rewiring from Scratch [with subtitle]](http://i.ytimg.com/vi/Dm58i92au6A/mqdefault.jpg)
My soldering skills are greatly improved after watching you do it in your videos. Thanks!
❤️❤️❤️
Nice and clean, thank's a lot man !!
First off
Thank you so much for your video
Also, what was the last black wire you grounded to the casing of the blend pot,
You already grounded the preamp to the casing of the blend pot, so where was the last black wire coming from?
Yun may bagong tech sa wiring si sir Salamat po sa tips
Salamat din sir!
My blent pot has no sound when in the middle position. Only when on bridge or neck. Did i do something wrong?
If it is MN type, just reverse the hot and ground wires 👍
Pwede ba gamitin to sa acoutic guitar, to mix active magnetic pick up and piezo pick up with preamp?
Yes pwede rin sya.
Are you only using the hot leads of the pickups? Hard to tell in video
Ground leads are soldered to the case of the pot.
Thanks this video helped me a bunch.
Got a Bass from someone recently. The center position on the blend pot is much lounder than the other two positions. I'm assuming something is wired wrong or bad pot?
It could be a bad pot. Is it an MN type blend pot?
HI thanks for the video, I did this in a bass that had 2 volumens, is an active bass with circuit, but I did everthing ok and it sounds ok, but the problem is that blend is almost unnoticiable, when I move it to Bridge pickup its like it changes all the way and I don't have a smooth changing of pickups while rotating the potentiometer... why is that?? thanks for the video It helped me a lot.
Hi did you use the MN type blend pot?
@@tixcustomsph yes the same one that you have... The only thing is that mine the output goes to the volume pot and the output in the volume goes to the preamp... I read that there is another pot to use a Delano C250k special for this... But I don't know
in a lefty bass, rule of thumb is no more. actually you can swap up/down on a righty too, but it makes more sense on a lefty. cw is neck, ccw is bridge. I did it on my basses, ungrounded blend cutting the traces for no load.
Yes we have to reverse 1s and 3s if we are gonna wire a lefty bass. With regards to blend, only the upper and lower.
Ok, I do not play bass but am building my first bass for my father. I have Seymour Duncan Quarter Pound pickups. I bought two volume pots and a tone pot. But I am planning to replace to tone pot with blend pot. So does it make sense to have two volume and this blend pot? Do you have any instructions on doing that?
There's no need to have 2 volume pots if using a blend pot. Just master volume, blend and tone. Please check the Seymour Duncan website for diagrams.
@@tixcustomsph Thanks, I found the instructions. Going to change out tonight.
Goodluck!
Kalau memakai pickup pasif apakah harus memakai potensio mn250/500k? Atau bisa pakai potensio kaki 6 yg lainnya?
Sorry my friend but I can't understand what you are trying to say.
@@tixcustomsph if I have a bass guitar with a passive pickup, and I want to install a potentiometer to split the sound of the neck and bridge. So should I use the same potentiometer as in the video or another 6 pin potentiometer?
@@tixcustomsph Sorry my English is not good. I think it's available on TH-cam to translate in the comments column
haloo...how to connec pu Bartolini mk1 to blend spot?
Just the same as I did in the vid.
Excellent course..
Thanks!
❤
Thanks!