Nice contraction to increase the size of a wrench, but bad craftsmanship. n_n next time get a pipe bang it until is flat and the wrench snuggles in... if that is not enough leaver you can fit that pipe inside a longer one and you save your self all the grinding
This video is about as bad as the one where the guy says you shouldn't haul with a lifted truck. Definitely unauthorized mechanic, and I've seen quite a few, surprisingly this is the worst.
Thanks for your criticism, but to be constructive you should explain in detail what you didn't like. There are many incapable who like to talk, because that's the only thing they know how to do(however with poor results).
Why not use a breaker bar and socket or even a crows foot or do what I did and use the milwaukee 1/2 drive 18v electric impact with 1400 ft pounds of take off torque
There was not enough room to use directly a breaker bar. Then I had used a swivel socket like extension with pneumatic impact wrench (1750 Nm) and flame. The problem arose from the fact that some genius had replaced a bolt by tightening it with something heavy, jamming it.
True, it drained the torque, it was not supposed to work with an impact wrench. Besides, it shattered. I didn't have a swivel dedicated to the impact tools at the time, so I decided to try sacrificing what I had. Even if it worked in the end, I absolutely advise against it.
![CAMPปลิ้น | EP.82[1/2] แก๊ง 3 สาวเพื่อนซี้บุก CAMPปลิ้นครั้งนี้ห้ามเสียอาการ](http://i.ytimg.com/vi/_6WUjXHe1TM/mqdefault.jpg)
if you use two wrenches connected, you can get more leverage without making something special
Broooo I was in 😭 the struggle was real 🤣 , you need 🔥, I was like put a Milwaukee on low and let it work.
Mr bean “the mechanic “ lol
Nice job
😂
Very funny and helpful. No music, just the real sounds of mechanic work. Im impressed with the common sense I saw in this video. Thumbs up. 👍👍👍
Thank you very much. Really appreciated.
Funny ass video. Thank...... p.s.
Very helpful video. Thank you U.T.M.
Thanks I'm glad it was useful to you
Wrench hammer method
Nice contraction to increase the size of a wrench, but bad craftsmanship. n_n next time get a pipe bang it until is flat and the wrench snuggles in... if that is not enough leaver you can fit that pipe inside a longer one and you save your self all the grinding
Using MAP gas will work much better. Also after you heat it up glowing, quench it with water, it will crack all the grud and rust.
This video is about as bad as the one where the guy says you shouldn't haul with a lifted truck. Definitely unauthorized mechanic, and I've seen quite a few, surprisingly this is the worst.
Thanks for your criticism, but to be constructive you should explain in detail what you didn't like.
There are many incapable who like to talk, because that's the only thing they know how to do(however with poor results).
Why not use a breaker bar and socket or even a crows foot or do what I did and use the milwaukee 1/2 drive 18v electric impact with 1400 ft pounds of take off torque
There was not enough room to use directly a breaker bar. Then I had used a swivel socket like extension with pneumatic impact wrench (1750 Nm) and flame. The problem arose from the fact that some genius had replaced a bolt by tightening it with something heavy, jamming it.
Ahh man! all you needed is a short piece of pipe to make wrench extension!
"Give me a lever and I'll lift the world" Ἀρχιμήδης
Really need to invest in a swivel set of sockets, the swivel you are using takes away torque from the impact wrench.
True, it drained the torque, it was not supposed to work with an impact wrench. Besides, it shattered. I didn't have a swivel dedicated to the impact tools at the time, so I decided to try sacrificing what I had. Even if it worked in the end, I absolutely advise against it.
Don't you just love impact wrenches 😃
I'm learning to love them