Beautiful result Uri. One big thing which may be tripping you up is that you seem to be scoring the glass multiple times. That's generally a big no-no when it comes to glass cutting, and tends to lead to fragments being broken off rather than the crack propagating along the scoreline. Score once, snap once. Glass cutting is an art indeed!
Yes, I should have looked at videos before I attempted to do it myself. They make it look dk easy😅. Perhaps a thiner plate would have help aswell. I don't think I have the neck for glass work😂
@@urituchmanpigeon oh tell me about it, I gave it up long ago. Last time I tried was to make a custom rear view mirror for my van I ended up belt sanding it to shape 😄
Thanks, I appreciate it! I'm really not trying to be extra modest or anything, but when I see masters work online I can't help but feel a bit amateurish, which is totally fine by me.
Cutting wheels are tungsten carbide: - don't go over a cut twice, it makes the wheel dull - each wheel is good for 3 - 5 cuts, then throw it away; it is dull - cutting oil helps, but the wrong kind makes the wheel dull - looking at the wheel makes it dull
couple tipps for cutting glass: 1: never cut twice over the same crack, it fucks up your cutting wheel. The one you used is probably pretty scuffed already. 2: tapping the cut with a hammer is a good way to deepen the cut. LIGHT hammer taps from the bottom (the uncut side) until the sound of the tapping changes 3: you can put some cutting oil on the cutter, it will make it last longer. 4: you can put something like terpentine where you will cut, it also enhances cutting power Beautiful piece! Seeing these kind of videos makes me want to get into crafting again. Also top notch editing haha
When I have to cut a glass bottle, I score the glass once and then run boiling water over the line, immediately followed by cold water. I alternate between boiling and cold water a few times and usually that will break the glass perfectly along the line. I wonder if that also works for sheet glass.
It'd definitely work! But not really necessary. 'Running' the line is pretty easy with gentle pressure either from running pliers or pressing the glass into a foam or soft surface will work, or very traditionally, just tapping. Bottles are hard mode@@eelcogg !
I've been working with glass for several years now, and i have some tips. 1. You should never cut twice. One firm but smooth cut only, or it won't break properly. 2. You have to use a cutting lubricant (kerosene is fine). This is applied to the glass where you will make the cut. 3. When trying to break out a circle, you must do it from the back. Support the top (cut side) of the glass, and push directly on the bottom (uncut side) of the cut. You will see it break a little, and you just "run" this break all the way around. After that, you need to cut a relief on each side (where the circle is closest to the edge) and take the trim (scrap glass) off in 4 separate pieces. This is because you cannot remove a circle from a hole that's exactly the same size as the circle.
"… engraving is inevitable so that's going to happen …" Thank you for reminding me that ornamentation does not have to be called for. I just replaced an 8lb (~4kg) sledgehammer handle and took the opportunity to mill flats on the side so I could engrave "Katy's Hammer" on one side and "Whosoever holds this hammer; should she be worthy, shall possess the power too… sunder timber" on the other. With flourishes of course, I am not an animal.
The glass is tapped exactly along the glass cutter's line until a crack appears under this line. and I highly recommend changing the roller tip to corundum or diamond, the rollers do not cut well.
Nope. Diamond only scratches the glass. The steel wheel creates a line of weakness in the glass and the fracture follows this line. Try scratchig a piece of glass and you will find that the fracture line does not follow the scratch.
@@tednelson5277 I think you may be confused, as everything you said is wrong. First off all that "weakness" you reference is the scratch. All glass cutters - steel, carbide, and diamond - score or scratch the glass in order to encourage the breakage to follow that line. It does not always follow the line, but that is due to the natural "grain" of the glass, not any artificial weakness caused by the steel cutter. Why would the weakness created by the wheel be off the path of the scratch anyways?
@@tednelson5277 i was try it a lot of time. line of weakness is pretty exist for scratch by diamond too, because fact of surface damage is enough for it with a little tapping. wheel instead require a lot of pressing for desribed result and often crack the glass if you press too strong. wheeel is advertised as a try to awoid tapping at all but it is not a good solution - just a cheap production. Additonally - wheel is awful for a small radius curves.
@@anatoliyzhestov3915 Sorry, but you are wrong. If the glass breaks wheel you use a wheel, you are no supporting the glass. Diamond only scratches. Ask any professional stained glass cutter.
@@tednelson5277 ask any professional you mention what he does and he will tell you - I draw hundreds of straight lines a day. In these conditions, a roller that can be changed frequently and is inexpensive is an advantage. But among those who do small, precise work with small radii and want to get a very clean and precise cut, the number of diamond glass cutters may a lot surprise you.
This is so very very very beautiful, and as a glassworker I appreciate it so much!!!!!! Watching you try to cut glass without the correct breaking tools, and cutting twice though... 😛
Cutting glass has been part of my profession for 24 years. It likes to fracture in straight lines, and in paths of least resistance. For that reason, scoring multiple times tends to cause jagged edges and additional fractures. A slow, deliberate and firm score works best. What can help with scoring is dabbing the cutter wheel on a sponge soaked in wd40. Idk why it helps, but it does. And when cutting circles/ovals score additional tangents to the circle so it looks like a whirlpool, making sure that there's about 5mm between the circle and the start of the tangent score. Tap the unsecured side of the glass, tracing the scoring. Tap the circular score first and gently so the scores become cracks. It will be visible when the scores crack. Once your circle is set, tap the tangent scores. The cracks should break to meet in the same direction on their own, and you can remove the loose pieces as they fall away. Thanks for uploading. I always enjoy your content❤
_"Idk why it helps, but it does"_ - it lubricates the wheel, so it rolls easier on it's axis, and then WD-40/ kerosene/ glass cutting oil (yes, there is such oil) seeps into the score (which is a miniscule crack in the glass) - i.e. capillary force "push" it into the glass, and it either reduces the attraction between glass molecules (van der Waals force?) or in some other fashion facilitates the propagation of the initial crack (which is caused by "scoring", and lies underneath it) - or both (can't remember now exactly). Also, "wiping off" the glass where you intend to make the score (just swipe yer finger across the glass) removes whatever dust have accumulated there and that helps to prolong the life of the wheel... or so I was told when I started my glazing job about twenty years before you did ;-)
@@davidhoward496 Also, I forgot to say, but then you might know it very well yourself, so all the following is probably "teaching a priest how to say Lord's Prayer" but I'll write it anyway ;-) So, high quality glass cutters have single wheel pivoting heads (so the head always stays 100% parallel to the direction of the cutting movement/ travel and/or the straight edge) and they have hollow brass handles which double as containers for cutting oil (which seeps down to the wheel lubricating it and wetting the score). Google for "silberschnitt oil glass cutter" (for example). For regular "dry" cutters there are so-called oiling stands available, in which you place a small piece of cotton cloth or felt (a piece of a paper towel would also do) soaked in cutting oil - when you don't use the cutter you place it in this stand, and whenever you want to make a score the cutting head (and the wheel) is already oiled. Also, I'm no longer doing any glazing (it's been "quite a while" since I quit it) - apart from occasional "could you help me, please?" for friends and such, and at any rate virtually all windows now use IGUs (aka double glazing units). Cheers!
trying new tools/workflow is always intimidating. I encourage you not to give up trying to incorporate those new processes. As much as I love seeing your brass/woodwork, It is refreshing to see you trying out new things and I hope you continue to do so.
Anyone with a hobby should be able to relate to the “spending millions of hours making some pieces of garbage!” So spot on. Thank you for this great video!
I remember while taking a class in school for stain glass, the trick was to make one, hard, continuous cut, not several cuts. I recall needing quite a bit of pressure while using the cutter.
It is awesome how much this man has evoled, and grown. Even his social skills talking to viewers are noticeably better. I am a fan of this channel definitely!
You make me happy, Mr Tuchman. I admire your willingness to try new things, fail, and learn. I think you are the most amusing and engaging engraver on the internet, so you might not be the master but you are very watchable and that is why you get my attention. Thank you.
This "Golden Cut" brand reminds me of that Silberschnitt brand (German for "silver cut"), which was, if I'm not mistaken, a DDR "derivative" (knock-off) of West Germany Hartmetall glass cutters. EDIT - just checked it, seems like "it's the other way round" - i.e. Silberschnitt was West Germany brand and Hartmetall was DDR "derivative". And the quality of the wheel makes a "day and night difference" when it comes to glass cutting - so if you want to cut glass without any trouble get the best ones you can afford (within reasonable range, that is). This "home improvement/ hobbyist" brand is good just for that. Shops selling glazing tools and supplies sell cutting wheels "stand-alone" fashion, and there are plenty of sellers of these on all sort of internet selling platforms too. It's really worth getting high quality cutting wheels. Then there are different cutting edge geometries for various thickness of glass (thick glass requires different angle grind of the cutting edge, more obtuse one AFAIR) and then there some special "glasses" (like X-ray shielding glass, which is made mostly of melted lead oxides, or that "glass-ceramic" thingy for fireplaces, like Robax) which require dedicated wheels as well. Also, when cutting thick glass the force needed to score it is greater (thus different handles in such cutters) AND special pliers to run the crack, but when you use good quality new wheel the force applied should be "just enough" to score it - when you see tiny strands of glass flaking off by itself from the score (right after you made it) it means the force was too strong, and it will not only shorten the lifetime of the wheel (will blunt it, to put it bluntly... ;-) but this may actually worsen the quality of the cut. And while light "tapping" the glass on the opposite side (underneath the score) with a hard object does "open up" the crack, the edges of it (where you tapped it) will be wavy - for regular glass thickness (2 - 6 mm) simple breaking it with your hands should do (if the score is right), preferably with "pulling apart" motion added. Place the scored pane on a table so the score is still on the table but very close to the edge (5 mm or less) of it, hold it down with your left hand and "break off" that part outside of the table by pushing it with your other hand. Or when the pane is too big for it, just lift it a little and place some soft (but firm) object under the score at the edge of the pane (a wooden handle of a regular glass cutter, or a pencil would do) and gently press the pane with your both hands placed 5 to 10 cm away from the score. When the off-cut part is too narrow for any of the aforementioned methods use special pliers - regular workshop universal pliers are not suitable for this task. In a pinch they "will do", but very poorly - unless you have one of these special "parallel jaws" pliers. And at any rate the minimum off-cut width should be twice the thickness of the pane, or you may end up with a bit of a struggle and a rather jagged edge of the glass. And, oh, BTW - hardened steel DOES score glass, but it's rather special kind of steel, with a lot of cementite in it, and VERY hardened ;-) Looks like nowadays they make mostly carbide or PCD wheels though. Check the Bohle (Bohle AG) online store - bohle-dot-com.
_Of course_ you made the fanciest glass cutter! You're Uri Tuchman-it wouldn't matter what thing you made, it could not possibly be less than the fanciest example of that thing in existence!
Ok, fantástico trabajó maestro, un proyecto muyyyy original y peculiar, gracias por compartirlo con los pobres mortales, Uri un cordial saludo y por supuesto un merecido like desde Narón (Galicia)👍🤓😜
I used to be a “machine operator” for an aerospace contractor. Which is sort of like being a machinist without the in-depth knowledge… Man all I can say is you a fantastic craftsman! You make it look easy but that takes some real skill! Keep up the great work.
While everyone is trying to explain how to cut glass, I just want to say that little Derringer is BadASS! Beautiful engraving, nice handle, clever hinge and the case is perfect! Good job. If you come to the Maker Faire in California, I'll see you there. Bicycle rodeo!
The way glass cutters work is "stress concentration" which just means that they make a very sharp but shallow gash in the surface which should make the glass split right there. The reason this works is because what breaks a material isn't just the amount of force but the force divided by the area where the force is applied which is called stress. So, if you make that area very small, like at the tip of a very sharp scratch, the stress becomes huge. So, it's actually better to make a single fine scratch with the glass cutter rather than going over the same line may times because while you're making the gouge deeper, you're also making it wider and thus duller
Uri, I think next big project will be investment casting. It will allow to have smallest details. You can nickel plate locally with a wet sponge. If your steel quenched in water then it is W1. O1 is quenching in oil. I had also negative experience with glass cutting. When you scratch the glas you create a weak zone. Doing it multiple times does not help and opposite. When you start applying stress it does not cocentrate if you have several scratches. Perfect video. As always!
I've tried casting tin with that same high temp silicone, casting a 3D printed coin. I think the problem we both ran into is that the tin cools too quickly. The mold needs to be a material that can be heated (sand, ceramic, etc) so the tin cools slowly and can get into all the nooks and crannies. In my case all the holes and imperfections made the coins look like old, corroded shipwreck treasure so it worked out okay.
Watching screws or bolts get made on a lathe feels insane every time I see it. Watching that big log of metal getting cut down so much until there's a tiny screw
Haha don't change one bit Uri! Loving the music at the 12:00 mark, very funny. Also have you thought of using a toggle clamp to hold down your work piece when drilling on the drill press? They are very cheap and work super well!
@@____________________K i think it's "Lupus Nocte - Getting Lost" not sure tho, just looked it up with: i'm getting lost from what i heared from the lyrics
Hi Uri, after spotting you at last years show and missing the opportunity to say hello I will pop over this time and have a natter !!! Great work mate, fun as always !!
I have a tip for getting the curved cuts, and cool enough, it's a secret feature you added to the cutter and didn't know it! Turn that sucker around and hit the glass with the butt of the gun multiple times along the scores. Not so hard to shatter it, but firm enough to make it vibrate. It causes micro fractures along the score lines, and eventually the microfractures will all connect and the glass will just pop apart where you scored it. On a standard glass cutter, that's why it will often have a large ball on the handle end, but the butt of the gun would likely work really well for that! Also, your work is really awesome and I love seeing your ideas to fix problems; like the offset screw that covers the pin.
As a stained glass art maker, my advice is this: Glass cutting oil will improve performance and reduce chipping...or at least reduce the distance the chips fly, therefore being safer for your eyes. Also, please wear safety glasses when glass cutting! The oil reduces the wear on the cutting wheel because of the reduced friction.
Thank You Uri Tuchman... GREAT ONE !!!!!!!! BEAUTIFUL AND FUN TO WATCH!!!!! (Q- HOW DO I GET THAT LAST LITTLE BIT OF TOOTHPAST OUT OF THE USED UP TOOTHPAST TUBE????????? ) ... TM
I second the comments saying that the casting molds need some "spouts". Places where the extra metal can go, chasing air out. But for such fine detail you probably need to use an injection mold. I tried making flat molds but the result needs a lot of additional work to remove excess metal on the back and possible re-work details. Having said that, the result is amazing, it looks so cool! I hope the client sends you photos of it in use
Beautiful result Uri. One big thing which may be tripping you up is that you seem to be scoring the glass multiple times. That's generally a big no-no when it comes to glass cutting, and tends to lead to fragments being broken off rather than the crack propagating along the scoreline. Score once, snap once. Glass cutting is an art indeed!
Hey man, I just wanted to say I miss your videos. I've been watching since the kant twist clamp days.
He should try making an all metal version of Rock’Em Sock’Em Robots.
Yes, I should have looked at videos before I attempted to do it myself. They make it look dk easy😅. Perhaps a thiner plate would have help aswell.
I don't think I have the neck for glass work😂
@@urituchmanpigeon oh tell me about it, I gave it up long ago. Last time I tried was to make a custom rear view mirror for my van I ended up belt sanding it to shape 😄
A drop of oil or kerosene apples where you start the cut apparently also makes it easier to achieve a continuous cut line.
Cutting edge tool.
Thank you! In the Next project I'm making shears that'll be cutting hedge... Sorry
agreed
And the wrench he used wasn't bad either.
Was that a pun?
@@FellowInconsistent yeah well @handtoolrescue is a pretty sharp guy.
This channel is what I imagine an Artisan from the Renaissance would do, if he had access to TH-cam.
"I'm not a master engraver." *proceeds to prove otherwise
Thanks, I appreciate it! I'm really not trying to be extra modest or anything, but when I see masters work online I can't help but feel a bit amateurish, which is totally fine by me.
Dude, you're epic, don't let anyone including your inner self tell you otherwise. My 2c.
Daddy is always pulling our leg :-) Thanks for the great video & new ideast!
@@urituchmanpigeon remember, its still 2 cakes
Imposter syndrome
Cutting wheels are tungsten carbide:
- don't go over a cut twice, it makes the wheel dull
- each wheel is good for 3 - 5 cuts, then throw it away; it is dull
- cutting oil helps, but the wrong kind makes the wheel dull
- looking at the wheel makes it dull
Not using the wheel makes it dull
Don't store it in a humid place, that makes it dull. Do not store it in a dry place, that makes it dull.
Don't look at the wheel while using it, that makes it dull
existing near the wheel makes it dull
The wheel is dull. It just came that way, sorry. Better get another one, quick.
couple tipps for cutting glass:
1: never cut twice over the same crack, it fucks up your cutting wheel. The one you used is probably pretty scuffed already.
2: tapping the cut with a hammer is a good way to deepen the cut. LIGHT hammer taps from the bottom (the uncut side) until the sound of the tapping changes
3: you can put some cutting oil on the cutter, it will make it last longer.
4: you can put something like terpentine where you will cut, it also enhances cutting power
Beautiful piece! Seeing these kind of videos makes me want to get into crafting again. Also top notch editing haha
also keep the pressure consistent. (no gaps)
When I have to cut a glass bottle, I score the glass once and then run boiling water over the line, immediately followed by cold water. I alternate between boiling and cold water a few times and usually that will break the glass perfectly along the line. I wonder if that also works for sheet glass.
It'd definitely work! But not really necessary. 'Running' the line is pretty easy with gentle pressure either from running pliers or pressing the glass into a foam or soft surface will work, or very traditionally, just tapping. Bottles are hard mode@@eelcogg !
The only other thing I would add would be some proper glass Nippers
also have a few whiskies...
I've been working with glass for several years now, and i have some tips.
1. You should never cut twice. One firm but smooth cut only, or it won't break properly.
2. You have to use a cutting lubricant (kerosene is fine). This is applied to the glass where you will make the cut.
3. When trying to break out a circle, you must do it from the back. Support the top (cut side) of the glass, and push directly on the bottom (uncut side) of the cut. You will see it break a little, and you just "run" this break all the way around. After that, you need to cut a relief on each side (where the circle is closest to the edge) and take the trim (scrap glass) off in 4 separate pieces. This is because you cannot remove a circle from a hole that's exactly the same size as the circle.
Your video editing has really improved. I love the Uri inserts, singing , in the lathe section.
It's been a fun journey watching him grow over the last several years.
"… engraving is inevitable so that's going to happen …" Thank you for reminding me that ornamentation does not have to be called for. I just replaced an 8lb (~4kg) sledgehammer handle and took the opportunity to mill flats on the side so I could engrave "Katy's Hammer" on one side and "Whosoever holds this hammer; should she be worthy, shall possess the power too… sunder timber" on the other. With flourishes of course, I am not an animal.
Ope, wrong 'to', may need to redo that, somehow
*"power to"
Too means "as well" or "also"
"I need to take a shit!"
"Me too!"
Savvy?
There's no such thing as a bad video from Uri. Each video is an adventure. A pleasing journey of discovery. Always entertaining. Thank you sir!
there are many creative people here on TH-cam but i think what is special about Uri is his ability to get his ideas into realty.
Fabulous!
Thank you!
Outstanding, Uri!! Beautiful work.
The glass case, almost break the glass in case of an emergency - spot on.
The glass is tapped exactly along the glass cutter's line until a crack appears under this line. and I highly recommend changing the roller tip to corundum or diamond, the rollers do not cut well.
Nope. Diamond only scratches the glass. The steel wheel creates a line of weakness in the glass and the fracture follows this line. Try scratchig a piece of glass and you will find that the fracture line does not follow the scratch.
@@tednelson5277 I think you may be confused, as everything you said is wrong. First off all that "weakness" you reference is the scratch. All glass cutters - steel, carbide, and diamond - score or scratch the glass in order to encourage the breakage to follow that line.
It does not always follow the line, but that is due to the natural "grain" of the glass, not any artificial weakness caused by the steel cutter. Why would the weakness created by the wheel be off the path of the scratch anyways?
@@tednelson5277 i was try it a lot of time. line of weakness is pretty exist for scratch by diamond too, because fact of surface damage is enough for it with a little tapping. wheel instead require a lot of pressing for desribed result and often crack the glass if you press too strong. wheeel is advertised as a try to awoid tapping at all but it is not a good solution - just a cheap production. Additonally - wheel is awful for a small radius curves.
@@anatoliyzhestov3915 Sorry, but you are wrong. If the glass breaks wheel you use a wheel, you are no supporting the glass. Diamond only scratches. Ask any professional stained glass cutter.
@@tednelson5277 ask any professional you mention what he does and he will tell you - I draw hundreds of straight lines a day. In these conditions, a roller that can be changed frequently and is inexpensive is an advantage.
But among those who do small, precise work with small radii and want to get a very clean and precise cut, the number of diamond glass cutters may a lot surprise you.
This is so very very very beautiful, and as a glassworker I appreciate it so much!!!!!! Watching you try to cut glass without the correct breaking tools, and cutting twice though... 😛
I found your channel yesterday and I love your videos!!! Thank you so much for all the effort you put into your work. WE LOVE YOU URI!!!
I massively enjoy your videos
Cutting glass has been part of my profession for 24 years. It likes to fracture in straight lines, and in paths of least resistance. For that reason, scoring multiple times tends to cause jagged edges and additional fractures. A slow, deliberate and firm score works best. What can help with scoring is dabbing the cutter wheel on a sponge soaked in wd40. Idk why it helps, but it does. And when cutting circles/ovals score additional tangents to the circle so it looks like a whirlpool, making sure that there's about 5mm between the circle and the start of the tangent score. Tap the unsecured side of the glass, tracing the scoring. Tap the circular score first and gently so the scores become cracks. It will be visible when the scores crack. Once your circle is set, tap the tangent scores. The cracks should break to meet in the same direction on their own, and you can remove the loose pieces as they fall away.
Thanks for uploading. I always enjoy your content❤
_"Idk why it helps, but it does"_ - it lubricates the wheel, so it rolls easier on it's axis, and then WD-40/ kerosene/ glass cutting oil (yes, there is such oil) seeps into the score (which is a miniscule crack in the glass) - i.e. capillary force "push" it into the glass, and it either reduces the attraction between glass molecules (van der Waals force?) or in some other fashion facilitates the propagation of the initial crack (which is caused by "scoring", and lies underneath it) - or both (can't remember now exactly).
Also, "wiping off" the glass where you intend to make the score (just swipe yer finger across the glass) removes whatever dust have accumulated there and that helps to prolong the life of the wheel... or so I was told when I started my glazing job about twenty years before you did ;-)
@MrKotBonifacy this makes a lot of sense lol. Thank you
@@davidhoward496 Also, I forgot to say, but then you might know it very well yourself, so all the following is probably "teaching a priest how to say Lord's Prayer" but I'll write it anyway ;-)
So, high quality glass cutters have single wheel pivoting heads (so the head always stays 100% parallel to the direction of the cutting movement/ travel and/or the straight edge) and they have hollow brass handles which double as containers for cutting oil (which seeps down to the wheel lubricating it and wetting the score). Google for "silberschnitt oil glass cutter" (for example).
For regular "dry" cutters there are so-called oiling stands available, in which you place a small piece of cotton cloth or felt (a piece of a paper towel would also do) soaked in cutting oil - when you don't use the cutter you place it in this stand, and whenever you want to make a score the cutting head (and the wheel) is already oiled.
Also, I'm no longer doing any glazing (it's been "quite a while" since I quit it) - apart from occasional "could you help me, please?" for friends and such, and at any rate virtually all windows now use IGUs (aka double glazing units). Cheers!
I love the musical segments! Your videos are so much fun.
You are such a talented artist in many ways
This guy just kills me😂. You’re the best Mr. Tuchman. My favorite channel by a long shot.
Another work of art!
may i just say that the music choice is always on point!
Uri Tuchman, taking the ordinary and mundane and transforming it into art and light! You shine Uri.
trying new tools/workflow is always intimidating. I encourage you not to give up trying to incorporate those new processes. As much as I love seeing your brass/woodwork, It is refreshing to see you trying out new things and I hope you continue to do so.
Anyone with a hobby should be able to relate to the “spending millions of hours making some pieces of garbage!” So spot on. Thank you for this great video!
Never stop making those videos!
They are very entertaining! ❤❤❤
It’s so amazing, I can’t stop watching your art
What an incredibly beautiful looking tool you created Uri. I am so impressed & the hand done engraving just perfect!
Uri Tuchman, you make me smile every time I watch one of your videos. Thank you.
same. i love his personality
Great to see you engraving again also much admire your imaginative work.
Always a pleasure when I see a video from your's pop into my stream. Great job on the cool glass cutter. As always.
I remember while taking a class in school for stain glass, the trick was to make one, hard, continuous cut, not several cuts.
I recall needing quite a bit of pressure while using the cutter.
It is awesome how much this man has evoled, and grown. Even his social skills talking to viewers are noticeably better. I am a fan of this channel definitely!
I fell in love instantly with your channel, they are so engaging, thank you for the content !!
You make me happy, Mr Tuchman. I admire your willingness to try new things, fail, and learn. I think you are the most amusing and engaging engraver on the internet, so you might not be the master but you are very watchable and that is why you get my attention. Thank you.
Legendary as always!! Love the content!!
This "Golden Cut" brand reminds me of that Silberschnitt brand (German for "silver cut"), which was, if I'm not mistaken, a DDR "derivative" (knock-off) of West Germany Hartmetall glass cutters.
EDIT - just checked it, seems like "it's the other way round" - i.e. Silberschnitt was West Germany brand and Hartmetall was DDR "derivative".
And the quality of the wheel makes a "day and night difference" when it comes to glass cutting - so if you want to cut glass without any trouble get the best ones you can afford (within reasonable range, that is). This "home improvement/ hobbyist" brand is good just for that. Shops selling glazing tools and supplies sell cutting wheels "stand-alone" fashion, and there are plenty of sellers of these on all sort of internet selling platforms too. It's really worth getting high quality cutting wheels.
Then there are different cutting edge geometries for various thickness of glass (thick glass requires different angle grind of the cutting edge, more obtuse one AFAIR) and then there some special "glasses" (like X-ray shielding glass, which is made mostly of melted lead oxides, or that "glass-ceramic" thingy for fireplaces, like Robax) which require dedicated wheels as well.
Also, when cutting thick glass the force needed to score it is greater (thus different handles in such cutters) AND special pliers to run the crack, but when you use good quality new wheel the force applied should be "just enough" to score it - when you see tiny strands of glass flaking off by itself from the score (right after you made it) it means the force was too strong, and it will not only shorten the lifetime of the wheel (will blunt it, to put it bluntly... ;-) but this may actually worsen the quality of the cut.
And while light "tapping" the glass on the opposite side (underneath the score) with a hard object does "open up" the crack, the edges of it (where you tapped it) will be wavy - for regular glass thickness (2 - 6 mm) simple breaking it with your hands should do (if the score is right), preferably with "pulling apart" motion added.
Place the scored pane on a table so the score is still on the table but very close to the edge (5 mm or less) of it, hold it down with your left hand and "break off" that part outside of the table by pushing it with your other hand.
Or when the pane is too big for it, just lift it a little and place some soft (but firm) object under the score at the edge of the pane (a wooden handle of a regular glass cutter, or a pencil would do) and gently press the pane with your both hands placed 5 to 10 cm away from the score.
When the off-cut part is too narrow for any of the aforementioned methods use special pliers - regular workshop universal pliers are not suitable for this task. In a pinch they "will do", but very poorly - unless you have one of these special "parallel jaws" pliers. And at any rate the minimum off-cut width should be twice the thickness of the pane, or you may end up with a bit of a struggle and a rather jagged edge of the glass.
And, oh, BTW - hardened steel DOES score glass, but it's rather special kind of steel, with a lot of cementite in it, and VERY hardened ;-)
Looks like nowadays they make mostly carbide or PCD wheels though. Check the Bohle (Bohle AG) online store - bohle-dot-com.
Man, i remember watching you make your early tools for engraving...ty for sharing these years with all of us.
thank you for you content Uri !!!
_Of course_ you made the fanciest glass cutter! You're Uri Tuchman-it wouldn't matter what thing you made, it could not possibly be less than the fanciest example of that thing in existence!
Love the level up you performed with your video editing, bravo.
Video editing second to none. Great work all round. Thanks for the videos!
Watching you make things is very fun, especially the hand engraving! It’s so satisfying to watch and the results are always so nice.
As always Uri a pleasure watching one of your videos, so look forward to them as they are entertaining and you are a very talented guy, keep em coming
Your videos are a treat. Thank you for making them!
Your videos are as much works of art as the things you make in the videos. I get a goofy grin on my face watching them.
Beautiful work as ever, when you sang ‘All around me is a million pieces…’ that killed me. Awesome.
I really enjoy your videos, been watching for years!
Good to see you back Uri. Ive been worried about you. So happy you're making content again ❤️
the printing/casting headache was still cool to see attempted, sometimes things dont pan out, but we love the process of finding out what might!
I do stained glass window work in my free time. This thing is SO COOL. Love the utility of it.
Ok, fantástico trabajó maestro, un proyecto muyyyy original y peculiar, gracias por compartirlo con los pobres mortales, Uri un cordial saludo y por supuesto un merecido like desde Narón (Galicia)👍🤓😜
I used to be a “machine operator” for an aerospace contractor. Which is sort of like being a machinist without the in-depth knowledge… Man all I can say is you a fantastic craftsman! You make it look easy but that takes some real skill! Keep up the great work.
Great video. I really love your style, energy and your honesty. I miss you describing your creations as delicious 😂
Uri so clever Uri. I love your sense of huma
i love your work and your bizarre nature, thank you for doing what you do!
14:50 i love you too
Oh man!!!! Your projects are approching clickspring's quality! This cutter looks amazing
While everyone is trying to explain how to cut glass, I just want to say that little Derringer is BadASS! Beautiful engraving, nice handle, clever hinge and the case is perfect! Good job. If you come to the Maker Faire in California, I'll see you there. Bicycle rodeo!
Wow Uri! The video editing is amazing in the last videos.
(Also... Always preheat the mold before the pour)
The way glass cutters work is "stress concentration" which just means that they make a very sharp but shallow gash in the surface which should make the glass split right there. The reason this works is because what breaks a material isn't just the amount of force but the force divided by the area where the force is applied which is called stress. So, if you make that area very small, like at the tip of a very sharp scratch, the stress becomes huge. So, it's actually better to make a single fine scratch with the glass cutter rather than going over the same line may times because while you're making the gouge deeper, you're also making it wider and thus duller
Your skills are amazing . Your falability is endearing. I could watch you for hours.
Beautiful job
Great work again, Uri
Great stuff Uri!
Its crazy to see a skilled artisan give up the moment he hits the slightest resistance with something new. I never expected it.
Brilliant as ever!! 🎉🎉
This video is your masterwork. Bravo
Absolutely beautiful.
Great photography and soundtrack! Groovy Glass Gun should be your next composition.
I can testify that your glass cutter works as well as any commercial one ever has for me.
Uri, I think next big project will be investment casting. It will allow to have smallest details. You can nickel plate locally with a wet sponge. If your steel quenched in water then it is W1. O1 is quenching in oil. I had also negative experience with glass cutting. When you scratch the glas you create a weak zone. Doing it multiple times does not help and opposite. When you start applying stress it does not cocentrate if you have several scratches. Perfect video. As always!
I’m glad you made the correction because I was pretty sure the cutters were made of carbide or sometimes diamond.
I've tried casting tin with that same high temp silicone, casting a 3D printed coin. I think the problem we both ran into is that the tin cools too quickly. The mold needs to be a material that can be heated (sand, ceramic, etc) so the tin cools slowly and can get into all the nooks and crannies. In my case all the holes and imperfections made the coins look like old, corroded shipwreck treasure so it worked out okay.
Watching screws or bolts get made on a lathe feels insane every time I see it.
Watching that big log of metal getting cut down so much until there's a tiny screw
Haha don't change one bit Uri! Loving the music at the 12:00 mark, very funny. Also have you thought of using a toggle clamp to hold down your work piece when drilling on the drill press? They are very cheap and work super well!
You rock Uri!
Another video already!!!! Excellent. Getting a cup of tea and a couple biscuits and I'll be right back.
3:55 Song name is Funk Wife Punk Life L.M. Styles
do you know what the 10:41 song name ?
I really wanna know the 10:41 song as well! It’s awesome.
@@____________________K i think it's "Lupus Nocte - Getting Lost" not sure tho, just looked it up with: i'm getting lost from what i heared from the lyrics
@@aschilinggs841 damm you right !! Thanks ma dude 👍👍
Your work is amazing!!
Awesome edit at 11:30+
I really enjoyed this one! Great content. More singing please😂
Hi Uri, after spotting you at last years show and missing the opportunity to say hello I will pop over this time and have a natter !!! Great work mate, fun as always !!
I have a tip for getting the curved cuts, and cool enough, it's a secret feature you added to the cutter and didn't know it! Turn that sucker around and hit the glass with the butt of the gun multiple times along the scores. Not so hard to shatter it, but firm enough to make it vibrate. It causes micro fractures along the score lines, and eventually the microfractures will all connect and the glass will just pop apart where you scored it. On a standard glass cutter, that's why it will often have a large ball on the handle end, but the butt of the gun would likely work really well for that!
Also, your work is really awesome and I love seeing your ideas to fix problems; like the offset screw that covers the pin.
I so look forward to your videos!
Came for the the beautiful build, stayed for the iconic personality
Of all the Creators on TH-cam Uri is the one the entire world wants to have coffee with...You are the most interesting man in the world!
Beautiful work.
Once ! That's all despite the thickness !
Brilliant build , great craftsmanship ( or patience) 😁 .as usual
👍👍👍👍👍👍👍👍👍
"Do a little Circumcish" you're the best bud. Freakin love your channel
As a stained glass art maker, my advice is this: Glass cutting oil will improve performance and reduce chipping...or at least reduce the distance the chips fly, therefore being safer for your eyes. Also, please wear safety glasses when glass cutting! The oil reduces the wear on the cutting wheel because of the reduced friction.
Thank You Uri Tuchman... GREAT ONE !!!!!!!! BEAUTIFUL AND FUN TO WATCH!!!!!
(Q- HOW DO I GET THAT LAST LITTLE BIT OF TOOTHPAST OUT OF THE USED UP TOOTHPAST TUBE????????? ) ... TM
Thanks for sharing.
I second the comments saying that the casting molds need some "spouts". Places where the extra metal can go, chasing air out. But for such fine detail you probably need to use an injection mold. I tried making flat molds but the result needs a lot of additional work to remove excess metal on the back and possible re-work details.
Having said that, the result is amazing, it looks so cool! I hope the client sends you photos of it in use
This person has a special charisma. He is like me in trying to use technology in my work, but I quickly return to my classic method.
Oh what an Idea.You areno doubt a master craftsman
You are a very good singer 😂. Keep on going!
Brilliant editing!! Well done, you made me laugh a few times, thank you for this, stay safe and healthy 💚